Question about 1998 Chevrolet Malibu
Look where you belt is.timing is run by crank shaft and cam shaft.
Posted on Apr 12, 2017
On the front of the engine, no matter what engine all have the cover in the front, that would be the passenger side of the engine on front wheel drive models
Posted on Apr 12, 2017
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
The first step is to remove all the parts that are in the way of you being able to remove the valve covers. (Ex.: air intake, loose wires etc.) Then you will need to remove your valve covers (using basic tools) and be very careful to not let anything get on your lifters, which your valve covers protect. Once you have the valve covers off compare the new gaskets to make sure they are the right size. Then remove the old gasket and replace with the new one using a high temp gasket sealant (available at any auto parts store) to attach the gasket to the valve covers. Then tighten down snug and check for leaks after replaced.
Posted on May 06, 2009
SOURCE: 98 chevy malibu:engine wont turn
Check with a battery tester if you have power at the starter, Are the Battery post clean, Are any fuses blown in the fuse Box, check for any corrision.
Posted on Aug 13, 2009
Your playing with fire to try to adjust something thats not designed to be adjusted even the hi dollar fancy racing teams are very careful going any from the factory specs as they have dynos and scopes and way more money to spend than me and you. No stock engine being used as a daily driver should be changed unless it's back to standard. Your stepping into deep **** unless you have deep pockets to deal withblown mototers and other bad stories. I know them and I can write them
Posted on Nov 03, 2009
The turn and hazard flashers are integrated into one flasher on these models. The flasher is located in the hazard warning switch and the hazard warning switch is located on the trim plate. Replace the flasher by unplugging the old one, removing it from the panel, and plugging in the new one.
Remove the bezel from the ignition switch
Carefully remove the instrument panel accessory trim plate.
To remove the trim plate, use a suitable prytool to carefully apply pressure at the retaining clip points . . .
. . . then gently pull the accessory trim plate away
Detach the electrical connector from the hazard warning switch.
Unplug the electrical connector from the hazard warning switch . . .
Unfasten the screw securing the hazard warning switch and remove the switch.
. . . then unfasten the screw securing the hazard warning switch and remove the switch from the vehicle
Installation is the reverse of removal.
Posted on Dec 01, 2009
Testimonial: "just what I needed, thank you so much."
you need a haynes manual for your specific car.. this manual will give info from a complete teardown of vehicle. you can get one at any auto parts store. this manual will show the settings for timing.
Posted on Jul 15, 2010
Tips for a great answer:
Mar 21, 2014 | 2009 Chevrolet Malibu
Oct 19, 2017 | 1998 Chevrolet Malibu
Jan 05, 2011 | 1998 Chevrolet Malibu
Nov 06, 2010 | 1998 Chevrolet Malibu
Sep 02, 2010 | 1998 Chevrolet Malibu
Aug 21, 2010 | 1998 Chevrolet Malibu
Mar 13, 2010 | 2004 Chevrolet Malibu Maxx
Dec 01, 2009 | 1998 Chevrolet Malibu
Jul 02, 2009 | 1998 Chevrolet Malibu
21 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: