Replace fender on toyora echo

SOURCE: 2000 toyota echo, wheel bearings

I found this site to be very helpful with this job: http://www.toyotanation.com/forum/showthread.php?s=714b28cb1c3f77f992209de0bdbfbd13&p=2481776#post2481776

SOURCE: replace broken driver side turn signal lights - left fender

reach screwdriver down between headlight and marker to releace clip, pull forward.

SOURCE: Front fender removal

Hiya... here's the details of fender removal/installation:
the left-side (same for right-side) fender has 6 bolts attached to the "sidebody" frame.
The bolt location:
3 are on the top fender-easy to find when hood is open,
1 is hidden at the rear of top inner fender-just open the left-front door wide to find it (early equinoxes had foam-like noise absorber material in it, just remove it from underneath fender after the wheelwell liner is removed),
1 bolt is hidden at bottom of front fender area at headlight/bumper area-you need to remove plastic wheelwell liner to gain access,
1 bolt is hidden at bottom of rear fender area where the black plastic rocker panel meets below the fender...
THIS area is probably the most difficult task to do since it requires you to remove a small bolt found on the front of rocker panel behind the front-left wheel then use a flat screwdriver or clip removal tool to pry open the black plastic **clip's 'dime-sized' head prior to pull out the clip's body (it has 8 clips underneath the chassis) then use your hands to grasp the rocker panel underneath, pull it down-toward you...this should do it....USE CARE during rocker panel and clip removal/installation so you don't break the clips!
It also has yellow plastic clips inside the rocker panel (used as a guide during installation into rocker sill holes-use caution not to break it)
**note: early equinoxes had rocker panel clips that you can actually pull it out from the hole, while later equinoxes has 'built-in' clips inside rocker panels that you don't see the clip heads below it due to engineering part design change**
Be sure to exercise care when handing this task!

SOURCE: replace front fenders 1999 wrangler

Hi! In your case you have to read this STEP by STEP instruction how to replace fenders

1. First, raise the front of the car and rest it securely on jack stands.
2. Remove the front wheels (the fender can be removed with the wheels on, but you'll have limited access to the fender bolts -- we recommend removing the wheels).
3. If you're removing the left front fender on a 1968 through 1973 model, unplug the horn wires and remove the horn. Don't hang the horn by the wires.
4. Remove the bumper and bumper brackets
5. First remove the headlights and turn signal lights and wrap the wiring up out of the way.
6. Remove the nut, washer and bolt that attach the fender to the running board.
7. Remove the bolts and nuts that attach the fender to the body.
8. Remove the fender, the beading, and the rubber spacer between the fender and the running board. Note: The rubber bead has cutouts around the bolt holes (it doesn't have holes in it - just cut outs).
   
9. Inspect the rubber beading and the rubber spacer washer. If they are cracked, dried, or deteriorated, replace them.
   
   
10. Check the threaded holes in the captive nuts in the body and clean them up with a tap if necessary. Lubricate the bolt threads.

1. Place the fender in position against the body without the beading and loosely install one bolt at the top to support the fender.
2. Now start the rest of the bolts. Tighten them just enough to hold the fender in position.Install a new rubber spacer washer between the fender and the running board, then install the bolt, washer and nut that attach the fender to the running board, but don't tighten yet.
3. Hold the new beading around the body immediately above the fender, and mark (with chalk) the locations of the bolts. Cut slots in the portion of the beading the extends down between the body and the fender to accomodate the bolts, then push the beading into place with your hand. Make sure the slots in the beading slip over the bolts. Be extremely careful about the fit of the beading as you gradually and evenly hand-tighten the fender bolts a few turns.
4. Gradually and evenly tighten all the bolts.
5. The remainder of installation is the reverse of removal. GOOD LUCK thanks
   

Rob Sinbad

• 709 Answers
• Posted on Jul 12, 2009

SOURCE: Need to replace passenger side front fender.

just used standard sockets with extenson, screw driver and phillips, remove head light and fender and fender guard cover. helper would really come in handy, so you dont scratch or drop fender.