2004 Lexus es330 intake manifold torque sequence.need to reinstall intake manifold after replacing the knock sensors. Need torque in ft. lbs. and bolt sequence. Thank you!

Nissan Frontier, Xterra 1998-05

• MAIN BEARING TORQUE SEQUENCE

Torque Specifications

Fig.
TORQUE SPECIFICATIONS
all readings in ft. lbs. Year Engine Displacement Liters (cc) Engine ID/VIN Cylinder Head Bolts Main Bearing Bolts Rod Brearing Bolts Crankshaft Damper Bolts Flywheel Bolts Manifold Spark Plugs Lug Nuts Intake Exhaust 1998 2.4 (2389) KA24DE
1A Step 1: 22 ft. lbs.
2B 10-12 ft. lbs. plus 60-65 degrees or 28-33 ft. lbs.
3
4C The cylinder heads and the lower intake manifold are installed together
TORQUE SPECIFICATIONS
all readings in ft. lbs. Year Engine Displacement Liters (cc) Engine ID/VIN Cylinder Head Bolts Main Bearing Bolts Rod Brearing Bolts Crankshaft Damper Bolts Flywheel Bolts Manifold Spark Plugs Lug Nuts Intake Exhaust 1999 2.4 (2389) KA24DE 3.3 (3277) VG33E
1A Step 1: 22 ft. lbs.
2B 10-12 ft. lbs. plus 60-65 degrees or 28-33 ft. lbs.
3
4C The cylinder heads and the lower intake manifold are installed together
TORQUE SPECIFICATIONS
all readings in ft. lbs. Year Engine Displacement Liters (cc) Engine ID/VIN Cylinder Head Bolts Main Bearing Bolts Rod Brearing Bolts Crankshaft Damper Bolts Flywheel Bolts Manifold Spark Plugs Lug Nuts Intake Exhaust 2000 2.4 (2389) KA24DE 3.3 (3277) VG33E
1A Step 1: 22 ft. lbs.
2B 10-12 ft. lbs. plus 60-65 degrees or 28-33 ft. lbs.
3
4C The cylinder heads and the lower intake manifold are installed together
TORQUE SPECIFICATIONS
all readings in ft. lbs. Year Engine Displacement Liters (cc) Engine ID/VIN Cylinder Head Bolts Main Bearing Bolts Rod Brearing Bolts Crankshaft Damper Bolts Flywheel Bolts Manifold Spark Plugs Lug Nuts Intake Exhaust 2000 3.3 (3277) VG33E
1A The cylinder heads and the lower intake manifold are installed together
2B 10-12 ft. lbs. plus 60-65 degrees or 28-33 ft. lbs.
3C Step 1: Tighten the cylinder head bolts to 22 ft. lbs.
4D Step 1: Tighten the connecting rod bearing bolts to 10-12 ft. lbs.
TORQUE SPECIFICATIONS
all readings in ft. lbs. Year Engine ID Engine Displacement Liters Cylinder Head Bolts Main Bearing Bolts Rod Bearing Bolts Crankshaft Damper Bolts Flywheel Bolts Manifold Spark Plugs Oil Pan Drain Plug Intake Exhaust 1998 KA24DE
1- Step 1: 22 ft. lbs.
2- 10-12 ft. lbs. plus 60-65 degrees or 28-33 ft. lbs.
3- The cylinder heads and the lower intake manifold are installed together
4- 10-12 ft. lbs. +60-65 degrees
5- Step 1: 72 ft. lbs.
6- Step 1: bolts 11-22 19 ft. lbs.
7- Step 1: 20 ft. lbs.
8- Step 1: 31 ft. lbs.
9- 83 inch lbs.
10- Stud bolt: 11 ft. lbs.
11- Step 1: 72 ft. lbs.
12- Bolts: 17-24 (M8) 16 ft. lbs.
13- Step 1: 33 ft. lbs.
14- Intake manifold collector:
15- Intake manifold:
TORQUE SPECIFICATIONS
all readings in ft. lbs. Year Engine ID Engine Displacement Liters Cylinder Head Bolts Main Bearing Bolts Rod Bearing Bolts Crankshaft Damper Bolts Flywheel Bolts Manifold Spark Plugs Oil Pan Drain Plug Intake Exhaust 1999 KA24DE VG33E
1- Step 1: 22 ft. lbs.
2- 10-12 ft. lbs. plus 60-65 degrees or 28-33 ft. lbs.
3- The cylinder heads and the lower intake manifold are installed together
4- 10-12 ft. lbs. +60-65 degrees
5- Step 1: 72 ft. lbs.
6- Step 1: bolts 11-22 19 ft. lbs.
7- Step 1: 20 ft. lbs.
8- Step 1: 31 ft. lbs.
9- 83 inch lbs.
10- Stud bolt: 11 ft. lbs.
11- Step 1: 72 ft. lbs.
12- Bolts: 17-24 (M8) 16 ft. lbs.
13- Step 1: 33 ft. lbs.
14- Intake manifold collector:
15- Intake manifold:
TORQUE SPECIFICATIONS
all readings in ft. lbs. Year Engine ID Engine Displacement Liters Cylinder Head Bolts Main Bearing Bolts Rod Bearing Bolts Crankshaft Damper Bolts Flywheel Bolts Manifold Spark Plugs Oil Pan Drain Plug Intake Exhaust 2000 KA24DE VG33E
1- Step 1: 22 ft. lbs.
2- 10-12 ft. lbs. plus 60-65 degrees or 28-33 ft. lbs.
3- The cylinder heads and the lower intake manifold are installed together
4- 10-12 ft. lbs. +60-65 degrees
5- Step 1: 72 ft. lbs.
6- Step 1: bolts 11-22 19 ft. lbs.
7- Step 1: 20 ft. lbs.
8- Step 1: 31 ft. lbs.
9- 83 inch lbs.
10- Stud bolt: 11 ft. lbs.
11- Step 1: 72 ft. lbs.
12- Bolts: 17-24 (M8) 16 ft. lbs.
13- Step 1: 33 ft. lbs.
14- Intake manifold collector:
15- Intake manifold:
TORQUE SPECIFICATIONS
all readings in ft. lbs. Year Engine ID Engine Displacement Liters Cylinder Head Bolts Main Bearing Bolts Rod Bearing Bolts Crankshaft Damper Bolts Flywheel Bolts Manifold Spark Plugs Oil Pan Drain Plug Intake Exhaust 2001 KA24DE VG33E
1- Step 1: 22 ft. lbs.
2- 10-12 ft. lbs. plus 60-65 degrees or 28-33 ft. lbs.
3- The cylinder heads and the lower intake manifold are installed together
4- 10-12 ft. lbs. +60-65 degrees
5- Step 1: 72 ft. lbs.
6- Step 1: bolts 11-22 19 ft. lbs.
7- Step 1: 20 ft. lbs.
8- Step 1: 31 ft. lbs.
9- 83 inch lbs.
10- Stud bolt: 11 ft. lbs.
11- Step 1: 72 ft. lbs.
12- Bolts: 17-24 (M8) 16 ft. lbs.
13- Step 1: 33 ft. lbs.
14- Intake manifold collector:
15- Intake manifold:
TORQUE SPECIFICATIONS
all readings in ft. lbs. Year Engine ID Engine Displacement Liters Cylinder Head Bolts Main Bearing Bolts Rod Bearing Bolts Crankshaft Damper Bolts Flywheel Bolts Manifold Spark Plugs Oil Pan Drain Plug Intake Exhaust 2002 KA24DE VG33E VG33ER
1- Step 1: 22 ft. lbs.
2- 10-12 ft. lbs. plus 60-65 degrees or 28-33 ft. lbs.
3- The cylinder heads and the lower intake manifold are installed together
4- 10-12 ft. lbs. +60-65 degrees
5- Step 1: 72 ft. lbs.
6- Step 1: bolts 11-22 19 ft. lbs.
7- Step 1: 20 ft. lbs.
8- Step 1: 31 ft. lbs.
9- 83 inch lbs.
10- Stud bolt: 11 ft. lbs.
11- Step 1: 72 ft. lbs.
12- Bolts: 17-24 (M8) 16 ft. lbs.
13- Step 1: 33 ft. lbs.
14- Intake manifold collector:
15- Intake manifold:
TORQUE SPECIFICATIONS
all readings in ft. lbs. Year Engine ID Engine Displacement Liters Cylinder Head Bolts Main Bearing Bolts Rod Bearing Bolts Crankshaft Damper Bolts Flywheel Bolts Manifold Spark Plugs Oil Pan Drain Plug Intake Exhaust 2003 KA24DE VG33E VG33ER
1- Step 1: 22 ft. lbs.
2- 10-12 ft. lbs. plus 60-65 degrees or 28-33 ft. lbs.
3- The cylinder heads and the lower intake manifold are installed together
4- 10-12 ft. lbs. +60-65 degrees
5- Step 1: 72 ft. lbs.
6- Step 1: bolts 11-22 19 ft. lbs.
7- Step 1: 20 ft. lbs.
8- Step 1: 31 ft. lbs.
9- 83 inch lbs.
10- Stud bolt: 11 ft. lbs.
11- Step 1: 72 ft. lbs.
12- Bolts: 17-24 (M8) 16 ft. lbs.
13- Step 1: 33 ft. lbs.
14- Intake manifold collector:
15- Intake manifold:
TORQUE SPECIFICATIONS
all readings in ft. lbs. Year Engine ID Engine Displacement Liters Cylinder Head Bolts Main Bearing Bolts Rod Bearing Bolts Crankshaft Damper Bolts Flywheel Bolts Manifold Spark Plugs Oil Pan Drain Plug Intake Exhaust 2004 KA24DE VG33E VG33ER
1- Step 1: 22 ft. lbs.
2- 10-12 ft. lbs. plus 60-65 degrees or 28-33 ft. lbs.
3- The cylinder heads and the lower intake manifold are installed together
4- 10-12 ft. lbs. +60-65 degrees
5- Step 1: 72 ft. lbs.
6- Step 1: bolts 11-22 19 ft. lbs.
7- Step 1: 20 ft. lbs.
8- Step 1: 31 ft. lbs.
9- 83 inch lbs.
10- Stud bolt: 11 ft. lbs.
11- Step 1: 72 ft. lbs.
12- Bolts: 17-24 (M8) 16 ft. lbs.
13- Step 1: 33 ft. lbs.
14- Intake manifold collector:
15- Intake manifold:
TORQUE SPECIFICATIONS
all readings in ft. lbs. Year Engine ID Engine Displacement Liters Cylinder Head Bolts Main Bearing Bolts Rod Bearing Bolts Crankshaft Damper Bolts Flywheel Bolts Manifold Spark Plugs Oil Pan Drain Plug Intake Exhaust 2005 QR25DE VQ40DE
1- Step 1: 22 ft. lbs.
2- 10-12 ft. lbs. plus 60-65 degrees or 28-33 ft. lbs.
3- The cylinder heads and the lower intake manifold are installed together
4- 10-12 ft. lbs. +60-65 degrees
5- Step 1: 72 ft. lbs.
6- Step 1: bolts 11-22 19 ft. lbs.
7- Step 1: 20 ft. lbs.
8- Step 1: 31 ft. lbs.
9- 83 inch lbs.
10- Stud bolt: 11 ft. lbs.
11- Step 1: 72 ft. lbs.
12- Bolts: 17-24 (M8) 16 ft. lbs.
13- Step 1: 33 ft. lbs.
14- Intake manifold collector:
15- Intake manifold:
Main Bearing Torque Sequence




Fig. Main bearing torque sequence-2.4L engine



Fig. Main bearing torque sequence-2.5L engine



Fig. Main bearing torque sequence-3.3L engine



Fig. Main bearing torque sequence-4.0L engine

Pretend the picture is lower intake manifold, that is the tightening sequence.
1st step 5 ft lbs
2nd step bolts 1--4 9.6 ft lbs
3rd step bolts 5--8 18 ft lbs
The upper intake manifold use about the same sequence tighten to 18 ft lbs.
If you don't like ft lbs use inch lbs.
If the upper intake manifold is plastic, be careful with that.

V8 Engines Component Torque Camshaft Sprocket Bolt 40-45 ft. lbs. Camshaft Thrust Plate-to-Engine Bolts 9-12 ft. lbs. Crankshaft Pulley-to-
Vibration Damper Bolts 35-50 ft. lbs. Cylinder Head Bolts All Except 1993 Flanged Bolts Step 1 55-65 ft. lbs. Step 2 65-72 ft. lbs. 1993 Flanged Bolts NOTE 1 Exhaust Manifold Bolts All Except 1993 HO Cobra 18-24 ft. lbs. 1993 HO Cobra 26-32 ft. lbs. Flywheel/Driveplate-to-
Crankshaft Bolts 75-85 ft. lbs. Intake Manifold Bolts Note 2 Upper Intake Manifold-to-
Intake Manifold Bolts 12-18 ft. lbs. Main Bearing Cap Bolts 60-70 ft. lbs. Oil Filter Insert-to-Engine Adapter Bolt 20-30 ft. lbs. Oil Pan 1979 Step1 Large Bolts 11-13 ft. lbs. Small Bolts 7-9 ft. lbs. Step 2 Large Bolts 15-17 ft. lbs. Small Bolts 10-12 ft. lbs. 1980-87 9-11 ft. lbs. 1988 and up 6-9 ft. lbs. Oil Pick-up Tube-to-Main Bearing Cap Nut 22-32 ft. lbs. Oil Pick-up Tube-to-Oil Pump Bolts 1979-87 10-15 ft. lbs. 1988 and up 12-18 ft. lbs. Oil Pump Bolts 22-32 ft. lbs. Rocker Arm Fulcrum Bolts 18-25 ft. lbs. Thermostat Housing-to-Engine Bolts Through 1987 9-12 ft. lbs. 1988 and up 12-18 ft. lbs. Timing Chain Cover Bolts 12-18 ft. lbs. Valve Cover Bolts 10-13 ft. lbs. Water Pump Mounting Bolts 12-18 ft. lbs. NOTE 1 Step 1 Tighten bolts in sequence to 25-35 ft. lbs. Step 2 Tighten bolts in sequence to 45-55 ft. lbs. Step 3 Tighten bolts in sequence an additional ¼ turn. NOTE 2 Step 1 Tighten bolts in sequence to 23-25 ft. lbs. Step 2 After assembly, retorque all bolts in sequence to 23-25 ft. lbs.let me know if this helps and how about a rating.

Please don't forget to rate. Thank you:

Left side front cylinder head



Cylinder head bolt torque sequence-3.4L engine

Cylinder head by aligning it with the dowel pins

New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.

Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).

Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).

Right side rear cylinder head:



Cylinder head bolt torque sequence-3.4L engine

New cylinder head gasket

Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins

New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.

Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).

Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).

Spark plug wires

Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).

Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.

Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).

Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).

Bonneville, LeSabre, Park Avenue 2000-2005 Intake Manifold - Removal & Installation

3.8L Engine
VIN 1 Engine

1. Before servicing the vehicle, refer to the Precautions section.
2. Relieve the fuel system pressure.
3. Drain the cooling system.
4. Remove or disconnect the following:
   Negative battery cable Supercharger Thermostat housing Exhaust Gas Recirculation (EGR) tube at the intake manifold Engine Control Temperature (ECT) sensor Intake manifold

To install:

1. Install or connect the following:
   Intake manifold with new gaskets. Torque the bolts, working from the center out, to 11 ft. lbs. (15 Nm). ECT sensor connector EGR tube to the intake manifold Thermostat housing Supercharger Negative battery cable
2. Refill and bleed the cooling system.
3. Run the engine and check for leaks and proper engine operation.

VIN K Engine

1. Before servicing the vehicle, refer to the Precautions section.
2. Disconnect the negative battery cable.
3. Drain the cooling system.
4. Relieve the fuel system pressure.
5. Remove or disconnect the following:
   Fuel injector sight shield Air inlet duct Spark plug wires from the right side Manifold Absolute Pressure (MAP) sensor Vacuum lines from the intake manifold Fuel lines Fuel injector electrical connectors Fuel regulator vacuum line Fuel rail from the intake manifold Exhaust Gas Recirculation (EGR) heat shield Throttle cable bracket from the cylinder head mounting bracket and the throttle body cables Throttle body support bracket Upper intake plenum and gasket Thermostat housing Electrical connector from the Engine Coolant Temperature (ECT) sensor Drive belt tensioner assembly EGR valve outlet pipe Lower intake manifold
   
   
   Fig. Exploded view of the intake manifold and related components-3.8L (VIN K) engine
   

To install:



Fig. Upper intake manifold torque sequence-3.8L (VIN K) engine



Fig. Lower intake manifold torque sequence-3.8L (VIN K) engine

1. Install or connect the following:
   Intake manifold using new manifold gaskets. Torque the bolts in sequence to 11 ft. lbs. (15 Nm); then, re-torque to 11 ft. lbs. (15 Nm). EGR valve outlet pipe Drive belt tensioner assembly. Torque the tensioner bolts to 37 ft. lbs. (50 Nm). Electrical connector to the ECT sensor Thermostat housing Upper intake plenum. Torque the intake plenum bolts to 88 inch. lbs. (10 Nm). Throttle body support bracket Throttle cable bracket to the cylinder head mounting bracket and the cables to the throttle body lever EGR heat shield Fuel rail. Torque the fuel rail bolts to 88 inch. lbs. (10 Nm). Fuel lines Fuel regulator vacuum line Fuel injector electrical connectors Vacuum lines to the intake manifold MAP sensor Spark plug wires Fuel injector sight shield and air inlet duct Negative battery cable
2. Refill and bleed the cooling system.
3. Run the engine and check for leaks and proper engine operation.

Hope this help (remember rated this).

Please don't forget to rate. Thank you:

Left side front cylinder head



Cylinder head bolt torque sequence—3.4L engine

Cylinder head by aligning it with the dowel pins

New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.

Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).

Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).

Right side rear cylinder head:



Cylinder head bolt torque sequence—3.4L engine

New cylinder head gasket

Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins

New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.

Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).

Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).

Spark plug wires

Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).

Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.

Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).

Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).

Cylinder Head Bolt Step1- (25 FT.Lbs) Step2(45 Ft.Lbs) Step3(65Ft,Lbs).....Intake Manifold(35Ft Lbs)....Exhaust Manifold Center (20Ft Lbs) All Others (20 Ftlbs).....Thanks

2.2L (VIN 4) Engine

1. Before servicing the vehicle, refer to the precautions section.
   
2. Relieve the fuel system pressure.
   
3. Drain the cooling system.
   
4. Remove or disconnect the following:
   
   • Accessory drive belt
     
   • Air cleaner outlet duct
     
   • Engine mount
     
   • Intake manifold
     
   • Exhaust manifold
     
   • Engine Coolant Temperature (ECT) sensor electrical connector
     
   • Power steering pump
     
   • Radiator inlet pipe
     
   • Spark plug wires
     
   • Rocker arm cover
     
   
   NOTE Whenever valve train components are removed, keep them in order for installation purposes.
   
   
   • Rocker arms and pushrods
     
   • Lifters
     
   • Alternator rear brace and the alternator
     
   • Power steering pump
     
   • Radiator inlet pipe
     
   • Ignition coil assembly
     
   • Accessory bracket
     
   • Spark plug wires
     
   • Cylinder head bolts
     
   
   WARNING Two sizes of bolts are used; note the location of each.
   
   
   • Cylinder head
     
5. Inspect the cylinder head and block surface for cracks, nicks, heavy scratches and flatness.
   

Cylinder head torquing sequence—2.2L (VIN 4) engine

1. Install or connect the following:
   
   • Cylinder head with a new gasket and new cylinder head bolts. Torque the long bolts, in sequence to 46 ft. lbs. (63 Nm) and the short bolts to 43 ft. lbs. (58 Nm) plus an additional 90 degree turn on all the bolts.
     
   • Lifters
     
   • Pushrods and rocker arms. Torque nuts to 22 ft. lbs. (30 Nm).
     
   • Rocker arm cover. Torque the bolts to 89 inch lbs. (10 Nm).
     
   • Spark plug wires
     
   • Accessory bracket
     
   • Ignition coil assembly
     
   • Radiator inlet pipe
     
   • Power steering pump. Torque the bolts to 22 ft. lbs. (30 Nm).
     
   • ECT sensor electrical connector
     
   • Exhaust manifold. Torque the nuts to 118 inch lbs. (13 Nm).
     
   • Alternator. Torque the bolts to 37 ft. lbs. (50 Nm).
     
   • Intake manifold. Torque the bolts to 17 ft. lbs. (24 Nm).
     
   • Engine mount. Torque the bolts to 55 ft. lbs. (75 Nm).
     
   • Air cleaner outlet duct
     
   • Accessory drive belt
     
   • Negative battery cable
     
2. Refill and bleed the cooling system.
   
3. Start the vehicle and inspect for leaks.
   

Head Torque sequence Step 1: torque to 50 Ft/Lbs Step 2: torque to 105 Ft/Lbs recheck final torque in sequence.

Torque intake manifold: Step 1: 12 inch/Lbs, (hand tight) Step 2: 72 inch/Lbs, (6) Ft/Lbs Step 3: 12 Ft/Lbs
torque intake plenum: Step 1: 24 inch/lb (hand tight) Step 2: 48 inch/lb (4) Ft/Lbs Step 3: 84 inch/lb (7) Ft/Lbs (To torque bolts, start in center using crisscross pattern)