Cylinder head and conrode bolt torque jetta IV 1.6 AKL engine 2004 model

Question edited for clarity.
Question moved to model category.

All here for the three engine types

https://www.autozone.com/diy/repair-guides/nissan-frontier-xterra-1998-05-torque-specifications-repair-guide-p-0996b43f8037fa5c

https://www.google.com/search?q=2004+Nissan+Xterra.+cylinder+head+bolt+sequence+and+torque+specs

..

1. Tighten the cylinder head bolts in the sequence shown. Using the 4 step torque turn method, tighten according to the following values:

• • Step 1: All to 34 Nm (25 ft. lbs.)
  • Step 2: All to 68 Nm (50 ft. lbs.)
  • Step 3: All to 68 Nm (50 ft. lbs.)

CAUTION: Do not use a torque wrench for the following step.
Step 4: Turn an additional 1/4 turn

• Step 5: Install and tighten bolts (1-10) in sequence shown, to 41 Nm (30 ft. lbs.) .

1. Tighten bolts (1-10) again to 41 Nm (30 ft. lbs.) PLUS 1/4 turn in sequence shown.
2. Install main bearing bedplate to engine block bolts (11-20), and torque each bolt to 28 Nm (20 ft. lbs.) in sequence shown.

Connecting Rod Cap Bolts 54 Nm (40 ft. lbs.) + 1/4 turn
1997 Jetta: Torque settings..vw..the head, fly wheel, big ends.


1997 Jetta3 1800 feul injection


Vibration Damper/belt Pulley
Tighten 20 Nm (14.8 ft lb) Crankshaft Toothed Belt Sprocket Tighten 90 Nm (66 ft lb) + 90° Camshaft Sprocket Tighten 80 Nm (60 ft lb) Main Bearing Cap
Tighten 65 Nm (48 ft lb) FLYWHEEL TORQUE
Torque 60 Nm. (44 ft. lbs.) + 1/4 turn (90°) [1] [1] Always replace bolts.
CYLINDER HEAD TIGHTENING TORQUE [1] :
1st sequence: 40 Nm (30 ft lb)
2nd sequence: 60 Nm (43 ft lb)
Final sequence: plus 1/2 turn (180°)
Here are some additional specifications, thanks
ntake Manifold
Mounting Bolts 25 Nm (18 ft. lbs.) Bearing Cap Nut 20 Nm (15 ft. lbs.) Rod Bearing Cap
Assembly
Tighten 30 Nm (22 ft lb) + 90° To measure radial clearance
Tighten 30 Nm (22 ft lb) but NOT additional 90° TIGHTENING SPECIFICATIONS
Oil Pump Bolt 20 Nm (14 ft. lbs.) Oil Tube To Block 10 Nm (7 ft. lbs.) Exhaust Manifold to Cyl. Head 25 Nm (18 ft lb) Exhaust Manifold to Front Exhaust Pipe 40 Nm (30 ft lb) Water Pump
TIGHTENING SPECIFICATIONS
Cover Bolts 10 Nm (7 ft. lbs.) Mounting Bolt and Studs 20 Nm (15 ft. lbs.) + 1/4 turn (90°) Pulley Bolts 25 Nm (18 ft. lbs.)

TIGHTENING SPECIFICATIONS
Connecting Rod Nuts:
Tighten In Two Stages:
First Stage 30 Nm (22 ft. lbs.) Second Stage turn an additional 90°(1/4 turn)

In the link

https://www.google.com/search?q=Jetta+iv+1.6+AKL+engine%2C+main+and+big+end+torque+settings

..

cyl head no new bolts needed stage 1. 50nm stage 2. 70nm stage 3. 103 nm conrod/bigends new bolts not needed stage1. 25nm stage2 50nm hope that helps

Cylinder head bolt torque sequence
The Rod Bearing Cap Torque
The Main Bearing Cap Torque 38 Foot pounds (Final torque)


Step 1: Torque 10-12 Ft/LbsStep 2: Torque 17-21 Ft/Lbs


Note :
Torque sequence ------------------------
' 11 '
front ' 13 9 3 1 6 8 '
of ' '
engine ' 14 7 5 2 4 10 '
' 12 15 '
------------------------
Step 1: Torque all bolts in sequence 22 Ft/Lbs
Step 2: Torque all bolts in sequence 47 Ft/Lbs
Step 3: Loosen all bolts in reverse sequence
Step 4: Retorque all bolts in sequence 22 Ft/Lbs
Step 5: Retorque all bolts in sequence 43-51 Ft/Lbs
Step 6: Retorque bolts 11 thru 15 in sequence an
additional 4-6 Ft/Lbs
** CAUTION ** This engine uses 2 different length head
bolts. "#1" Is the long bolt, while remaining bolts
are short. **Do not confuse location of these bolts**
recheck final torque in sequence

get the service and repair manual from the given and get the solution easily http://toolsnyou.com/

cylinder head bolt torque

52-55 ft lbs. cold engine
59-63 ft lbs. hot engine

connecting rod cap nut 26-28 ft lbs. SOHC
connecting rod cap nut 23-26 ft lbs. DOHC

main caps 41-44 ft lbs.

hi to tighten you have to do it in 4 stages as follows
1st stage 40nm leave 5 mins 2nd stage 60nm leave 5 mins 3rd stage 90 degrees leave 10 mins 4th stage 90 degrees then you are done i will try put order on here i hope this works as follows
10 4 2 6 8 front of engine back of engine 7 5 1 3 9

in that order hope this helps