Question about 2010 Cadillac SRX
Either a broken wire under seat or seat module is bad. Also check your fuses.some have a fuse box under back seat
Posted on Jan 13, 2019
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
wow i feel sorry for you because Cadillac designed this bulb to be a don't get to bulb but OK here's what you do take the bottom cover off or skid plastic panel under neath the front end theirs little plastic clips holding it on just get come dikes and don't cut them but just use it to help pull them out. after you get that off use a flash light and locate your light housing you should see two screws holding the house in i think those screws are 8mm i cant remember remove those two screws and be careful the metal from the bumper cuts you pull the light housing out and remove all the screws around the housing and open the housing up replace the bulb and make sure your contact to the bulbs clean and then reassemble the way you took apart. if you cant get it well then best bet is take it somewhere i know Cadillac charges an arm and a leg so you can go somewhere else.
Posted on Jan 25, 2009
First you have to take out the one and only screw in the rear hatch door - it's where the hand pull down is you use to close the hatch.
Then you have to pop all the plastic clips all the way around the plastic door panel, trying not to pull them out from the frame . If you do pull out the white plastic plugs from the frame you better make certain you take them off the plastic housing and insert them back into their frame holes - or you will never get the housing back on.
Once you have the housing loose disconnect the inside tail gate light wire to remove the whole thing. Then you have to remove 7 to 8 nuts from the back of entire License plate, back up bulb housing using a deep socket to get in there. Work it loose from the rear of the car and it will come out just enough to work on the lights.
This is tricky since the screw mounts don't give you much room to work with.
Once you have the license plate and back up bulb frame loose you will see the two housings for the license plate bulbs on top.
Slide out the license plate bulb lens and twist the bulb connection to remove the bulbs.
Replace both of them - you don't want to do this again in a month when the other one blows.
Once you take out the bulbs you might see that the housing is melted where the bulb wanted to burn through. Drill two small holes one is each end of the housing before I put everything back together to release some of the heat.
Reverse the whole process to put everything back together. It's not easy.
Make sure you insert the cables through the opening for the hatch handle or it will kink and not work properly.
The bulbs come in a two pack of cost $4.95 .
Posted on Nov 24, 2009
No fuse.These seats are protected with relays and a seat module.The module is under the drivers seat.There are 3 connectors and it would be hard to check all these wires for power to the motors.First look under the seat and make sure none of the connectors came apart under the seat by something that might have been left or rolled under it.The 2 main ones you can check are the connector 2 terminal C and connector 3 terminal A.C is a black wire which is ground and A is a red wire which is the feed power wire.Connector 2 is green and 3 is black.If the ground and power wires are good then you could have a bad drivers seat module.What I would do is go to the salvage yard and find a used module to try.Good luck.
Posted on Dec 07, 2009
Testimonial: "Thanks for your assistance. Great information"
Tips for a great answer:
Mar 28, 2018 | Cars & Trucks
Mar 15, 2018 | 2007 Cadillac SRX
Sep 10, 2017 | Cadillac Cars & Trucks
Sep 10, 2017 | Cars & Trucks
Aug 10, 2017 | Cadillac Cars & Trucks
Jan 08, 2017 | 2010 Cadillac SRX
Dec 10, 2016 | 2006 Cadillac SRX
Jan 17, 2013 | 2010 Cadillac SRX
Jan 17, 2013 | 2010 Cadillac SRX
Dec 12, 2010 | 2007 Cadillac SRX
459 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: