How do i remove pillar trim removal on 06 taurus so I can get to driver seat belt and untwist it. Twist is pretty severe, like 3 times twisted

from autozone.com:

Removal & Installation

1. Disconnect and isolate the negative battery cable.
2. Remove the right quarter trim panel as follows:
   1. Remove first rear seat. Remove the second rear seat, if equipped.
   2. Remove the sliding door sill plate.
   3. Remove the quarter trim bolster.
   4. Remove the upper C-pillar trim and D-pillar trim panel.
   5. Remove the first and second rear seat belt anchors.
   6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
   7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
   8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.

   
   

Fig. Removing the trim panel to access the rear blower motor

i. Disconnect the wiring harness connector from the accessory power outlet, if equipped.

j. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.

k. Pull first rear seat belt through the access hole.

l. Remove the quarter trim panel from the vehicle.

3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).

4. Twist the blower motor out of scroll housing.

5. Disconnect the blower motor wiring connector.

6. Remove the blower motor from vehicle.


Fig. The rear blower motor is held in place by four screws
To install:

1. Install the blower motor unit into the vehicle.
2. Reconnect the blower motor wiring connector.
3. Secure the blower motor into scroll housing.
4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
5. Install the right quarter trim panel as follows:
   1. Install the quarter trim panel in position in the vehicle.
   2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
   3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
   4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
   5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
   6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
   7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
   8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
   9. Install the D-pillar trim panel and upper C-pillar trim.
   10. Install the quarter trim bolster.
   11. Install the sliding door sill plate.
   12. Install the second rear seat, if equipped, and install the first rear seat.
       
6. Reconnect the negative battery cable. Check blower motor operation.

Removal & Installation

1. Disconnect and isolate the negative battery cable.
2. Remove the right quarter trim panel as follows:
   1. Remove first rear seat. Remove the second rear seat, if equipped.
   2. Remove the sliding door sill plate.
   3. Remove the quarter trim bolster.
   4. Remove the upper C-pillar trim and D-pillar trim panel.
   5. Remove the first and second rear seat belt anchors.
   6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
   7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
   8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.
      
      
      

      Fig. Removing the trim panel to access the rear blower motor
      

   9. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
   10. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
   11. Pull first rear seat belt through the access hole.
   12. Remove the quarter trim panel from the vehicle.
       
3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
4. Twist the blower motor out of scroll housing.
5. Disconnect the blower motor wiring connector.
6. Remove the blower motor from vehicle.
   
   
   

   Fig. The rear blower motor is held in place by four screws
   

To install:

1. Install the blower motor unit into the vehicle.
2. Reconnect the blower motor wiring connector.
3. Secure the blower motor into scroll housing.
4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
5. Install the right quarter trim panel as follows:
   1. Install the quarter trim panel in position in the vehicle.
   2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
   3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
   4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
   5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
   6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
   7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
   8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
   9. Install the D-pillar trim panel and upper C-pillar trim.
   10. Install the quarter trim bolster.
   11. Install the sliding door sill plate.
   12. Install the second rear seat, if equipped, and install the first rear seat.
       
6. Reconnect the negative battery cable. Check blower motor operation.

Hope helps (remember to rate this).

Most of the time this happens because the belt gets twisted behind the B pillar trim panel. The lower portion of the panel that the belt goes behind can be removed enough to see behind it by gently pulling outward, it is held in place with plastic clips. If the belt is twisted up in there, untwist it and snap the panel back in place.

this is a simple repair many dont know. remove or pull off plastic pillar post cover, seatbelt probably twisted inside. twist it back around so it runs flat and lube slightly with a light lube spray on metal gearing. i had the same problem w mine pk

may have gotten twisted inside the cover on the roller by the door where the belt comes out remove the plastic trim the roller also has a ratchet lock check to make sure functioning properly if belt twisted un twist and pull uot slack and push twist thru opening and un twist till belt is set up correctly if roller rusted stuck or damaged replace

Most likely remove the b-pillar trim cover to access it. Usually 2 or 3 bolts that hold thh retractor in.

please don't forget to rate, thx.

Retractor and Tongue—Sedan
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Safety Belt Bolt Bit T77L-2100A
NOTE: Safety Belt Bolt Bit T77L-2100-A should be used for safety belt removal and installation.

Removal

1. Remove rear seat cushion. Refer to Section 01-10 .
   

Seat Cushion, Rear Sedan
Removal

1. Apply knee pressure to lower front portion of the rear seat cushion. Push rearward to disengage rear seat cushion pad and frame (600A88) from rear seat cushion front retainers (63370).
   

1. Remove rear seat cushion from vehicle.
   

1. Remove rear seat back. Refer to Section 01-10 .
   

Seat Back, Rear 60/40 Split Bench—Sedan
Removal

1. NOTE: Safety belt bolts do not secure seat back to vehicle.
   
   Remove rear seat cushion as described.
   

1. Fold down back seat and remove two bolts in the center of each seat back striker plates.
   

1. Remove two bolts from outboard rear seat back frame retaining brackets.
   

1. Lift seat back up and pull forward to remove from vehicle.
   

1. Remove panel (52018) and quarter trim panel (31012). Refer to Section 01-05 .
   

Trim Panel, Quarter—Sedan Removal

1. Remove rear seat. Refer to Section 01-10 .
   

1. Pull up on rear section of rear door scuff plate that overlaps lower quarter trim panel.
   

1. Pull lower quarter trim panel away from body.
   

1. Remove safety belt retaining bolt.
   

1. Feed safety belt through lower quarter trim panel.
   

1. Remove safety belt anchor plate-to-sill bolt from quarter panel.
   

1. Remove retractor anchor nut and retractor from rear quarter panel.
   

1. Remove upper seat belt anchor bolt and anchor from upper rear quarter panel.
   

1. Slide anchor plate end of safety belt through the openings in the quarter trim panel.
   

1. Remove outboard front safety belt retractor and tongue (611B08) from the vehicle.
   
   
   
   
   
   Item Part Number Description 1 386277-S190 Bolt (Part of 611B68) 2 31012 Upper Rear Quarter Trim Panel 3 611B60 Retractor and Tongue 4 N800937-S190 Nut 5 389370-S190 Bolt 6 — Rear Quarter Panel (Part of Body) 7 52018 Lower Rear Quarter Trim Panel 8 — Mounting Stud (Part of Body)

1. Remove seat belt anchor bolt and retractor and tongue from rear deck panel.
   
   
   
   
   

Installation

1. To install, reverse Removal procedure.
   

1. Make sure the safety belt webbing is not twisted. If it is, remove the twist.
   

1. Tighten retractor anchor bolt and safety belt anchor plate-to-sill bolt to 34-46 Nm (25-33 lb-ft).
   

1. Check the restraint system for proper operation.
   

never seen one here in spain,but most cars you have to remove the door rubber surround first then the kicker plate to remove the pillar trim to get to the seat belt mechanism .best of british

You'd need to pickup the need parts at the junkyard. You'll need the "A" to "B" pillar trim, lower "B" pillar trim, front seat belts and seatbelt giude from a 1995 SC1 or SC2.

The treaded hole in the frame of the car where the track of the automatic seatbelt assembly attaches is in a slightly different place than the three point system. Its not a problem though. You just need to drill a 3/4" hole slightly above the existing hole in the trim panel. The existing hole is hidden by the seatbelt and not noticable at all.

Everything else pretty much bolts or snaps into place.

I've done this swap on several 1991-1994 Saturn S-Series.

bet the belt is twisted pull back the rubber door seal and remove the top buckle should be possible to remove the trim pull the belt all the way out and untwist   go for it