No details came with GM CD unit. Not obvious how the unit installs - - No mating connector or attachment points found. Circular knobs on both sides of CD unit ( ~ 3/8 " dia x 1/4 " depth)suggest insertion into mounting rails. We have the interface cable.
SOURCE: 2000 Camry LE bad odor from a/c heater cabin vents
Possible the smell is coming from the bacteria living on your ac evapourator. You can buy a spray for this that you set off inside the vehicle. Follow the instructions on the tin.
SOURCE: Installing a cd changer into a 2002 Jaguar S-Type
SOUNDS LIKE YOU HAVE A VERY EARLY MODEL CD CHANGER ALPINE UNIT THE S TYPE
USED A AUDIOVOX CD CHANGER HOPE THIS IS USEFUL
SOURCE: looking for color code (diagram) - 7 wire trailer harness/wiring
If you haven't purchased the plugs yet. The wire color codes should be included in the package.
SOURCE: CD Mechanical Error on 2003 Cadillac CTS
take the radio apart and take them out one by one, i just fixed my yesterday
SOURCE: headlight mounting for 98 Buick Century
f
GM Century/Lumina/Grand Prix/Intrigue 1997-2000 Repair Guide
Headlamps REMOVAL & INSTALLATION
Sealed Beam
NOTE
Do not apply pressure to the plastic bubble of the vertical aim indicator.
To install:
Composite Headlamps
The headlamps used on the
majority of vehicles covered by this guide are called "composite
lamps". Unlike the glass sealed beam units used on older vehicles,
these headlamps are made of special plastic using small halogen gas
bulbs. The bulbs are replaceable, but they do require special handling.
CAUTION
Halogen bulbs contain a gas under pressure. Handling a bulb
improperly could cause it to shatter into flying glass fragments.
Always allow the bulb to cool before removal. Always use the following
precautions to help avoid personal injury.
Turn the light switch OFF and allow the bulb to cool before
changing bulbs. Leave the switch OFF until the bulb replacement
procedure is complete.
Always wear eye protection when changing a halogen bulb.
Handle the bulb only by its base. Avoid touching the glass. Do not drop or scratch the bulb.
Keep the bulb away from moisture.
Place the used bulb in the new bulb's carton and dispose of it properly. Keep halogen bulbs out of reach of children.
Depending on the installation, the low-bean and the
high-beam halogen bulbs may actually be removable without removing the
entire composite headlamp assembly. Look your application over
carefully to see there is enough room behind the headlamp to fit your
hand to remove the bulb holder. Since removing the composite headlamp
assembly is not difficult, the following procedure assumes that the
headlamp is being removed from the vehicle for halogen bulb service.
WARNING
Do not touch the glass bulb with your fingers. Oil from
your fingers can severely shorted the life of the bulb. If necessary,
wipe off any dirt or oil from the bulb with rubbing alcohol before
completing installation.
Headlamp adjustment may be temporarily made using a wall,
as described below, or on the rear of another vehicle. When adjusted,
the lights should not glare in oncoming car or truck windshields, nor
should they illuminate the passenger compartment of vehicles driving in
front of you. These adjustments are rough and should always be
fine-tuned by a repair shop which is equipped with headlamp aiming
tools. Improper adjustments may be both dangerous and illegal.
Fig. Typical composite headlamp aiming rods
Fig. Typical horizontal and vertical adjuster locations
Fig. Vehicle headlamp aiming device (RH)-Buick shown, others similar
Before removing the headlamp bulb or disturbing the headlamp
in any way, note the current settings in order to ease headlamp
adjustment upon reassembly. If the high or low beam setting of the old
lamp still works, this can be done using the wall of a garage or a
building:
Hope helps with this (remember rated this) Good luck.
Testimonial: "Great input with diagrams! Excellent, just what I was looking for. Jim DeAngelis"
78 views
Usually answered in minutes!
×