Cars & Trucks Logo

Related Topics:

David Heffernan
David Heffernan Posted on Aug 21, 2017
Be the first to answer

I have a 2004 avensis 1.6 petrol and it is stuck in 4th gear no bearing noise or grinding shift lever wont go left or right only up or down but can not select any gears

Answer This Question

5 Related Answers

Anonymous

  • 17 Answers
  • Posted on May 24, 2009

SOURCE: won't go into gear to drive. may be transmission?

If the clutch has never been changed most likely it is that. The way you can check it is by removing the transmission and looking at the clutch disc. It could be transmission syncros but I am willing to bet you just need a new clutch.

Ad

Anonymous

  • 166 Answers
  • Posted on May 26, 2009

SOURCE: Transfer gear case shift jammed

There are four probable causes when the gear is stuck in one position, and they are precisely explained in this handy diagnostic article that I know will help narrow down the culprit of your difficulty:
http://yourhandymanzone.com/Your_Handyman_Zone_How_To_Pages_Vehicle_Car_Zone_Cars_Trucks_Vans_Transmission_System_Stuck_In_One_Gear.htm

Good luck!
Brad

Anonymous

  • 124 Answers
  • Posted on Jul 15, 2009

SOURCE: 1997 pontiac sunfire manual transmission won't shift out of gear.

What you can try is to remove the shift cables from the transmission side. then move the shifter and see if everything is free if it's still sticks then the cables are going to be replaced. if everything is moving with the cable off. then you need to remove the shift tower on the tranny (where the shift cable is I belive it's 5 bolts) remove the tower and you will see the shift pin. Inside the tower there is a cotter pin that breaks and that will cause you to have one gear and unable to selected another gear. If you are not mech inclined I would no attemped the shift tower repaire, the cables do it will save you money. The shift tower has bushings that can fall into the tranny.

Anonymous

  • 2841 Answers
  • Posted on Aug 08, 2009

SOURCE: 92 Accord Automatic shifting

Has anyone change the transmission fluid and used anything other than Honda ATF-Z1. If so, have the fluid/filter changed in this car and use only Honda Fluid. This is the only fluid that you can use in a Honda. Even if you have used the correct fluid an fluid/filter change may help. If that is not the case then I suggest you seek out a trusted professional.

Anonymous

  • 119 Answers
  • Posted on Aug 19, 2009

SOURCE: VW GOLF 1.4 1999 S. Gearbox makes whining sound at idle

No good news on this one I think
Your whining sound problem is the Layshaft bearings in the gearbox are badly worn. It also seems that the baulk rings are damaged on 5th gear.
John

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I need a diagram of the locations of the shifting solenoids on a 2006 VW Jetta please
double posted same car same problem but this time a new Key clue.
what do you mean out of 4th gear.
learn the tell a drivers evidence hear,
PRNDL123,can';t move the LEVER here
or the auto trans (none told or engine or country told)
the A/t fails to up shift 3 to 4, in Drive,?
or trans is stuck in 4th drive. no matter what I do, even in Reverse I get 4th gear forward?

1: check all fuses first./
2: scan the PCM and report all DTC errors and skip none set.


shifting out of 4th gear

what does that mean, I am clueless. 4>3 down shifts fail?
Read full answer
Sep 09, 2022 • Cars & Trucks
1helpful
2answers

I have a 2006 Hyundai Tiburon 4 cylinder 5 speed transmission it will not shift into 3rd gear it makes a grinding noise and you go to shift into fourth gear and acts like there is no 4th gear what do I do
sounds like the shifter plate has moved or the alignment on the gear lever mechanism is out of line or even the gear stick plate linc is out of line. how much wobble is in the gear stick when you put into gear. if you can put in gear and move it far left or right then its not working right.
Read full answer
Jan 04, 2018 • Hyundai Cars & Trucks
1helpful
1answer

Mazda 2300 grindes when shifting into 4th
4th gear is not a gear as such but a coulping of the input and out put shafts to make a complete shaft
If there is a problem moving this coupling it indicates a syncro ring problem or spigot bearing failure in the end of the input shaft
either way it amounts to a gear box removal and pull down for repairs.
Read full answer
Jul 07, 2015 • Mazda Cars & Trucks
1helpful
1answer

N16 manual makes a whiring noise when slowing down from 60kph in 4th, stops when put into nuetral
sounds like a bearing is on the way out in the gearbox, nothing really to worry about yet, if it is still going into gear, and not making a grinding noise.

mine makes a whirring noise when accelerating through 1-3rd gears.

It's when there is grinding and growling in the gear box that you need to worry.
Read full answer
Nov 11, 2014 • Cars & Trucks
0helpful
1answer

Clutch pedal is stuck half way down wont shift gears
Check clutch cable, check clutch lever, if there is some noise from the clutch when the engine is running, then the release bearing is most likely faulty, or even the clutch pressure plate.
Read full answer
Apr 16, 2014 • 1997 Subaru Impreza
0helpful
1answer

Grinding clutch
I'm a little confused on your description of the noise. If I understand you correctly It is making the noise when it shifts smoothly into gear but at the same time it makes a grinding noise ? It possibly can be synchronizers if the grooves on the inside of the synchronizers are worn bad enough to where the gear isn't slowing down enough causing a grind as the clutching teeth on the gear mesh with the synchrode and the shift collar.
If it is making noise in all gears except 4th you may have countershaft brgs failing. The power flow in 4th gear goes directly through the mainshaft and has a 1 to 1 ratio. All other gears the powerflow goes through the countershaft causing a load on the countershaft so if you have bearings failing in the countershaft you will hear noise in all gears but 4th.
i hope I understood you correctly .
Read full answer
Jan 18, 2014 • 2002 Subaru Forester
2helpful
2answers

Cannot get 5th and reverse gear. Feels like neutral. 1, 2, 3 and 4 work fine.
the linkage is loose or poping out! check to c if trans is tightend down
Read full answer
Aug 22, 2012 • 1995 Dodge Neon
1helpful
1answer

1999 honda prelude manual transmission isn't disengaging all the way when i shift, sometimes locking the shifter in gear or not allowing me to up or down shift. I know my master and slave cylinders need to...
This depends as dose it do it when cold or hot.
2nd when you push in pedal and put in gear dose it go in clean or hard to select 3rd can you hear a grinding noise when pushing in pedal and noise goes
when you take you foot off the clutch pedal IF so then its the thrust bearing on clutch REPLACE ALL .4th if you push in clutch pedal and select a gear and let the clutch out if drive right out (replace)
Read full answer
Sep 27, 2009 • 1999 Honda Prelude
0helpful
1answer

Grinding gears while shifting gears
4th gear started grinding when I shifted up or down and then 3rd started to do the same unless I shifted very carefully. You have 2 choices. 1 - rebuild it since you'll have to take apart to find the problem. 2. try changing the gear oil and make sure its the right synthetic grade, very expensive. This solution is working so far for me. BTW you must change the gear oil in the manual trans every 40k
Read full answer
Aug 10, 2009 • 2002 Kia Sportage
8helpful
2answers

Grinding noise while driving.
Possible causes:

a) a brake disc shield is too close to the disc, and it's coming into contact in the circumstances you outline

b) pebbles stuck between the disc shield and the disk

c) dried out wheel bearings

d) worn Universal Joints in the drive shafts

e) worn A/C pump

f) worn alternator

g) worn water pump

Is the noise still present above 15 miles an hour and past 1500 rpm when the clutch is disengaged (i.e. gearbox in neutral?). The answer to this question may help you to pinpoint the source. I know it's stating the obvious but the fact that you're hearing a grinding sound means it's caused by something that is moving relative to something else. Again this should help narrow down the cause.
Read full answer
Jun 01, 2009 • 2000 Chevrolet Blazer
Not finding what you are looking for?

View Most Popular

Cars & Trucks

Related Question

I need a diagram of the locations of the shifting solenoids on a 2006 VW Jetta please

  • Cars & Trucks

72 views

Ask a Question

Usually answered in minutes!

Popular Questions

Avensis bulb replacement

2005 Toyota Avensis 2.0

How to replace toyota avensis door mirror

2005 Toyota Avensis 2.0

How do i change the navigation screen language from japanese to english in Toyota Avensis 2006

2006 Toyota Avensis 2.0

Location of fuse box in toyota avensis 2005

2005 Toyota Avensis 2.0

How to adjust front headlight

Toyota Avensis Cars & Trucks

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Toyota Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...