Question about 2003 Hyundai Tiburon

Open Question

How do i Remove the rear rotor on a 2003 hyundai tiburon?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 114 Answers

SOURCE: 2003 tiburon transmission

if you have a 4 cylinder you wiggle the clutch shaft up and down remove the lever and this will get the fingers off the releasbearing / 2 starter bolts 2 large bolts up top 3 under exhaust and 4 0n the other side lower one is above right inner cv axle, remove left axle from car right axle can moved over un do ball joint 3 mounts remover upper side and reaar , strap engine to a cradle or 4,4 post chained to support engine you can slide tranmission over14 inches with room to stick your hands in and remove pressure plate ,fly wheel can be removed but takes good hands tricky,now thats a hyundai flat rate tech procedure for 4 cyl, IF YOUR NOT SURE ABOUT or if the engine is V6 cylinder THE SUB FRAME COMES OUT you can remove rack hose on sub frame and 4 bolts and wire or strap the steering rack to body at that can stay in car or you will have to take rack out with sub frame

Posted on Sep 25, 2008

Ad
alicantecoli
  • 22484 Answers

SOURCE: 2003 hyundai tiburon alarm system

factory fitted alarm?? no way its done through the ECU and shuts down the spark via the processor and try finding a wiring diagram??

Posted on Feb 09, 2009

ghost4548
  • 776 Answers

SOURCE: Location of the Purge Control Valve for 2003 Hyundai Tiburon

There were two different engines which were installed in the 2003 Tiberon... the 2.0 liter 4 cylinder:
22c99c7.jpg

And the 2.7 Liter V6:
cb31feb.jpg

Posted on Jun 06, 2009

ghost4548
  • 776 Answers

SOURCE: Need Instructions on 2003 Hyundai Tiburon Clutch Replacement

Go to http://www.hmaservice.com/ and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about your vehicle.

Posted on Jun 14, 2009

  • 1 Answer

SOURCE: 2003 Hyundia Tiburon BCM

http://www.newtiburon.com/forums/showthread.php?t=102241&highlight=bcm

Posted on Jun 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hyundai Tiburon 03 rear motor wind shield wiper is located ?


The motor is located inside the rear hatch, you must remove the trim panel.

Feb 08, 2012 | 2003 Hyundai Tiburon

1 Answer

I have a 2003 tiburon and I changed the rear rotors and pads but can't seem to get the caliper back on cause the lower guide pin doesn't slide like the upper one. I have never seen this before is...


YOU NEED TO COMPRESS THE CALIPER PISTON USING SPECIAL TOOL 09580 - 3400 OR YOU CAN USE A LARGE C CLAMP AND THE OLD BRAKE SHOE NEXT TO CALIPER PISTON.BE SURE TO SIPHON OUT 1/3 BRAKE FLUID OUT OF THE MASTER CYLINDER BEFORE COMPRESSING CALIPER PISTON BACK IN THE CALIPER BORE.WHEN YOU FINISH REPLACING REPLACING REAR BRAKE SHOES.MAKE SURE BRAKE MASTERCYLINDER RESERVOIR COVER BACK ON RESERVOIR BACK IN PLACE.THEN PUMP BRAKE PEDAL TO SEAT BRAKE SHOES AGAINST ROTORS AND UNTIL YOU GET FIRM SOLID BRAKES.THEN CHECK BRAKE FLUID LEVEL.DONT DRIVE CAR IF BRAKE PEDAL FEEL SOFT NOT FIRM.CHECK FOR LEAKING BRAKE HOSE OR LEAKING CALIPER PISTON SEAL.

May 08, 2011 | 2003 Hyundai Tiburon

1 Answer

How di i remove rear side windows in tact


window fitters use a bent knife to cut the sealant around the window ,apply too much pressure and it will pop.

Mar 08, 2010 | 2003 Hyundai Tiburon

1 Answer

Change a tail light 2003 hyundai tiburon


there are 3 8mm nuts holding them on. you have to remove some of the trunk trim to access them. on some models you have to remove the sub.

Aug 28, 2009 | 2003 Hyundai Tiburon

1 Answer

What does it take to replace the front wheel bearings on a 2003 Tiburon


the front wheel bearings on your car are not sold except as a front wheel hub assembly with the bearing pre-installed, they run about $100.00 each, to replace them requires no special tools, all u do is remove the wheel, the brake caliper and the brake rotor and the hub nut, then the hub just slides off, u will most likely need a very large socket for the hub retaining nut.

Jul 05, 2009 | 2003 Hyundai Tiburon

1 Answer

How do i change the back brakes on a 2006 tiburon


Disk Brakes - remove two 14mm bolts which mount the caliper to the rear hub assy. Remove the caliper. Remove the phillips screw which holds the rotor to the hub. Machine the rotor and reinstall on the hub & reinstall the phillips screw. Reinstall the caliper and remove one of the caliper hinge pin (sliding pin) 14mm bolts. Flip the caliper out of the way and replace the pads and anti-rattle springs. Recompress the caliper piston all the way back into its cylinder. Flip the caliper back into position and reinstall the 14mm bolts. Of course, you need to purchase the replacement pads and w/anti-rattle springs.

Jun 29, 2009 | 2006 Hyundai Tiburon

2 Answers

Can not get the rotors off my 97 hyundai tibaron


Hyundai Tiburon 96-01 uses a outer hub system. To replace front rotors. You'll need front bearings as well. The bearing and hub will need to be pressed out of the spindal. Then replacement of bearing will need to be pressed in. From a shop.Or they can use a slide hammer to remove ,but damages the bearing. Best to buy bearing and have cash for an alignment job too.Then replace front rotors. Rotor and hub install is ez after you get bearing pressed.Rear rotor and bearing are bolt on though.

Apr 06, 2009 | Hyundai Motor 1997 Tiburon

2 Answers

Change front wheel bearings


u will need to remove the brake cailper and the the brake rotor, then the hub retaining nut, that is a large metric nut, the bearing and hub must come off, then u will need to take this hub to a machine shop or the dealer and have the new bearing pressed in.
BCA/NATIONAL Part # 510078 moreinfo.gif {Ball Bearing Bore=1.5354" Outer Diameter=2.9134" Width=1.4173"}
Front Wheel PRICE: $47.99, PART SOURCE: Rockauto.com

3bcf37f.jpg

Mar 12, 2009 | 2003 Hyundai Tiburon

1 Answer

What's involved in changing the front wheel bearings on a 2003 Hyundai Tiburon? Thank you


A whole bunch its toouch basically your overhauling that side taking off the wheel taking rotor off pulling out the hub dearing and pressing it back inlooking at approx 2-2.5 hors and then you made alignment but if you want to know exacxtly how to do this go to collisionrepairadvice.com its worth it

Mar 12, 2009 | 2003 Hyundai Tiburon

1 Answer

2003 Hyundai Tiburon Gt rear brakes


hi not conversant with the tiberon in uk but will try to help ? if you remove the rear wheel then look at the brake disc (rotor) most hyundai rear discs on uk models are secured to the rear hub by 2x screws posidrive or tork heads ? if this is so on yours then no problem you will have to remove the caliper first from the carrier 2xbolts h/brake off then undo 2xbolts securing caliper carrier tosuspension stub assy your disc /s are most probably vented discs? or may be standard discs? remove the screws then you may have to hit disc from behind with hammer to jolt free as they are sometimes rusted on due to high temps and rain ideal conditions to create rust as you prob know? re assemble is reverse hope this helps ?

Oct 20, 2008 | 2003 Hyundai Tiburon

Not finding what you are looking for?
2003 Hyundai Tiburon Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...