Question about Chevrolet Cruze

1 Answer

Need torque sequence for main saddle bolts . 22 in total for a 2012 chevy Cruze ecotek 1.4l turbo

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 5,274 Answers

Special Tools

  • EN-235-6 Installer
  • EN-470-B Angular Torque Wrench
  • EN-658-1 Installer
For equivalent regional tools, refer to Special Tools.


  1. Install a NEW crankshaft position sensor reluctor ring?(1) and the 3?bolts?(2).
  2. Tighten the 3?bolts?(2) to 10?Y?(89?lb?in).
  3. Lubricate crankshaft, crankshaft bearings and crankshaft bearing cap tie plate with engine oil.

  4. Install the 4?upper crankshaft bearings?(2) and the crankshaft thrust bearing?(3).
  5. Install the crankshaft?(1).

  6. Note: The thickness of the sealing bead should be 2?mm?(0.0787?in).
  7. Apply sealing compound?(1) to the outer rim of the groove on the crankshaft bearing cap tie plate. Refer to Adhesives, Fluids, Lubricants, and Sealers.


  8. Note: The complete installation procedure should not take longer than 10?minutes.
  9. Install the 4?lower crankshaft bearings?(3) and the lower crankshaft thrust bearing?(4).
  10. Install the crankshaft bearing cap tie plate?(2).
  11. Note: Do not reuse the old bolts.
  12. Install the 10?NEW inner crankshaft bearing cap tie plate bolts?(1).

  13. Caution: Refer to Fastener Caution. Caution: Refer to Torque-to-Yield Fastener Caution.
  14. Tighten the 10?inner crankshaft bearing cap tie plate bolts in the sequence shown and to the following specifications:
    1. Tighten the inner crankshaft bearing cap tie plate bolts to 25?Y?(18?lb?ft).
    2. Tighten the inner crankshaft bearing cap tie plate bolts an additional 60?degrees, using the EN-470-B wrench.
    3. Tighten the inner crankshaft bearing cap tie plate bolts an additional 15?degrees, using the EN-470-B wrench.


    Note: Do not reuse the old bolts.
  15. Install the 12?NEW outer crankshaft bearing cap tie plate bolts?(1) and tighten to the following specification:
    1. Tighten the outer crankshaft bearing cap tie plate bolts to 10?Y?(89?lb?in).
    2. Tighten the outer crankshaft bearing cap tie plate bolts an additional 60?degrees, using the EN-470-B wrench.
    3. Tighten the outer crankshaft bearing cap tie plate bolts an additional 15?degrees, using the EN-470-B wrench.


  16. Install the crankshaft position sensor?(1) and a NEW crankshaft position sensor seal ring?(2).
  17. Install the crankshaft position sensor bolt?(3) and tighten to 8?Y?(71?lb?in).


  18. Note: Lubricate the crankshaft rear oil seal.
  19. Install the crankshaft rear oil seal?(1) with EN-235-6 installer?(2).


  20. Use EN-658-1 installer?(1) to strike the crankshaft rear oil seal.



  21. My database showed this info. Only the inner 10 showed a sequence. The outer 12 didn't.










Posted on Feb 02, 2018

  • jack layton
    jack layton Feb 02, 2018

    My info didn't state engine size or turbo.

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
wilsodfarm
  • 986 Answers

SOURCE: Head bolt torque spec and sequence

Torque to yeild bolts need to be replaced whenever the head comes off.....Long bolts are 46 ft lbs. and the turn 90 degrees (1/4 turn) short bolts are 43 ft. lbs. and then 90

Posted on Oct 21, 2009

alicantecoli
  • 22484 Answers

SOURCE: torque settings for fiesta rs turbo cylinder head

wow a real car ,1.6 crossflow engine ??about 75lbs and start in middle of head then one to the right and one to the left till you come to end oif the head ,Turbo ?? could be a bit more especially as this engine has a cast iron head ,cant be lot more though because the ford dorset engine turbo diesel is only 120 ,normal "D" series dorset engine is 90 .go to 75 and it feels ok leave well alone ,could push 80 but ?? remember the cortina 1600E with the bunch of bananas exhaust manifold

Posted on Apr 03, 2010

tburtk
  • 158 Answers

SOURCE: i need torque specs for a 2004 dodge cummins 24

http://www.dieseltruckresource.com/dev/index.php

I suggest this website for your dodge truck needs.

Posted on May 13, 2010

  • 3640 Answers

SOURCE: i need the engine torque specs for 99 chevy malibu

99 chevy malibu v6 3.1 engine, head bolt torque is-- 98 through 2001 is step1- 37 foot lbs, step 2- rotate an additional 90 degrees (1/4 turn). the rocker arm bolts are 168-in. lbs.

Posted on Sep 07, 2010

HansPP
  • 2510 Answers

SOURCE: what is the torque on

The head torquing sequence for any cylinder head is as below, continue the pattern if there are more than 10 bolts:-


10 6 1 3 7

8 4 2 5 9

Start at the middle two bolts and do your sequence at least three times, first at about half the torque, then the full torque value at least twice. It is good practice to re torque the head again after about 1000 km (600 miles), but this is often disregarded due to the problems of getting to the head bolts.

Posted on Jan 29, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

Nissan altima 2.4 L torque specs.


Torque sequence ---------------- | 9 3 1 6 8 | | 7 5 2 4 10 | ---------------- Step 1: Torque in sequence 22 Ft/Lbs Step 2: Torque in sequence 58 Ft/Lbs Step 3: Loosen all bolts completely Step 4: Retorque all bolts in sequence 22 Ft/Lbs Step 5: Retorque all bolts in sequence 54-61 Ft/Lbs recheck final torque in sequence *** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque. 0900c15280265395.jpg

on Jul 08, 2010 | Nissan Altima Cars & Trucks

1 Answer

What are the torque specs and sequence for the intake and head gasket on a 1999 Chevy Silverado 6.0l V8 K2500


Cylinder Head Bolts (First Pass all M11 Bolts in Sequence)
30 N?·m
22 lb ft
Cylinder Head Bolts (Second Pass all M11 Bolts in Sequence)
90 degrees
Cylinder Head Bolts (Final Pass all M11 Bolts in Sequence-Excluding the Medium Length Bolts at the Front and Rear of Each Cylinder Head)
90 degrees
Cylinder Head Bolts (Final Pass M11 Medium Length Bolts at the Front and Rear of Each Cylinder Head in Sequence)
50 degrees
Cylinder Head Bolts (M8 Inner Bolts in Sequence)
30 N?·m
22 lb ft
Intake Manifold Bolts (First Pass in Sequence)
5 N?·m
44 lb in
Intake Manifold Bolts (Final Pass in Sequence)
10 N?·m
89 lb in
Intake Manifold Wiring Harness Stud
10 N?·m
89 lb in

Oct 27, 2015 | Cars & Trucks

1 Answer

F77 2.8 diesel non turbo.1989 model.require head bolt tensions,stages and sequence please


Search Results

    F77 2.8 diesel non turbo.1989 model.require head bolt - Fixya

    www.fixya.com/cars/t25792470-f77_2_8_diesel_non_turbo_1989
    Jul 22, 2015 - f77 2.8 diesel non turbo.1989 model.require head bolt tensions,stages and sequence please - Daihatsu Rocky question. ... Torque to yeild bolts need to be replaced whenever the head comes off.....Long bolts are 46 ft lbs. and ...

Jul 22, 2015 | Daihatsu Rocky Cars & Trucks

1 Answer

Torque specs &and sequence for a 2011 chevy cruze 1.4 turbo head


26 lb ft and aditional 180 degees the secuence is from the center go on circles to the out side

Jul 17, 2015 | 2011 Chevrolet Chevrolet Cruze ECO

1 Answer

Need head bolt torque specs for a 1996 saturn sl


Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 | 1996 Saturn SL

1 Answer

Workshop manual for a 1994 nissan serena


Cylinder head bolt torque sequence
The Rod Bearing Cap Torque
The Main Bearing Cap Torque 38 Foot pounds (Final torque)


Step 1: Torque 10-12 Ft/LbsStep 2: Torque 17-21 Ft/Lbs


Note :
Torque sequence ------------------------
' 11 '
front ' 13 9 3 1 6 8 '
of ' '
engine ' 14 7 5 2 4 10 '
' 12 15 '
------------------------
Step 1: Torque all bolts in sequence 22 Ft/Lbs
Step 2: Torque all bolts in sequence 47 Ft/Lbs
Step 3: Loosen all bolts in reverse sequence
Step 4: Retorque all bolts in sequence 22 Ft/Lbs
Step 5: Retorque all bolts in sequence 43-51 Ft/Lbs
Step 6: Retorque bolts 11 thru 15 in sequence an
additional 4-6 Ft/Lbs
** CAUTION ** This engine uses 2 different length head
bolts. "#1" Is the long bolt, while remaining bolts
are short. **Do not confuse location of these bolts**
recheck final torque in sequence

Dec 06, 2012 | Cars & Trucks

1 Answer

Need torque specs foe a 2000 jeep with a 4.0 to be spacific i need the mains rods and head


Hello mooredavid42,

The Head bolt torque is as follows:

1. Tighten all bolt in the sequence shown in the image below to 22 ft. lbs.
2. Tighten all bolt in the sequence shown in the image below to 45 ft. lbs.
3. Check all bolt to verify they are torqued to 45 ft.lbs in the sequence shown below.
4. Tighten bolts in sequence:
a. Bolts 1-10 to 110 ft.lbs.
b. Bolt 11 to 100 ft. lbs.
c. Bolts 12-14 to 110 ft.lbs.

If you are reusing the head bolts carefully check the bolts for necked down threads.

netvan_199.png

The main bearing cap bolts are torqued to 80 ft. lbs.

The connecting rod nuts are torqued to 33 ft. lbs.

I hope this helps.

Regards,

Jerry

Aug 24, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

Looking for the torque specs for 1998 chevy astro van?


1998 chevy astro 4.3 v6 torque specs include :
* foot pounds *
balance shaft (if equiped) gear bolt = step 1 = 15 ft.lbs. step2 = additional 35 degrees.
camshaft sprocket bolt = 18 ft. lbs.
connecting rod cap = step 1 = 20 ft. lbs. step 2 = additional 70 degrees.
crankshaft damper bolt = 74 ft. lbs.
crankshaft oil deflectorbolt/nut = 27 ft.lbs.
cylinder head bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees. (tighten in sequence)
2811243.jpg


exhaust manifold bolts = step 1 = 11 ft. lbs. step 2 = 22 ft. lbs.
flywheel bolt = 74 ft. lbs.
main bearing cap bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees.
oil filter adapter bolt = 15 ft. lbs.
oil pan bolt/nut = 18 ft. lbs.
oil pump bolt = 66 ft. lbs.
rocker arm with press in studs = 18 ft. lbs.
rocker arm with screw in studs = 19 ft. lbs.
valve lifter retainer bolt = 12 ft. lbs.
water pump bolt = 33 ft. lbs.
* inch pounds *
balance shaft retaining plate bolt = 106 in. lbs.
camshaft retainer plate bolt = 106 in. lbs.
front cover bolt = 106 in. lbs.
intake manifold upper = step 1 = 44 in. lbs. step 2 = 88 in. lbs.
intake manifold lower = step 1 = 27 in. lbs. step 2 = 106 in. lbs. step 3 = 133 in. lbs. ** (tighten bolts in sequence)

cbb8861.jpg

thanks for your vote !

Dec 28, 2008 | 1998 Chevrolet Astro

4 Answers

Chevy 5.7 17 bolt heads tork specs


Cylinder Head Bolt (Preferred Method) All Bolts First Pass in Sequence 22 ft.lb Long Bolt Final Pass in Sequence 75 deg. Medium Bolt Final Pass in Sequence 65 deg Short Bolt Final Pass in Sequence 55 deg. Cylinder Head Bolt (Optional On-Vehicle Strategy) First Pass in Sequence 26 ft.lb Second Pass in Sequence 44 ft.lb Final Pass in Sequence 66 ft.lb

Oct 13, 2008 | 1999 Chevrolet C1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...