I need a pulley diagram for a 2004 XG350 L sedan

View related parts

Hyundai XG350 Bolt

Part Number: 11403-08253
Other Name: Outlet Pipe Bolt, Outlet Tube Bolt Manufacturer Note: NEW A/TReplaces: 11403-08251 $0.54 MSRP: $0.71 You Save: $0.17 (24%) Add to Cart
Fits the following Vehicles:

• 2002-2005 Hyundai XG350 ' High Grade ' 4 Door Sedan

https://www.hyundaipartsdeal.com/oem-hyundai-xg350-belt_tensioner_bolt.html

have you tried looking on youtube for a diagram?

Its located on the left side of the engine, (passenger side). Take the timing chain cover off, look for a wire just in front of two pullies, closest to you. One maybe two bolts, its probably caked with metal debri, being that it's a magnet which reads gaps in a thin disk. This gap tells the engine when to fire whatever cylinder. My sensor went bad after 3 days from purchasing the vehicle from a dealership, they wouldn't help me since there was no warranty. Pos. The engine shook so hard I thought it was going to break a motor mount, after a day it was underivable. Contact me for a diagram if needed. Hyundai xg350L 2004 3.5L repair shop manual. [email protected]

2004 Hyundai XG350 Car Stereo Radio Wiring Diagram
Car Radio Constant 12v+ Wire: Red
Car Radio Switched 12v+ Wire: White/Green
Car Radio Ground Wire: Black
Car Radio Illumination Wire: Brown/White
Car Stereo Dimmer Wire: Green
Left Front Speaker Positive Wire (+): Brown/White
Left Front Speaker Negative Wire (-): Black/White
Right Front Speaker Positive Wire (+): Brown/Yellow
Right Front Speaker Negative Wire (-): Black/Yellow
Left Rear Speaker Positive Wire (+): Brown/Red
Left Rear Speaker Negative Wire (-): Black/Red
Right Rear Speaker Positive Wire (+): Brown/White
Right Rear Speaker Negative Wire (-): Black/White

Search Results

02 XG350 air, sunroof, seat warmers, and intermittent wipers quit ...

www.hyundai-forums.com/.../149142-02-xg350-air-sunroof-seat-warme...

Sep 27, 2012 - 9 posts - ‎5 authors
An automotive shop pulled up the car and said their was a fuse box with a lot of relays in it on the passenger compartment .... 2004 XG350L .... Same thing happened to me, 2002 XG350, sunroof, blower, vanity light all out.

Hyundai XG350 wipers not working Questions & Answers ...

www.fixya.com > ... > wipers not working > Cars & Trucks > Hyundai
Hyundai XG350 cars & trucks wipers not working questions and answers. Ask your Hyundai wipers not working related question. ... 2004 Hyundai XG350.

Hyundai wipers not working Questions & Answers - Fixya

over p/s pulley,down to a/c pulley ,up to crankshaft pulley ,under tensioner pulley

This is when you need a tech to dial into the problem! 8 yrs is when you need to make a decision!

1. The fan belt routing diagram for 2004 Volkswagen Bora 1.4 16V



2. The fan belt routing diagram for 2004 Volkswagen Bora 1.6 16V



3. The fan belt routing diagram for 2004 Volkswagen Bora 1.8 Turbo




4. The fan belt routing diagram for 2004 Volkswagen Bora 2.0



5. The fan belt routing diagram for 2004 Volkswagen Bora 1.9 TDI


CS = Crankshaft
Gen = Alternator
G = Guide pulley
T = Tensioner pulley
AC = Air Conditioning
PAS = Power Assisted Steering

First, check the oil pressure switch's wire to ensure that it's not contacting the belt pulley.

The SMP model runs less than $20 if you buy online

http://www.partsgeek.com/catalog/2004/hyundai/xg350/body_electrical/oil_pressure_sender.html

It's about the size of your thumb, and is threaded into the lower edge of the block next to the oil filter.

***Don't forget to VOTE for the guys who take an interest in helping!

3.5L Engine

Remove or disconnect the following:

1. Negative battery cable
   

• Engine coolant
  
• Water pump pulley bolts
  
• Alternator bolt, loosen only
  
• Water pump pulley and drive belts
  
• Crankshaft pulley
  
• Timing belt cover(s)
  

1. Turn the crankshaft until the timing marks on the camshaft sprocket and cylinder head are aligned.
   
2. Loosen the timing belt tensioner bolt and turn the tensioner counterclockwise as far as it will go. Tighten the adjusting bolt.
   
3. Mark the timing belt with an arrow showing direction of rotation.
   
4. Remove the timing belt.
   
5. If defective, remove the timing belt tensioner.
   

Timing belt sprocket alignment mark positioning for belt removal and installation—3.5L engine

To install:

1. If necessary, install the timing belt tensioner.
   
2. Attach the top of the tensioner spring on the engine coolant pump pin. Ensure the hook on the pin is facing down and the hook on the tensioner is facing away from the engine
   
3. Rotate the timing belt tensioner to the extreme counterclockwise position. Temporarily lock the tensioner in place.
   
4. Align the timing marks of the camshaft and crankshaft sprockets.
   
5. Install the timing belt on the crankshaft sprocket, then onto the rear camshaft sprocket.
   
6. Route the belt to the coolant pump pulley, the front camshaft sprocket and the timing belt tensioner.
   
7. Apply force counterclockwise to the rear camshaft sprocket with tension on the tight side of the belt and check that timing marks are aligned.
   
8. Loosen the tensioner bolt 1–2 turns and tighten the timing belt to a tension of 57–84 lbs. (260–380 N).
   
9. Turn the crankshaft two turns clockwise.
   
10. Readjust the sprocket timing marks and tighten the tensioner bolts.
    
11. Install the timing belt covers.
    
12. Install the crankshaft pulley and tighten to 108–116 ft. lbs. (150–160 Nm).
    
13. Install or connect the following:
    
    • Timing belt cover(s)
      
    • Crankshaft pulley
      
    • A/C compressor belt
      
    • Water pump pulley
      
    • V belt
      
    • Negative battery cable
      
    • Engine with coolant