Which fuse should I check first?
The ultrasonic rear parking assist (URPA)
The URPA is equipped with a switch located above the driver information center (DIC) that can be used to disable the system.Do you have it disabled ?
Diagnostic Trouble Code (DTC) Displaying
This vehicle is equipped with an on-board diagnostic display feature capable of displaying diagnostic trouble codes using the 3 indicators on the rear parking assist display. After the bulb check has been completed, the red outside indicator flashes to indicate a malfunction with the system. The module disables operation of the URPA system under this condition.
In order to enter the diagnostic mode, complete the following actions:
With the ignition turned OFF, short the rear parking assist diagnostic connector to ground while the vehicle is in PARK. For the location of the rear parking assist (RPA) diagnostic connector, refer to Object Detection Component Views . It's under the front of the center console , by the BCM - body control module.
Turn ON the ignition.
Place foot on the brake.
Shift the vehicle into REVERSE within 5 seconds.
If the vehicle is not shifted into reverse within 5 seconds after turning the ignition ON, the diagnostic mode will still be initiated. However, a reverse input wiring fault will be registered as sequence #7 as shown in the Diagnostic Indicator table below. Refer to Diagnostic Trouble Code (DTC) Clearing for the specific steps on how to clear diagnostic trouble codes. After the reverse input wiring code is cleared, repeat the diagnostic trouble code displaying steps in order to enter the diagnostic mode.
When the diagnostic mode is first entered, the rear parking assist display displays the amber outside indicator and the red outside indicator. Then, the indicators on the rear parking assist display will display one or more of the sequences in the table below to indicate where the fault exists within the rear parking assist system. Refer to Diagnostic Trouble Code (DTC) Clearing for the specific steps on how to clear diagnostic trouble codes.
Diagnostic Indicators #
State/Fault Location
Amber Outside
Amber Middle
Red Outside
Flashing
1
Start of Diagnostics
X
--
X
--
2
RR Corner Object Sensor and Wiring
X
--
--
--
3
RR Middle Object Sensor and Wiring
X
X
--
--
4
LR Middle Object Sensor and Wiring
--
X
X
--
5
LR Corner Object Sensor and Wiring
--
--
X
--
6
Chime Warning Wiring
--
X
--
--
7
Reverse Input Wiring
--
X
--
X
8
Important: This diagnostic pattern sets for an open sensor supply voltage circuit and sensor low reference circuit.
Sensor Supply Voltage Circuit and Sensor Low Reference Circuit
X
X
X
X
Flashes in the following sequence:
Amber Outside
Amber Outside and Amber Middle
Amber Middle and Red Outside
Red Outside
9
Important: This diagnostic pattern sets for a short to ground in the sensor supply voltage circuit.
Sensor Supply Voltage Circuit
X
X
X
--
SOURCE: 2003 buick rendezvous power outlets
Fuse #14 is for REAR auxillary power outlet (in cargo area). This is located in the INSIDE fuse box to the left of and under the glovebox (to the left of the front passenger's feet).
Fuse #32 is for FRONT Power Outlets/cigarette lighter//Lights, OnStar® Fuse 32 is under the hood in the ENGINE AREA fuse box located in the compartment just above the battery.DOUBLE CHECK YOUR MANUAL to make sure that your fuses are the same. I have a 2003 Rendezvous. Your newer model may be different. The diagrams for each fuse box can be found inside the lids of the compartments.
SOURCE: Gas gauge problems with 2004 Buick Rendezvous
No, there is not a fuse for this. Unfortunately, you have a bad sending unit. In order to replace the sending unit you have to drop the gas tank. Sooo............drive it more to get rid of all of that gas and it will be easier to put back up.
please remember to rate this solution.
SOURCE: I have a 2002 Buick Rendezvous and neither of my
Try checking fuse #32 located in the fuse box under the hood for the bad fuse.
I hope this helps! :)
Testimonial: "Thanks! But now it blows whenever I plug in the phone charger..."
SOURCE: i have 2004 buick rendezvous and the blower motor
{: ) If all other HVAC functions seem to be working normally except for the blower air, the most likely cause is a faulty blower resistor assembly ( for manual a/c) or a faulty blower motor control processor( for automatic control a/c). The blower motor can be easily checked if stucked-up or open-circuited. Inspect and repair (or replace) connectors and terminals for these components if you found them heated up or burned.
Testimonial: "thank you you info was very helpful"
SOURCE: blower motor not working all fuses good.2003 buick
I just replaced the blower motor resistor on my 2003 Rendezvous. I bought the resistor at the GM dealership for $48 (AC Delco). The part number was 25928168. The fan now works in all five speeds.
For electrical parts, I only trust the dealership for the latest revised components.
1,783 views
Usually answered in minutes!
×