Question about 2007 Nissan Xterra Off Road

Open Question

The head bolt torque for 2007 nissan xterra 4.0l

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 221 Answers

SOURCE: i put a new head gasket on my nissan oulsar..the engine is a ga15 what are the head bolts torque down to

Goto Service Center and you'll have the Latest Information.

Posted on Jul 14, 2008

Ad
  • 383 Answers

SOURCE: replacement of a head gasket on 2.5 liter nissan altima 2002

frajogag: First off, be aware that these bolts are "torque to yield" bolts (streach bolts). What this means is that instead of torqueing the head bolts to a specific torque specification, they are torqued down to a set spec and then tightened by rotating the bolts a certain angle, like 90 degrees. and all of them are turned the same amount.
This means that the shanks of the bolts must be checked to make sure they are not too thin (or the bolt has already stretched beyond limits and is prone to snap if used)
Here is how you check the bolts. Measure the bolt using a micrometer, at the base, or within the first 13mm from the end where it threads in. Then go to about 10mm before the threads end heading toward the top of the bolt. There should not be more than a 0.23mm (.0091 inch) or less difference or the bolt should be discarded.
Torque the bolts down to 98.1Nm ( 72.ft lb)
Looking at the head from the side, so you are looking at the full length from side to side, I will number the head bolts in this fashion.
#1 & 2 are directly in front of you and in the center of the cylinder head crossing it width wise.
#3&4 are to the left of #1&2, / #5&6 are to the right of #1&2
#7&8 are to the left of #3&4 / #9$10 are to the right of #5&6
Now, you have the sequence.
After the initial pull, back off all the bolts in the same sequence and then retorque them to 36 Nm ( 28 ft lb)
Using a torque angle wrench or having the ability to accurately judge turning angles. Rotate (clockwise) to a 75 degree angle. do this to all the bolts using the sequence I had provided.
Rotate the bolts (clockwise) 75 degrees again on all bolts in the same sequence. The proceedure is complete!

Posted on Apr 23, 2009

  • 8 Answers

SOURCE: need cylinder head bolts torque settings for nissan 3.2d

what nissan model do you need the head torques for

Posted on May 01, 2009

ebjebs
  • 197 Answers

SOURCE: head bolt settings

1st - step; - 22 ft./lbs. 2nd - step; - 58 ft./lbs. 3rd - step, loosen all bolts completely; 4th - step; - 22 ft./lbs. 5th - step; - 54 ft./lbs.fig074.png

Posted on Feb 28, 2010

  • 36 Answers

SOURCE: I need head bolt torque sequence for 2002 nissan

So 80 degrees is approx. how many ft lbs.

Posted on Jun 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specs for the heads on a 2000 Nissan Xterra 3.3 l


AutoZone has a lot of info on torque specs for various vehicles.
The Xterra uses torque to yield bolts which must be replaced every time the bolt is removed.
Here's the site -
https://www.autozone.com/repairguides/Nissan-Frontier-Xterra-1998-05/Engine-Mechanical-Components/Cylinder-Head/_/P-0996b43f8037f9d4

Jan 09, 2018 | Nissan Cars & Trucks

Tip

Nissan altima 2.4 L torque specs.


Torque sequence ---------------- | 9 3 1 6 8 | | 7 5 2 4 10 | ---------------- Step 1: Torque in sequence 22 Ft/Lbs Step 2: Torque in sequence 58 Ft/Lbs Step 3: Loosen all bolts completely Step 4: Retorque all bolts in sequence 22 Ft/Lbs Step 5: Retorque all bolts in sequence 54-61 Ft/Lbs recheck final torque in sequence *** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque. 0900c15280265395.jpg

on Jul 08, 2010 | Nissan Altima Cars & Trucks

2 Answers

I NEED TORQUE SPECS FOR ROD AND MAIN BEARINGS BOLTS.. AND HEAD BOLTS TORQUE


That 5th step is also 100 degree turn. This for 08 2.0L, note the engine code or what ever that is? If that mr2ode is correct, I'll see what I can find for crank and rod bolts.
head bolts-pi1e5hhs2rrjjzjs3yfdldu3-3-0.jpg

Nov 21, 2017 | Nissan Sentra Cars & Trucks

1 Answer

How to replace a knock sensor on a 2002 nissan xterra


Unplug the electrical plug/connector from the base of sensor. You will have to take out bolt from the head of the sensor that threads into the cylinder head. Thats really it. Unplug - Unscrew - replace!

Dec 31, 2010 | 2002 Nissan Xterra

1 Answer

I have a v-6 2000 nissan xterra. What are the


Rod bearing torque

Step 1 - 10-12 ft.lbs
Step 2 - 60-65 Degrees more


Main bearing caps torque

66-74 ft. lbs

d6bcc92.gif

Jul 02, 2010 | 2000 Nissan Xterra

1 Answer

I need head torque specs on a 2000 xterra


Cylinder Head Bolt step1 22Ft Lbs- Step 2 59ft Lbs- Step3 Loosen All Bolts- Step 4 22Ft lbs- Step5 86-91 degress.Thanks

Mar 06, 2010 | Nissan Xterra Cars & Trucks

4 Answers

Torque settings for cylinder head nissan sentra


Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Jul 18, 2009 | 1999 Nissan Sentra

2 Answers

How to remove tail lamp for nissan xterra 2007 ?


Open the back hatch and there are two screws. Take them out and you will have the lamp off.

Oct 02, 2008 | 2004 Nissan XTerra

2 Answers

Torque and sequence to Intake Manifold for 3.3L Nissan Xterra 2000


Hi El Faraon,
I believe that you're dealing with 12 mm bolts and nuts....THESE ARE NOT THE SPECS FOR YOUR ENGINE, but I believe that if you use them you'll be close....Tighten in three stages up to 22nm....choose the bolts from the centre of the manifold and circle outwards until you reach the last one.....It may be a good idea to draw an overhead or plan view of the unit, marking out the bolt positions.....Start at the centre and mark the sequence and follow that....What is important is starting at the centre, so that nothing becomes warped....

Hope this helps,

Regards, Johngee10

Sep 06, 2008 | 2000 Nissan Xterra

Not finding what you are looking for?
2007 Nissan Xterra Off Road Logo

Related Topics:

892 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...