Replacing timming belt on 1999 kia sephia alin the timming marks show please

SOURCE: how to set the timing in the kia sephia 2000 model

You need a timing light and a new belt

Greg Bernett

• 2993 Answers
• Posted on Jul 26, 2009

SOURCE: 1999 kia sportage timing marks

Crankshaft match marks


Align marks on timing belt pulley and pump body.

Camshaft pulley alignment marks

1. Align marks on camshaft pulleys with alignment marks on seal plate.
2. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
   
3. Loosen tensioner lock bolt.
4. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
5. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
6. Apply a force of 22 lbs to timing belt between camshaft sprockets.
7. Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)
8. NOTE: Replace tensioner spring if timing belt deflection is excessive.

1. Install lower timing belt cover.
2. Install upper timing belt cover.
3. Install power steering drive belt and adjust belt tension.
4. Install fan pulley.
5. Install generator drive belt and adjust belt tension.
6. Install A/C drive belt and adjust belt tension.
7. Install splash guard.
8. Install fan and fan shroud.
9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
10. Install fan shroud mounting bolts.
11. Install fresh air duct.
12. Connect hose to resonance chamber.
13. Connect battery negative cable.

Greg Bernett

• 2993 Answers
• Posted on Aug 29, 2009

SOURCE: 2002 kia spectra timming belt digram needed to

1. Disconnect battery negative cable.
2. Remove power steering and air conditioning compressor drive belt by loosening power steering fasteners.
3. Remove generator bolts and generator belt.
4. Remove water pump pulley.
5. Remove crankshaft pulley and timing belt guide plate.
6. Remove upper/lower timing belt covers.
7. Turn crankshaft clockwise until "I" mark on intake camshaft pulley and "E" mark on exhaust camshaft pulley align with marks on cylinder head cover.

SOURCE: i need a new timming belt on a 01 kia sephia how

Hi there,

Below are the procedures to remove the timing belt...

1. Disconnect negative battery cable.


2. Loosen power steering lock bolts and nuts accordingly and remove tension from power steering (P/S) and/or air conditioning (A/C) compressor drive belt. 3. Remove P/S and/or A/C drive belt.



4. Loosen generator mounting bolts and adjusting bolt. 5. Remove generator bolts.




6. Remove water pump pulley.




7. Remove crankshaft pulley and timing belt guide plate.






8. Remove upper and lower timing belt covers.





9. Turn crankshaft so that timing mark on timing belt pulley is aligned with timing mark on engine.







10. Check that "I" mark on intake camshaft pulley is aligned with mark on cylinder head cover and "E" mark on exhaust camshaft pulley is aligned with mark on cylinder head cover.


Do not move camshaft or crankshaft once timing marks have been correctly positioned.







11. Loosen tensioner pulley lock bolt.
12. Protect timing belt with a rag.
13. Remove tensioner pulley.




14. Remove timing belt.



Regards,
Jeep Brainy

SOURCE: Timing belt replacement for 2001 Kia Sephia

For California models recommended at 105,000 miles.Belt needs to be inspected at 60,000 and 90,000, miles and replace at 105,000 miles.
Except California replace at 60,000 miles. Note 1.8L engine is a interference engine, if timing belt goes bad will cause major internal engine damage.