Which company can fix my stramm high pressure cleaner - hose

you might try here....

http://www.supercheapauto.com.au/Product/Blackridge-Pressure-Washer-2-6HP-1900-PSI/340534
they carry the washer must have parts.

is it the pump or the hose there is a high pressure hose that usually starts to leak before the pump goes . spray some cleaner on the pressure hose and get it clean then crank it on and have someone turn the steering wheel a couple of times to see if you can spot the leak.

I would guess the steering fluid has gummed up your solenoid, making it difficult for your starter to engage the solenoid.

Yes to your question. I would start by checking the hoses coming from the power steering pump. You should have a high & low pressure hose. In most cases the high pressure hose has developed a leak. You can spray the hoses and pump down with brake parts cleaner to getting any oil or grease off of these parts. Then you can drive the car for a day or 2 depending on how fast the leak is and after that check the hoses and related parts you have cleaned and locate any fresh fluid and that should help you locate the leak. Not sure of the year of your vehicle but more than likely you have a rack and pinion unit on it and you can spray that down as well because that could be leaking as well. I personally use brake parts cleaner because it is a GREAT cleaner and it drys itself and doesn't leave a residue. Hope this helps.....

Disconnect battery ground cable.
Remove engine Air Cleaner (ACL) .
Disconnect electrical connector in back of engine cooling fan motor.
Remove radiator fan shroud.
Disconnect constant control relay module harness from headlamp harness and place constant control relay module on top of engine to provide accessibility to power steering lines.
Remove wiring harness guide retaining screws and position guide aside.
Remove screw at power steering hose bracket.
Remove anti-rattle clip.
Remove plastic strap retaining tubes to power rack and pinion steering gear.
Remove power steering pressure hose at power steering pump.
Remove power steering pressure hose at power rack and pinion steering gear.
Remove power steering pressure hose from vehicle.
Reverse procedure to install new hose.
Fill and bleed power steering system.

This called idle surging, here is what you do to fix it in most cases.

I want you to get a can of intake cleaner (ABOUT $5.00) from any local auto parts store like NAPA or Carquest, do not use carburetor spray, intake cleaner only or u will damage the Teflon coating inside the throttle valve and air bypass valve, it is made by a company called CRC, remove the air intake hose to the engine, hold the idle high so the engine won't stall, then spray the can of cleaner into the intake while keeping the engine running, use at least 1/2 the can, shut down the engine and disconnect the battery for 5 minutes, then restart and complete a number of mixed driving cycles, town, freeway, stop and go etc., after a few days the problem will go away as the system will relearn to the clean intake.

do the following, it fixes these kinds of problems, follow the instructions exactly.
Get a can of intake cleaner from any local parts store, not carb spray, intake cleaner, it is made by a company called CRC, remove the air intake hose to the engine, hold the idle high so the engine won't stall, then spray the can of cleaner into the intake while keeping the engine running, use at least 1/2 the can, shut down the engine and disconnect the battery for 5 minutes, then restart and complete a number of mixed driving cycles, town, freeway, stop and go etc., after a few days the problem will go away as the system will relearn to the clean intake.

You have a sludged up idle speed control valve, do the followning procedure it should fix the problem.
, Get a can of intake cleaner from any local parts store, not carb spray, intake cleaner, it is made by a company called CRC, remove the air intake hose to the engine, hold the idle high so the engine won't stall, then spray the can of cleaner into the intake while keeping the engine running, use at least 1/2 the can, shut down the engine and disconnect the battery for 5 minutes, then restart and complete a number of mixed driving cycles, town, freeway, stop and go etc., after a few days the problem will go away as the system will relearn to the clean intake.

YOU CANT USE A REGULAR FUEL LINE ON POWER STEERING AS A HIGH PRESSURE HOSE.BECAUSE POWER STEERING PRESSURE IS 1000 PSI.YOU HAVE TO BUY THE POWER STEERING HIGH PRESSURE HOSE IT HAS NUMBER OF PLIES MATERIAL WEAVES TO MAKE IT STRONG.IT WAS MADE FOR POWER STEERING HIGH PRESSURE.YOU DONT HAVE A BLOCKAGE .THE HIGH PRESSURE HOSE JUST WORE OUT.REPLACE IT .IT SHOULD FIX THE PROBLEM.

you can but what are the price of the parts .just a pain to get at the fittings just make sure they are the right hoses and they are put back on the high pressure and low pressure sides .cut the old ones and tap a socket over the fitting rather then wrench might strip it and have troubles geting out and root them the same spot the old ones came from