Cars & Trucks Logo

Related Topics:

Terrie Ellis Posted on Sep 30, 2017

I put new timengbelt n water pump n my 98dodgeneon and I turned the came by hand n it loaped over cause plugs was still in I put back together and now I got a miss while idleing but has not lost power and runs great out on road if u keep car above 2000 rpm runs great but miss at idle did I work or bend a valve

  • Terrie Ellis Sep 30, 2017

    We're is idle in sensor n what's it look like

  • Michael Barker Sep 30, 2017

    There is no idle in the sensor. The Idle sensor is mounted near to where the throttle cable attaches. Sensor may be faulty or wiring hasn't been plugged back on to it.

×

1 Answer

Michael Barker

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that hasĀ over 10 points.

Problem Solver:

An expert who has answered 5 questions.

  • Contributor 10 Answers
  • Posted on Sep 30, 2017
Michael Barker
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that hasĀ over 10 points.

Problem Solver:

An expert who has answered 5 questions.

Joined: Aug 14, 2013
Answers
10
Questions
0
Helped
4701
Points
43

Sounds like you may have damaged the idle sensor or forgot to reconnect it after putting it back together.

5 Related Answers

66 chrgr

mike loshbough

  • 1011 Answers
  • Posted on May 02, 2009

SOURCE: ENGINE MISSING ABOVE 3800 RPM

no the code is most likely from a dpfe sensor for you egr system not the egr valve itself.a clogged fuel filter though might cause your low revs

Ad

Anonymous

  • 5 Answers
  • Posted on Jun 25, 2009

SOURCE: 2500 to 3000 rpm idle

Change your Thottle positioning Sensor. My 93 lesabre did the same thing and i changed the TPS and it stopped.

Anonymous

  • 6 Answers
  • Posted on Dec 20, 2009

SOURCE: Daewoo Lanos 1.4 1997 Idling really high - Idle Rev Valve?

hi there the problem describe is a common problem you need to take the car into your dawoo/chevrolet dealer as there was a reprogramme that need s to be downloaded to your ecu to fix the problem should only take about 30 mins so should not cost you to much i used to have around 10 to 15 a week to do

Anonymous

  • 248 Answers
  • Posted on Feb 05, 2011

SOURCE: after cleaning the throttle body it looks to be

When you cleaned the throttle body, did you remove the Idle Air Control valve/motor (IAC)? A dirty or defective IAC can be the result of your problems. The IOAC regulates your vehicles idling under various condictions. Try cleaning it first then replace if needed.

Please remeber to rate this solution. Thanks!

cansmo

Reynaldo Andico

  • 2431 Answers
  • Posted on Mar 05, 2012

SOURCE: idel problem on 5.7 1995 silverado

You engine is TBI, It uses a MAP sensor check the vacuum line for crack and make sure yo have a good seal, The distributor also check and make sure the pick up does not have corrosion which causes the relutor to stick. As for the EGR it would cause a misfire, and yes the do fail. I am sticking with the IAC as a problem its a stepper motor and has a high failure rate, chack also the ECT (engine coolant temp sensor) for corrosion that gives false reading.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

My freeze plug came off the back of the block yesterday as it was being flushed. I am a small woman and can fit my hand up in there. How do I get it back on with out it causing what tools do I need ?

I put water pump sealant around the hole and use a socket that just fits in the plug. Use a new plug and hammer the socket until the plug seats fully.
0helpful
1answer

Put water pump on now getting no fire

think you have not put the timing back right and it will need to be re done. hope you used a new belt and adjuster when you put it back together. you need to re line the timing marks on cams and on crank. then put the belt on adjust up making sure the number 1 piston is at the top as well as the timing marks on the cam check this with the crank making, put belt on and adjust up then turn engine one full turn. no spark plugs fitted. back to the timing marks making sure they line up if not re adjust the time until it line back up every time you turn the engine one full turn. then put the spark plugs in etc and start enging.
2helpful
1answer

I have a 1998 volkwagon beetle 2.0 that needs a water pump so i buy the water pump install it put everything back together and put water inside then it just spilled out. tried to start it and now the

you should did your home work before removed old water pump most vw engines water pump is part of the timing belt assembly so when time to replace around 80k miles you should order complete timing belt kit which includes water pump with it.
so after you finish up if you didnt try to hard to run engine you may or may not damage any piece from your valve train!!even with all proper parts you have on your hand you still need high cost speciality tools to complete timing belt replacement on that engine recommendetion is tow your vehicle to mechanic shop and let them do it for you it will save you time and money!
good luck!
5helpful
1answer

WATER PUMP REPLACE DIAGRAM

  1. Step 1 Drain the antifreeze from cooling system. Remove belt from water pump. Examine and see if you have to remove anything else to get out the water pump. If so make a diagram of everything you are removing so you can put it back together.
  2. Step 2 Remove the hoses from the water pump. Find all bolts holding the water pump in . Loosen each one a little bit. After all are lose you can then remove them. Remove water pump. Put new gasket on and install new water pump. Hook up hoses to water pump. Look at your diagram and replace everything you had to remove earlier. Put the belt back on.
  3. Step 3 Shut the drain on system and refill cooling system. Make sure you use the antifreeze that is designed for system. Run engine for a couple of minutes. Check for leaks and check coolant level. Add if necessary. If there is no leaks you are ready to go.
0helpful
1answer

Cost of fixing daewoo leguenza

what is the labor rate where u live, here it is $135.00 US per hour, the water pump is driven off the camshaft timing belt, a new timing blet idler pulley is also a must, so you will need a new timing belt also, it can't be used over
Water pump cost $80.00
Timing belt $20.00
Idler pulley for timing belt $35.00
Coolant $20.00
Labor 4 hours
so here in my area this would be $600.00 job
0helpful
1answer

3.0L tranny wont properly mount to motor

Did you make sure the torq converter was all the way into the trans. pump? sounds to me it was not, and i hope for your sake you did not break the ears on the pump. Unbolt the trans. unbolt the torqconverter from the flexplate and spin the converter untill it drops back in the pump keep spinning until it drops in a good inch and then you got it.
0helpful
1answer

New water pump wont start

It could be the crankshaft position sensor located near the crankshaft under you sparkling new water pump. Wires may be disconnected.:) Good Luck
Not finding what you are looking for?

59 views

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...