Question about Ford Cars & Trucks

2 Answers

Hi ,I'm currently rebuilding a Ford 1.0 ecoboost engine , I'm looking for the tightening torque settings for the main bearings and big end bearings , Help would be most appreciated.

Engine from a 2013 Ford c max

Posted by on

  • Sheraaz Suliman
    Sheraaz Suliman Jan 23, 2019

    Hi Derek
    I know your post was in nov 2017 but did you find the torque settings? if so pls could you let me know them.

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 1 Answer

Hi Derek any luck on this as I am also considering rebuild my engine as the big ends went found a crankshaft and bearing but no torque specs ???
checked on automata and it says don't not dismantle the lower part of engine ?
when I spoke to fords they only sell a short block funny that

Posted on Aug 10, 2018

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 21,128 Answers

Find and buy the service manual

Posted on Aug 08, 2018

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

stevenhurc
  • 450 Answers

SOURCE: torque specs for big ends, mains, cam caps

found local Adelaide engine reconditioning shop that knows all about g200 twin cam EFI isuzu motors for parts and engine components ( pistons, rings, bearings etc. ) and machining, Chris Milton engine reconditioning. They will do machine work for me so then i can put it together.

Posted on May 27, 2009

michael_grey
  • 365 Answers

SOURCE: engine bearing torque settings big end and main bearing

4 cylinder correct?
1bac25a.jpg

Posted on Jun 20, 2009

  • 167 Answers

SOURCE: WOULD YOU KNOW THE TORQUE SETTINGS FOR MAIN

Mains Stage 1 83nm
Mains Stage 2 167nm

Big ends Stage 1 29nm
Big ends Stage 2 45 - 60 degrees

Hope this helps

Posted on Jul 10, 2009

  • 115 Answers

SOURCE: cylinder head torque settings for a toyota 1493cc

If you have a vehicle application for the motor you can get a Haynes or Chilton manual from your local auto parts store. They usual run around $30.

Posted on Sep 04, 2009

  • 1 Answer

SOURCE: i need to know the torque settings for 850cc reliant robin

go to
http://mankymonkeymotors.co.uk/Trikespageimages/relianttorquesettings.html

a target="_new" href="http://www.leafletflyers.co.uk/">Leaflet Distribution in Croydon</a>, Leaflet Distribution in Balham, <a target="_new" href="http://leafletflyers.co.uk/Leaflet-Distribution-Streatham.htm">Leaflet Distribution Streatham</a>.

Posted on Aug 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi their can some assist with the torque setting on a ford fiesta 1.4 duratec 2004 on the main bearing and big end


Your better off buying a decent workshop manual, like a Haynes manual. Those bolts use two different settings to tighten them. You first use a torque setting then you use an angular torque gauge to turn the bolt an extra fixed number of degrees. Setting them wrong could blow the entire engine.

Dec 26, 2017 | Ford Cars & Trucks

1 Answer

Torque settings on a yaris 1.3 16v big ends,mains,flywheel,cylinderhead


Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

Jul 15, 2016 | 2007 Toyota Yaris

1 Answer

Hi i have daewoo matiz 800cc can you help me by giving me the torque settings for the big end bearing caps please


You are looking for the torque settings for big end bearings and main bearings on a daewoo matiz?
Main bearings torques on a Daewoo Matiz 800cc (1999)
Stage 1: 25-30 Nm
Stage 2: 55-60 Nm
Big End Bearings…

Mar 09, 2016 | Daewoo Cars & Trucks

1 Answer

What is the torque setting for main bearing and big end bearing of a Toyota Yaris 1.0 1kr 3 cylinder?


Toyota Yaris Main and Big end Torques:
Tighten the main and big end bolts in sequential order and in steps two steps.
- Main bearings. Stage 1. 30 Nm.
Stage 2. 59 Nm.
- Big end bearings. Stage 1. 15 Nm.
Rotate further by 90 degrees.

Apr 09, 2015 | 2008 Toyota Yaris

1 Answer

What the torque settling on a 1.8spi vauxhall cavalier 1994


Cylinder head Renew bolts: Yes Tighten: 25 Nm Tighten: 90° Tighten: 90° Tighten: 90° Other engine tightening torques Main bearings Renew bolts/nuts: Yes Main bearings Stage 1: 50 Nm Main bearings Stage 2: 45°-60° Big end bearings Renew bolts/nuts: Yes Big end bearings Stage 1: 35 Nm Big end bearings Stage 2: 45°-60° Oil pump to cylinder block : 6 Nm Sump bolts : 15 Nm Sump drain bolt : 55 Nm Flywheel/driveplate :
  • Use new bolts and tighten as follows:
      • 1,4/1,6 = 35 Nm + 30° + 15°
      • 1,8/2,0 = 65 Nm + 30° + 15°
  • "Pot"-type flywheel = 65 Nm + 30° + 15°
  • Tighten drive plate to 60 Nm.
Clutch pressure plate : 15 Nm Crankshaft pulley/damper centre bolt : Use new bolts. Tighten centre bolt to 130 Nm + 40°-50°
Camshaft sprocket/gear : 45 Nm Camshaft/rocker cover : 8 Nm Inlet manifold to cylinder head : 22 Nm Exhaust manifold to cylinder head : 22 Nm Spark plugs : 25 Nm Lambda sensor (Oxygen) : 30 Nm Chassis tightening torques Front hub :
  • Tighten nut in three stages:
    1. 130 Nm
    2. Slacken off
    3. 20 Nm + 80°-90°.
Steering track rod end : New nuts 60 Nm Brake disc to hub Front: 4 Nm Brake caliper to carrier Front: 30 Nm Brake caliper/carrier to hub Front: 95 Nm Brake caliper/carrier to hub Rear: 80 Nm New bolts ABS sensor Front: 8 Nm ABS sensor Rear: 15 Nm Road wheels : 110 Nm
There you go pretty much covers everything hope that helps

Jan 11, 2015 | Vauxhall Cars & Trucks

1 Answer

Hi I need the torque settings for both the cylinder head and the bottom end bearings for a 1997 Toyota Prado (3.4litre petrol). Thanks


1997 Toyota Prado 5VZ-FE
Cylinder head bolts:

Tighten the cylinder head bolts in criss cross manner inside out, in four stages as under:
Stage 1. Torque the bolts up to 17 Nm.
Stage 2. 34 Nm.
Stage 3. Rotate all the bolts 90 degrees.
Stage 4. Finally rotate all the bolts further 90 degrees.

Main Bearings:
Tighten the main bearing bolts in two stages, as under:
Stage 1. 61 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Big end bearings:
Tighten the big end bolt of connecting rods in two stages as under:
Stage 1. 25 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Feb 27, 2014 | Toyota Land Cruiser Cars & Trucks

1 Answer

Replace crankshaft bearings on 1999 ford expedition


v6 have 4 main bearing sets and 6 big end bearing sets
v8 have 5 main bearing sets and 8 bigend sets
5 cylinder inline will have 6 main bearing sets and 5 big end set
It appears that some where you are short a set of bearings Check that the rebuild kit is for your engine

Feb 22, 2013 | Ford Cars & Trucks

2 Answers

I need the torque specs for the main and rod bolt for a 99 escort 2.0l engine


engine tightening torques
Main bearings Renew bolts/nuts No
Main bearings Stage 1 43 Nm
Main bearings Stage 2 85 Nm
Big end bearings Renew bolts/nuts Yes
Big end bearings Stage 1 15 Nm
Big end bearings Stage 2 90°

Jan 21, 2010 | 2004 Ford Focus

2 Answers

WOULD YOU KNOW THE TORQUE SETTINGS FOR MAIN BEARING AND BIG END BEARING CAPS FOR ISUZU 4JG2 ENGINE


Mains Stage 1 83nm
Mains Stage 2 167nm

Big ends Stage 1 29nm
Big ends Stage 2 45 - 60 degrees

Hope this helps

Jul 10, 2009 | 1994 Isuzu Trooper

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

299 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

83959 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22441 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...