Question about Pontiac Cars & Trucks

1 Answer

Update 2005 Pontiac vibe , giving faults codes p0351,p0352,p0353,p0354,replaced p0352 coil . car running great.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pontiac Master
  • 15,575 Answers

It may run fine but it's in fail safe mode
DTC P0351-P0354
DTCs P0351 through P0354 Ignition Coil Primary/Secondary Feedback Circuit diagnostic monitors the primary circuitry of individual ignition coils for the successful completion of an ignition event. The ignition trigger signal and ignition fail-safe input signal provide crucial information in the control of ignition system timing and the activation of the fail-safe function. Based on the initial timing angle, calculated from the crankshaft and the camshaft position signals, the powertrain control module (PCM) calculates the ignition trigger signal. The ignition trigger signal is then sent to the ignition control circuitry located in each ignition coil. The ignition control circuitry initiates the ignition dwell period by commanding the power transistor ON. When the PCM determines the proper time to provide spark, the PCM turns OFF the ignition trigger signal. In response to the PCM signal, the ignition coil control circuitry turns OFF the power transistor, producing a high voltage discharge from the secondary coil windings. After the spark has occurred, the control circuitry sends an ignition fail-safe input signal back to the PCM, confirming that an ignition event has taken place. If the ignition fail-safe input signal is not received by the PCM, a cylinder specific DTC will set.
Anytime the fail-safe input signal is lost, engine operation will enter the fail-safe function. If engine load exceeds certain parameters during the fail-safe function, Fuel Cut-off mode is activated and fuel injector operation is ceased. The suspension of fuel injection in the Fuel Cut-off mode protects the catalytic converter from damage. Damage can occur when excess unburned fuel reaches the converter and causes the catalyst to overheat.

Diagnostic Aids
• Check for the following conditions:
- An interruption of the ground circuit or voltage supply to the ignition coil will prevent a proper ignition event from taking place. A DTC P0351 through P0354 will set if there is a fault in any of the ignition coil circuits.
- If DTCs P0352, P0353, and P0354 are present, the fault is located in the shared electrical circuits or shared components of the ignition coils.
- Inspect the ignition coil grounds at G 105 for a clean and tight connection.
- The scan tool data parameters for Misfire Current Cylinder # are frozen at the time the MIL illuminates when the DTC sets.
- If no engine misfire is felt when the DTC sets, inspect for a fault in the Ignition Fail-Safe Input circuit.
- Inspect the noise filter for an internal short or low resistance. The ignition coil may not receive adequate voltage during high load conditions if the noise filter is faulty. A good noise filter will indicate infinite resistance (OL) with a DMM after the capacitor inside the filter is charged up.
- Unless the ignition key is cycled or the DTCs are cleared, the PCM waits to receive ignition fail-safe signals before providing fuel injector operation.
• An intermittent malfunction may be caused by a fault in the ignition coil electrical circuit. Inspect the wiring harness and the components for an intermittent condition. Refer to Intermittent Conditions .
• Repair any electrical circuit faults that were found. Refer to Wiring Repairs .
• The information included in the Freeze Frame data can be useful in determining the vehicle operating conditions when the DTC first set.

Posted on Dec 22, 2017

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 53745 Answers

SOURCE: 2005 Pontiac vibe fault p0351,p0352,p0353,p0354 , how do you fix it

all refer to the coils A,B,C,D===causes wiring, ignition coils ECM
for all to go out at once , I suspect a harness connection ot a failed ECM
substitute the ECM with a known good one to prove it before buying an ECM

Posted on Dec 20, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 ford fusion died and won't start but it will turn over. codes p0456,p0351,p0352,p0353 and p0354.


p0351,p0352,p0353 and p0354. It won't start because you have four cylinders not firing . P0351 - Ignition Coil A Primary/Secondary Circuit Description: See the description for DTC P0350. Possible Causes: See the possible causes for DTC P0350. Diagnostic Aids: See the diagnostic aids for DTC P0350. Application Key On Engine Off Key On Engine Running Continuous Memory Coil-on-plug (COP) ignition testing - GO to Pinpoint Test JF . GO to Pinpoint Test JF . Coil pack ignition testing - GO to Pinpoint Test JE . GO to Pinpoint Test JE .
When you see these codes , it's time to worry . These ford coil on plug system's can fry the transistors that control the coil firing . New computer or reman at ford $ 800.00 buck's then it needs to be programmed (dealer) What engine ? 3.0 v-6
This happens when the spark plug's are neglected , gap get's to wide , make's coil's over heat an break down , spark goes through the primary wire to the computer . Your best bet , take it to a qualified repair shop.

Jul 01, 2018 | Ford Cars & Trucks

1 Answer

2005 gmc envoy I have a codes p0351 p0352 p0353 p0354 p0355 and p0356


These codes ALL refer to the ignition coil of your car. Get your ignition system checked.

7c2c1eba-ce70-4439-a7d4-3846736326aa-qhqosp5ncgkcasye2ivvxzcr-2-0.jpeg

Feb 14, 2018 | GMC Cars & Trucks

1 Answer

2005 Pontiac vibe fault p0351,p0352,p0353,p0354 , how do you fix it


all refer to the coils A,B,C,D===causes wiring, ignition coils ECM
for all to go out at once , I suspect a harness connection ot a failed ECM
substitute the ECM with a known good one to prove it before buying an ECM

Dec 20, 2017 | Pontiac Cars & Trucks

1 Answer

2005 pontiac vibe fault cobes, p0351 p0352,p0353,p0354, how do you fix it


All those codes are the same BASIC code just for different coil pack secondary. You need to check the wiring from the coil packs and make sure they are all grounded properly. Corrosion or loose connection at a bus terminal can cause this. Here is a link: P0352 OBD II Trouble Code Ignition Coil Primary Secondary Circuit...

Dec 19, 2017 | Pontiac Cars & Trucks

1 Answer

01 Audi A6 p0351 p0352 and p0353


Look at fuel trim on a professional scanner

You still have the same codes for the same cylinder
misfires,IF the codes are correct

The misfires could come from valve issues,the valves themselves
or the variable cam actuators if that applies,or from fuel issues,but
not as likely on all three cyl on same bank

You need to do a cylinder leak down test on all cylinders--to eliminate mechanical issues

Then a cylinder contribution test electrically with scope software

Then scope the timing events,the cam advance events,the crank
position, all layered on the same screen & see if they line
up where they belong.

If the cams are not the issue, then your left with a serious vacuum
leak in the intake on one bank.

What I'm saying, is you have one bank with misfires apparently
not now from the ignition since the coils were replaced

Mar 19, 2014 | 2001 Audi A6

1 Answer

2007 Mercury Milan Premier V6 Misfiring


P0300 - Random multiple cylinder misfire
P0301 , 302 and 304 - Cyliners 1, 2 and 4 misfire
P0351 - Ignition coil A primary/secondary circuit malfunction
P0354 - Ignition coil D primary/secondary circuit malfunction

Nov 07, 2013 | Mercury Milan Cars & Trucks

1 Answer

I have a 2001 jeep grand cherokee and it giving me four code p1391 p0351 p0352 p0353 i will like to know the problem please


For some reason you question has been duplicated several times, so I will answer this one.
Code 1391 may be a problem with the ABS system, the other three codes are concerning the first 3 coils. Your engine has direct spark so each cylinder has its own coil.
I would clear the codes and see which ones come back after a test drive. If the three coil codes come back the coils would need to be tested.

Dec 19, 2012 | 2001 Jeep Grand Cherokee

1 Answer

Codes p0340 p0353 p0352 p0351 p1391


Kevin, can you give me a little more to work with? I would like year, make and model of your vehicle along with any other symtoms you may have experienced. Please get back to me with this information, and don't start replacing parts that you may not need. Waiting on your response.

Oct 18, 2011 | Cars & Trucks

1 Answer

2003 vw jetta gl 2.0 have codes p0351,p0352 and p0353


p0351- ignition coil A primary or secondary fault
p0352- ,, ,,,,,, ,,,,, B ,,,,, ,,,,,,, ,,,,,,,,,,,,, ,,,,,
p0353 - ,,,,,,,,,,,,, C,,,,,,,,,,,,,, ,,,, .,,,,,,,,,,,,,,,,
you may have a problem with yuor ingnition system

Sep 30, 2009 | 2003 Volkswagen Jetta TDI

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

Marvin
Marvin

Level 3 Expert

85020 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...