How do you bleed the brakes of a 2016 Lexus 350?

Question edited for clarity and spelling of maker 'Lexis' to Lexus.
Question moved to model category.

Get underneath the engine and attach a battery charger positive to the positive lead on the starter and a clean bolt on the engine or bodywork. In 15 minutes, you will be able to open the door.

Alternatively there is the easy way, use the emergency door key that is hidden in the fob.

Manually Unlock Lexus - Dead Battery

youcanic https://www.youcanic.com > Vehicles > Lexus
Nov 6, 2023 - To unlock a Lexus with a dead battery, you can use the emergency metal key inside the keyfob to unlock the driver's doors. The instructions in ...

How to open the car or hood when battery is dead

ClubLexus https://www.clublexus.com > rx-4th-gen-2016-2022
Jun 6, 2019 - Driver door has a lock cylinder. Pull the physical key out from the fob and pull the driver door handle and look in the gap between the door ...

RX-350 Dead Battery, Mechanical key wont open - ClubLexus
Apr 19, 2022
HELP! dead battery and the car is locked - ClubLexus
Feb 20, 2009
Door locks operaton with a dead battery - ClubLexus
Jul 27, 2020
How to open the car or hood when battery is dead - Page 4
Jun 6, 2019
More results from www.clublexus.com ..

here is a picture of your brake caliper. on the upper richt hand corner you should see a spout on a hex bolt, this is your brake bleeding nozzle. http://www.partsgeek.com/catalog/2006/lexus/gx470/brake/brake_caliper.html

to bleed brakes you fill the brake fluid, leave the cap off, mash in the brake pedal and hold, while someone else opens and closes the brake bleeding nozzle on the caliper. do not release the brake pedal until the nozzle is shut, then check to see if the brake fluid needs filled again. do this at least 3 times, (mash, losten, tighten, release, check level) for each wheel, starting on the furthest away wheel from the point where the air entered the system, moving towards the one closest to the repaired leak.

it is a 2 man job unless you get a kit, or tubes and buckets.

Daren,here's a link to bleeding your brakes. http://www.autozone.com/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f80382b70 Here's a link on ABS bleeding if you can't get the height with the regular bleeding. http://www.autozone.com/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f80382a10

posible bad or frozzen left caliper

Remove wheels and check brakes espec,. Hand brake.

Push the brake and check the power at the starter, if you have power at the starter, then the problem is with the starter, if not then the problem is with the switch at the brake.

change master cylinder its bad internally

Have the rear brakes inspected for worn out brake pads is the first thing to do. most tire shops will do a brake safety inspection for free.

Press brake, let off. Open bleed screw until the fluid runs out with no bubbles. Tighten bleed screw. Press brake and hold. Open bleed screw until pedal goes to floor then close bleed screw with pedal pressed to floor.. Fluid should come out with no air bubbles when open. If they are present repeat the last part.

The bleeder screw is in the back next to the brake line into the caliper. Start the bleeding at the right rear, farthest from the reservoir. Then move towards the front left. Keep checking the fluid level and make sure you don't let go of the pedal with the screw loose. Get a 6 point box wrench on there , about 8mm, and a piece of hose to run the fluid into an empty can. Check it out, hope this helps.