My 2001 Town and Country's rear windshield wiper motor is kaput. How do I change it without destroying the rear tailgate paneling

3 bolts hold the wiper motor to its mount. One of those bolts goes through a ground strap. Without that ground having a good connection the wipers will continue to run looking for their parking position through that ground. If you have to run a separate ground wire from the wiper motor to a good visible ground on the fender well or firewall.
I hope this helps

wipers won't work??? - CarGurus

www.cargurus.com > Questions > Chrysler > Town & Country

CarGurusFeb 15, 2012 - 1998 Chrysler Town & Country LXi My windshield wipers won't work. The turn ... I have a Plymouth Horizon & the same problem, but I'm fairly sure it's theswitch on mine. ... Ended up taking it to the dealership - it was a wiring problem from the body control module to the switch. ... Used Dodge Caravan".

Auto Repair : How to Test a Windshield Wiper Motor ...

? 3:04
https://www.youtube.com/watch?v=7EliY2Hwj0E
May 12, 2009 - Uploaded by ehowauto
In order to test a windshield wiper motor, the first thing to do is to make ... He said its the relay and the entire ...

Windshield Wiper Motor Replacement : How to Access a ...

? 3:37
https://www.youtube.com/watch?v=iVBAvvfc1FU
Oct 1, 2008 - Uploaded by expertvillage
Removing windshield wiper arms and intake grading is essential to gaining access to the windshield wiper

Read through these instructions. They go over the front then the rear motor replacement.

http://www.ehow.com/how_12206366_replace-windshield-wiper-motor-2007-honda-crv.html#page=15

There is a nut under the black plastic bezel that needs to be removed. Here is the complete procedure for you to look at. Its possible that your arm isn't adjust at wiper motor...

REMOVAL
- Disconnect and isolate the battery negative cable.
- Remove the rear wiper arm from the rear wiper motor output shaft. (Refer to 8 - ELECTRICAL / REAR WIPERS / WASHERS/REAR WIPER ARM - REMOVAL).
- Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL). Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
- Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL).
- Remove the bezel and gasket from the rear wiper motor output shaft.
- Remove the trim panel from the tailgate inner panel. (Refer to 23 - BODY/SWING GATE/TRIM PANEL - REMOVAL).
- Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
- Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle (REAR WIPER MOTOR REMOVE/INSTALL).
- Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
- Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
- Remove the rear wiper motor and mounting bracket from the tailgate as a unit.



1 - BEZEL AND GASKET
2 - OUTPUT SHAFT
3 - TAILGATE OUTER PANEL
4 - NUT
5 - NUT COVER

What you will need to do is to remove the small plastic cap on the wiper arm by prying it off with a screw driver. Then remove the nut that holds the arm onto the shaft. Then get yourself a battery cable puller (from auto parts store) and pull the arm off of the shaft..



1 - SPARE TIRE
2 - WRENCH
3 - FLIP-UP GLASS
4 - PARK RAMP
5 - REAR WIPER ARM
6 - PIVOT COVER

MARK THE POSITIONS OF THE WIPER ARM ON THE LIFT GATE GLASS,THEN REMOVE WIPER ARM COVER AND NUT AT THE OUT SIDE LIFT GATE, THEN THE BEZEL.BECAREFUL DONT DAMAGE PAINT.ON THE LIFT GATE.AND REMOVE THE UPPER AND LOWER LIFT GATE TRIM PANELS.DISCONNECT THE ELECTRICAL CONNECTOR AT THE REAR WIPER MOTOR, THEN REMOVE THE TWO MOUNTING BOLTS SUPPORT WIPER MOTOR WHILE REMOVING BOLTS.THEN INSTALL NEW WIPER MOTOR AND PUT EVERY THING BACK IN PLACE VISA VERSA.

REMOVAL

1. Disconnect and isolate the battery negative cable.
2. Remove the rear wiper arm from the rear wiper motor output shaft.
3. Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel .Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
4. Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel
5. Remove the bezel and gasket from the rear wiper motor output shaft.
6. Remove the trim panel from the tailgate inner panel.
7. Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
8. Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle
9. Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
10. Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
11. Remove the rear wiper motor and mounting bracket from the tailgate as a unit.

To Install just reverse steps

check the wires from multi function switch to relay

Fuse # 5 in your panel should be a 20amp fuse, which provides power to wipers. Not 100% sure, but would bet there is a relay in that circuit before motor. Try to feel/hear, exactly where clicking is coming from. It is usually easy to simply narrow the click noise area down, then set finger lightly on relays, and feel it when it clicks. Pull it out & have tested or replace.

Check in your user's manual for your fuse location on the rear windshield wiper. These grand cherokee's have electronic actuators in every door. Inside these actuators they have very little motors and move everything via plastic. Very bad design flaw, as most of these actuators are 300-400 dollars to replace. You can find ones in salvage yards for 50 though. On your rear hatch, the door and the window are run by this actuator.