2000 Nissan Frontier Logo

Related Topics:

Anonymous Posted on Apr 01, 2017

How can I replace a map sensor on my 2000 nissan frontier

I am having trouble getting the map sensor out of the old plug.

5 Related Answers

Anonymous

  • 740 Answers
  • Posted on Dec 31, 2008

SOURCE: map sensor

THIS VEHICLE DOES NOT HAVE A MAP SENSOR..Good Luck Thanks for using FIX YA Happy New Years

Ad

Anonymous

  • 1392 Answers
  • Posted on Jun 10, 2009

SOURCE: replace seat belt on 2000 nissan frontier

Should be a T50 or T55. Should have a cover over the bolt. Remove the cover, and remove the bolt.

JIMMY

  • 1374 Answers
  • Posted on Jun 10, 2010

SOURCE: 1999 Frontier: nissan frontier 2000 automatique tansmision revers...

Either transmission oil pump is on its way out or reverse circuit is clogged , reverse shift solenoid is defective TCM may be defective , transmission range sensor begining to fail or manual shift valve and pressure regulator are defective.

Suggest taking the vehicle to a transmission repair shop they will diagnosis it and repair it.

Jonah Oneal

  • 14092 Answers
  • Posted on Jun 14, 2010

SOURCE: approx. how many hours should it take at a shop to

2.4 ENGINE TIME IS 3 HOURS 40 MINUTES THE 3.3 ENGINE 2 HOURS 20 MINUTES.

Testimonial: "thanks so much! I didn't want to get screwed ;-)"

Randy Ohler

  • 14585 Answers
  • Posted on Jun 14, 2010

SOURCE: 2000 nissan frontier knock sensor code & distributor

no but the knock sensor does send a signal the ecm and it will ****** or advance the distributor timing

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I have a 2000 nissan frontier v6 that is spitting and sputtering when driving.

no VIN posted or country and means ,impossible to know this.:
he Nissan Frontier is a nameplate used on two different pickup truck models by Nissan: VG30 V6???
VG33 V6???
the Nissan here has a cam timing belt, if allowed to slip at 60 to 100kmiles the engine is wrecked, valves in the cyl. head bend!

so do you ignore this belt>? if yes it will get worse. $$$$$$$$$$$$
do not disconnect the map, and leave it like this, ever.
forget evap code until engine is fully serviced.
all Nissan's are interference engine,<< belt never IGNORE
1: check the cam belts for fray,cracked or skipped time.
2: new spark plugs (before o2, fuel cannot burn with bad spark.)
3: check fuel pressure to spec, FPR can be bad. and low pressure.
4: pulling map can kinda hid a bad FPR, if pressure is low.
5: new distributor timed wrong. as most noobs do,
6: clogged 1/2way injectors.
0helpful
1answer

2000 nissan frontier rough idle and has a po325,po300,po120,and po304

THROTTLE POSITION SENSOR, MISFIRE, #4 MISFIRE, KNOCK SENSOR, THESE ARE YOUR TROUBLE CODES, PO120,PO300, PO304, PO325, RESPECTIVELY, REPLACE THE TPS @ THROTTLE BODY, REPLACE KNOCK SENSOR , @ ENGINE BLOCK, REPLACE YOUR SPARK PLUGS & PLUG WIRES ! AND YOU MUST ALSO REPLACE BOTH YOUR AIR & FUEL FILTERS, DISTRIBUTOR CAP & ROTOR , INSPECT, MAY NEED TO REPLACE, I WOULD ANYWAY !!!!!!!! ADD SOME GOOD FUEL INJECTOR CLEANER TO TANK, NEXT FUEL UP !
0helpful
1answer

I have a 2000 Nissan frontier with a v6 I have crank. Position sensor code I changed the sensor but I still have the code

There is a crank and a camshaft position sensor. If you have verified both are working or replaced, pull negative battery cable for 2 hours or overnight. This should reset error codes.
0helpful
1answer

2000. Nissan frontier. V6. P335 trouble code won't go away crank position sensor

If you have replaced the crank sensor and the code comes back, it may be a problem with the wiring harness or connector, or the plate the sensor reads.
0helpful
1answer
0helpful
2answers

Replacing knock sensor do I need to replace the harrness

No you don't have to change the harness unless it is cracked, broken, or have burn marks.
0helpful
2answers

How do you replace camshaft sensor on 2000 nissan frontier tru tu

How did you know that your cam shatf sensor is in trouble? do you have your own Code Reader. It is so complecated, you can replace the sensor as easy as it could be but are you sure that your sensor is dead? Tell me pls. what had happend to your engine. was the engine check always lighting before when you are driving but you've just ignored the warning light.
0helpful
1answer

2000 nissan frontier knock sensor code & distributor

no but the knock sensor does send a signal the ecm and it will ****** or advance the distributor timing
0helpful
1answer

Map sensor

THIS VEHICLE DOES NOT HAVE A MAP SENSOR..Good Luck Thanks for using FIX YA Happy New Years
Not finding what you are looking for?

322 views

Ask a Question

Usually answered in minutes!

Top Nissan Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...