SOURCE: 2000 Chevy Blazer
i am working on a s 10 of the same yaer and problem i will post my results after tomorrow when i have finished the job i bout this truck cause of the forum i own one that is a great one and this one is for experimental purpose i will let u know so far you cant lift the motor with a jack or a hoist so we r going another route in the mornin
SOURCE: 2000 chevy impala ls -
You may have a lower intake manifold gasket leak (or a head gasket leak-slightly less probable) the lower intake can leak onto the serpentine belt and fling oil (and/or antifreeze). The lower intake manifold gasket is usually the culprit here. There is much information about changing it if you are inclined to do it yourself. If not, expect around 800 to 1200 to fix at dealer/mechanic. This is usually accompanied by (but not always) oil in the antifreeze, or antifreeze in the oil...
SOURCE: need to change oil pan
e
Cavalier, Sunfire 2001-2005
Oil Pan - Removal & Installation
2.2L (VIN 4) Engine
To install:
Negative battery cable
Right front wheel
Right inner fender splash shield
Starter motor and bracket
Engine mount strut bracket
Oil pan
Fig. Exploded view of the oil pan mounting and related components-2.2L (VIN 4) engine
2.2L (VIN F) Engine
Oil pan with a new gasket. Torque the nuts and bolts to 89 inch lbs. (10 Nm).
Engine mount strut bracket. Torque the bolts to 49 ft. lbs. (66 Nm).
Starter motor and bracket. Torque the bolts to 37 ft. lbs. (50 Nm).
Right fender splash shield
Right front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).
Negative battery cable
To install:
Engine mount strut bracket
Drive belt
Lower then upper AC compressor bolts
Oil pan bolts
Oil pan
Fig. Remove/Install the oil pan bolts in this sequence-2.2L (VIN F) engine
Oil pan and tighten the bolts to 18 ft. lbs. (25 Nm)
AC compressor bolts
Engine mount bracket
Drive belt
2.4L Engine
To install:
Negative battery cable
Flywheel/converter cover
Right wheel
Right wheel well splash shield
Accessory drive belt
Air conditioning compressor lower bolts
Transmission-to-engine brace
Engine mount strut bracket
Radiator outlet pipe bolts
Radiator outlet pipe from the oil pan
Oil pan to the flywheel cover bolt and nut
Flywheel cover stud for clearance
Radiator outlet pipe from the lower radiator hose and oil pan
Oil level sensor connector
Oil pan
Oil pan with the gasket. Torque the M8 bolts to 18 ft. lbs. (24 Nm) and the M6 bolts to 106 inch lbs. (12 Nm).
Fig. Oil pan fastener torque specifications-2.4L engine
Oil pan to the transmission nut
Oil level sensor connector
Radiator outlet pipe to the lower radiator hose and oil pan
Exhaust manifold brace
Radiator outlet pipe. Torque the bolts to 124 inch lbs. (14 Nm).
Engine mount strut bracket. Torque the bolts to 55 ft. lbs. (75 Nm).
Transmission to the engine brace
Air conditioning compressor lower bolts. Torque the bolts to 37 ft. lbs. (50 Nm).
Accessory drive belt
Right splash shield
Right front wheel
Flywheel/converter cover
Negative battery cable
Hope helped (remember rated this help). Good luck.
SOURCE: removing starter from a 2000 3.4 chevy impala? I
try sliding it backwards and let the nose fall first, may require pressure but it should work
370 views
Usually answered in minutes!
Hi David Stancil, I want to help you with your question, but I need more information from you. Can you please add details in the comment box?
×