Can't get the lift & slide mech. to work in my 2011 wrangler JK pass side seat. How can I repair it?

Not covered by a fuse.

Fuse Box Diagram Jeep Wrangler (JK; 2007-2018)

https://fuse-box.info > jeep > jeep-wrangler-jk-2007-20...

Here you will find fuse box diagrams of Jeep Wrangler 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017 and 2018, get information about the .

..

get it serviced, its a new car

same , as in location
or same as in , same gear ratio?
and there are many submodels of jk, like rubicon?
what is your concern?

your best option is to try unbolting the seat from the car to access the latch then pry it open with a screw driver
after its removed you will need to go though the proces to remove the seat cover and repair the release mech.

The middle row seat slides forward to the middle position (and several other positions as well.)

Owners manual explains how to slide rear seat foreard.
Remove middle row seats. Lift handle under 3rd row seat cushion on passenger side. Raise seat cushion up until it locks up. Then lift the lever on the passenger side of seat and pull seat forward until it locks in place.

if you don't have owner manual, go to motorcraft.com, pro center, tech info, owner manual.
join our group for free help.

please rate too. Thanks.

http://groups.yahoo.com/group/villagerquest/

you need to replace glass or is it leaking if leaking then you have to remove upper seat belt covers pop off remove bolt 14mm and the trims on upper pillars pry off carefully held in by clips remove covers on interior light at front where sunroof switches are there are screws by bulbs disconnect connector remove center light cover and screws disconnect connector with clean hands remove rbber trim around sunroof opening and plastic cover on each side of sunroof glass held on with plastic screw clips then remove four 10mm nuts lift sunroof glass out of car remove cover and screws from rearview mirror all plastic trims around headliner move pass seat forward most and flip back rest all way down roll pass window fully down then slide headliner out of car now you can remove electrical connectors and remove water flow hoses from sunroof unit remove 8 12mm nuts holding frame to roof remove through door you will see the track sunroof slides on remove nuts along problem is silicone between track and frame is deteriorated lift track clean replace silicone reattach frame to roof dont put trims or liner in till test connect switches and glass to frame make sure sunroof works and closes fully then go through car wash to see if leak is fixed

Did you install stronger drive shafts?

the middle seats come out easily. There are 2 handles you have to lift up on each of the bucket seats, they are in the front of the seat down by the seat tracks. After you lift them, tilt the seat upward in the front and rotate them backward. Then lift out of the hooks. Each seat is held down by 4 hoks.

The 3rd row seat is not designed to come out xcept by a technician. It does slide forward all the way up to the front seat. It has a sliding seat track.
First, lift the T handle under the seat cushion on the left front side of the seat. This will allow you to lift the seat bottom up all the way to lcok in the full up position.
Then, lift the lever on the same side of the seat and slide the seat forward. It will stop in 4 places.
Rear -Rear
6 inches forward of that.
another two ft to the second row seating position
full frward against the front seats.

Pleae rate as fixya if this helps.

Seat —Third Row Bench Removal
CAUTION: Removal of the third row bench seat requires more than one technician.

1. Remove the second row seats. For additional information, refer to Seat—Second Row .

1. Remove the floor mats.

1. Lock the seat cushion in the upright position.
   1. Lift the handle to release the cushion.
   1. Lock the seat cushion in the upright position.

1. Move the third row bench seat to the second row position.
   • Lift the seat track release handle.

1. Remove the two bolt covers.

1. Remove the two seat track front bolts.

1. Remove the four seat track rear bolts.
   1. Position the rear seat cushion floor cover aside.
   1. Remove the four seat track rear bolts.

1. Remove the third row bench seat.

Clock spring mech is prob bad, first easy check is remove airbag 2 8mm bolt from back side of wheel make sure wires are still connected if they are good the clock spring mech is bad you can use a steering wheel puller to remove wheel and clock spring mech just snaps out and has 2 plugs on it, I have 2 if you need one.