Side Marker Bulbs

Removal Procedure

1. Open the hood.
2. Remove the headlamp. Refer to Headlamp Bulb Replacement .
3. Rotate the bulb and socket counterclockwise in order to remove the bulb and socket from the housing. Remove the side marker bulb (3) or turn signal/park bulb (4) from the socket.
   

You don't need a dealer for much of anything

All of todays vehicles require removing the lamp
assembly or housings,front or rear, of any vehicle,to
take out the lamps/bulbs

If you open the hood you will find screws that hold it in place

May not be an easy job, but that's the junk were sold

Side Lamp/Front Turn Signal Lamp Bulb

Removal and Installation

1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02.

1. Remove the 2 fender splash shield bolts.

1. Remove the 3 fender splash shield pin-type retainers.

1. Remove the screw and position the fender splash shield aside.

1. Remove the front turn lamp bulb holder from the lamp assembly.

1. Remove the front turn lamp bulb.

1. To install, reverse the removal procedure.

Removal & Installation
Bulb Replacement
To Remove:

CAUTION
Halogen bulbs contain pressurized gas.
Mishandling a bulb may result in the bulb shattering into flying glass
fragments.

CAUTION
Make sure to wear eye protection when
handling a halogen bulb.

CAUTION
Do not touch the glass of a halogen bulb,
only handle the bulb by the base.

CAUTION
Do not allow a halogen bulb to come into
contact with dirt or moisture.

CAUTION
Make sure to dispose of a used halogen bulb
properly.

CAUTION
Do not allow children to handle halogen
bulbs.

1. Turn the lamp switch to the off position.
   
2. Make sure the bulb is cool before changing.
   
3. Remove the headlamp assembly from the headlamp panel.
   
4. Remove the rear access cover from the headlamp assembly.
   
5. Disconnect the headlamp connector.
   
6. Remove the bulb from the headlamp assembly by rotating the bulb and socket
   counterclockwise.

To Install:

1. Connect the headlamp connector.
   
2. Install the bulb into the headlamp assembly by rotating the bulb and socket
   clockwise.
   
3. Install the rear access cover onto the headlamp assembly.
   
4. Install the headlamp assembly into the headlamp panel.

Headlamp Assembly
Chevrolet
To Remove:






Headlamp Assembly (Chevrolet)

1. Remove the grille from the front of the vehicle.
   
2. Release the headlamp assembly retaining tabs.
   
3. If equipped, disconnect the headlamp leveling motor connector.
   
4. Disconnect the headlamp connector.
   
5. Remove the park/turn and side marker bulb sockets from the headlamp
   assembly.
   
6. Remove the headlamp assembly from the headlamp panel.

To Install:

1. Place the headlamp assembly into the headlamp panel.
   
2. Install the park/turn and side marker bulb sockets into the headlamp
   assembly.
   
3. Connect the headlamp connector.
   
4. If equipped, connect the headlamp leveling motor connector.
   
5. Lock the headlamp assembly retaining tabs.
   
6. Install the grille onto the front of the vehicle.

GMC, Oldsmobile, Buick, Isuzu, and Saab
To Remove:






Headlamp Assembly (GMC, Saab, Oldsmobile, and Buick)

1. Release the headlamp assembly retaining tabs.
   
2. Disconnect the headlamp connector.
   
3. Remove the park/turn bulb socket from the headlamp assembly.
   
4. For GMC, Saab, Oldsmobile, and Isuzu vehicles, remove the side marker bulb
   socket from the headlamp assembly.
   
5. Remove the headlamp assembly from the headlamp panel.

To Install:

1. Place the headlamp assembly into the headlamp panel.
   
2. For GMC, Saab, Oldsmobile, and Isuzu vehicles, install the side marker bulb
   socket into the headlamp assembly.
   
3. Install the park/turn bulb socket into the headlamp assembly.
   
4. Connect the headlamp connector.
   
5. Lock the headlamp assembly retaining tabs.

REMOVAL PROCEDURE

1. Open the hood.
2. Remove the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly to flex forward.
3. Remove the bolt and the push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.

1. Gently pull the upper fascia and grille assembly forward only far enough to remove the bolt located at the bottom inboard side of the headlamp assembly.
2. Pull the headlamp assembly straight out to disengage the snap-in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the front inboard corner clears the front fascia.
3. Pull the headlamp assembly out and away from the vehicle
4. Disconnect the headlamp electrical connector.
5. Remove the headlamp assembly from the vehicle.
6. Remove the headlamp bulb cover from the headlamp assembly.
7. Remove the headlamp bulb socket from the headlamp assembly.

CAUTION: Refer to Halogen Bulb Caution in Service Precautions.

1. Remove the headlamp bulb.
2. Remove the side marker bulb socket from the outer side of the headlamp assembly.
3. Remove the side marker bulb.
4. Remove the parking lamp bulb socket from the inner edge of the headlamp assembly.
5. Remove the parking lamp bulb.

INSTALLATION PROCEDURE

CAUTION: Refer to Halogen Bulb Caution in Service Precautions.

1. Install the headlamp bulb to the socket.
2. Install the headlamp bulb socket to the headlamp assembly.
3. Install the headlamp bulb cover to the headlamp assembly.
4. Install the side marker bulb to the socket.
5. Install the side marker bulb socket to the headlamp assembly.
6. Install the parking lamp bulb to the socket.
7. Install the parking lamp socket to the headlamp assembly.
8. Connect the headlamp electrical connector.
9. Install the headlamp assembly to the vehicle by placing it back into position so that the bolt holes align and the snap-in retainer located at the outboard back surface of the headlamp assembly engages.
10. Gently pull the upper fascia and grille assembly forward only far enough to install the bolt located at the bottom inboard side of the headlamp assembly.

NOTE: Refer to Fastener Notice in Service Precautions.

1. Install the bolt and push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.

Tighten the bolts to 6 N.m (53 lb in).

1. Install the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly.
2. Close the hood.

Headlamp Removal & Installation Bulb Replacement To Remove:

1. Remove the Headlamp Assembly. Headlamp bulbs
   
   
2. Turn the high/low beam bulb socket counterclockwise to remove.

To Install:

1. Turn the high/low beam bulb socket clockwise to install.
2. Install the Headlamp Assembly.

Headlamp Assembly (Park, Turn, Cornering and Side Marker Lamps) To Remove:
Headlamp assembly R &I

1. Rotate the headlamp assembly retainer pins and pull up to remove.
2. Remove the mounting bolts.
3. Disconnect the harness connectors.

To Install:

1. Connect the harness connectors.
2. Position the headlamp assembly on the panel.
3. Rotate the retainer pins and push down to lock in place.
4. Install and secure the mounting bolts.

Headlamp Removal & Installation Bulb Replacement To Remove:
CAUTION
Halogen bulbs contain pressurized gas. Mishandling a bulb may result in the bulb shattering into flying glass fragments.
CAUTION
Make sure to wear eye protection when handling a halogen bulb.
CAUTION
Do not touch the glass of a halogen bulb, only handle the bulb by the base.
CAUTION
Do not allow a halogen bulb to come into contact with dirt or moisture.
CAUTION
Make sure to dispose of a used halogen bulb properly.
CAUTION
Do not allow children to handle halogen bulbs.

1. Turn the lamp switch to the off position.
2. Make sure the bulb is cool before changing.
3. Remove the headlamp assembly from the headlamp panel.
4. Remove the rear access cover from the headlamp assembly.
5. Disconnect the headlamp connector.
6. Remove the bulb from the headlamp assembly by rotating the bulb and socket counterclockwise.

To Install:

1. Connect the headlamp connector.
2. Install the bulb into the headlamp assembly by rotating the bulb and socket clockwise.
3. Install the rear access cover onto the headlamp assembly.
4. Install the headlamp assembly into the headlamp panel.

Headlamp Assembly Chevrolet To Remove:
Headlamp Assembly (Chevrolet)

1. Remove the grille from the front of the vehicle.
2. Release the headlamp assembly retaining tabs.
3. If equipped, disconnect the headlamp leveling motor connector.
4. Disconnect the headlamp connector.
5. Remove the park/turn and side marker bulb sockets from the headlamp assembly.
6. Remove the headlamp assembly from the headlamp panel.

To Install:

1. Place the headlamp assembly into the headlamp panel.
2. Install the park/turn and side marker bulb sockets into the headlamp assembly.
3. Connect the headlamp connector.
4. If equipped, connect the headlamp leveling motor connector.
5. Lock the headlamp assembly retaining tabs.
6. Install the grille onto the front of the vehicle.

1. Open the hood.
2. Remove the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly to flex forward.
3. Remove the bolt and the push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.
1. Gently pull the upper fascia and grille assembly forward only far enough to remove the bolt located at the bottom inboard side of the headlamp assembly.
2. Pull the headlamp assembly straight out to disengage the snap-in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the front inboard corner clears the front fascia.
3. Pull the headlamp assembly out and away from the vehicle
4. Disconnect the headlamp electrical connector.
5. Remove the headlamp assembly from the vehicle.
6. Remove the headlamp bulb cover from the headlamp assembly.
7. Remove the headlamp bulb socket from the headlamp assembly.
8. Remove the headlamp bulb.
9. Remove the side marker bulb socket from the outer side of the headlamp assembly.
10. Remove the side marker bulb.

i think there are two flat guide pins that hold the headlight assembly in .. just pull them straight up ..and the assembly should come out ..hencse replace the bulbs.

I hve the same issue. I have replaced all the bulbs on the fron and back of the left side of the car and still the left front blinker does not blink.