Cars & Trucks Logo

Related Topics:

Bobbie Correll Posted on Mar 12, 2017

2008 Chevy Uplander intake manifold tuning valve stuck open how can I fix this

1 Answer

Jay wiedemann

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

  • Contributor 1 Answer
  • Posted on May 18, 2018
Jay wiedemann
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Joined: May 18, 2018
Answers
1
Questions
1
Helped
2502
Points
1

Can someone send me a video or diagram where the2002 chevy trailblazer LS fuel lines fo

3 Related Answers

tace899

tace899

  • 291 Answers
  • Posted on Jul 26, 2014

SOURCE: My 2008 Chevy uplander intake manifold is open

Be more specific. What do you mean by "open"? Does the manifold gasket leak, is the manifold cracked, is the air filter or air filter hose not connected? What are the symptoms, and who told you it was open?

Ad

carl blood sr

  • 846 Answers
  • Posted on Jul 26, 2014

SOURCE: My 2008 Chevy uplander engine light on and the

The intake code means its leaking from the intake,bad gaskets, or a vacuum leak. check for bad gaskets on intake manifold. You can tell by putting a bit of oil around the maifold. if it is leaking the engine will flair up. To check this, External leak-- Coolant seeps through the broken intake manifold gasket to the outside of the engine. If its bad enough you will see coolant dripping from gasket. Coolant seeps through the damaged gasket to the inside of the engine, mixing with motor oil. If you suspect an internal leak, check your oil dipstick. Or if you have a substance under oil filler cap that looks like a milkshake, Oil is mixing with coolant. this means intake gaskets are bad, Now for the camshaft sensor, If you have a manifold leak. this could be giving you a false camshaft reading! Because, If sensor is bad vehicle will not start unless theres a wire problem. Symtoms of a bad sensor are--- engine sputtering, poor acceleration, stalling/inability to start. HopeI helped you out! Good-Day!

Gary Nitowski

  • 326 Answers
  • Posted on Sep 21, 2014

SOURCE: i have a 08 uplander i just put a throttle body

sounds like you have to do a cable adjustment.
if you have two people one of the easiest ways to do this is have someone inside the drivers sine press the gas pedal all the way to the floor.
Loosen up all the hold down cable connectors near the throttle body.
Re position cable tauntness so the valve body is open full and not a pinch more.
Tighten everything in place then release gas pedal.
you should have enough play in the cable for the sensors to register zero.
now clear the code should be no more problem, works on just about any car that has fuel injection.
appriciate a rating, Gary

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

2008 Chevy Uplander base van. How to fix (unstick valve) on it, error code P2070 open valve.

Question edited for clarity.
Question moved to model category.

It is the intake manifold tuning valve that is stuck and fortunately not the Inlet valve itself.

https://www.google.com/search?q=2008+Chevy+Uplander+P2070

//
0helpful
1answer

2011 chevy cruze code po2076

P2076 is Trouble code for the intake manifold tuning valve. You need to check power supply and signal to connectors. Check also the wirings. You can also monitor from the scan tool regarding the value of the position sensor of intake manifold tuning valve and the value commanded by the ecm. Sometimes this valve get stuck and will not respond to ecm controls. ?
0helpful
1answer

11 chevy cruze engine code p2070

intake manifold tuning, valve stuck open.
0helpful
2answers

2008 dodge avenger code p2004

Intake Manifold runner control stuck open - bank one:
- Intake Manifold Runner Binding Or Sticking
- Faulty Manifold flow valve
- Manifold flow valve harness is open or shorted
- Manifold flow valve circuit poor electrical connection

There is a factory service bulletin for this problem for 2007-2008 Dodge Avengers. (JS)

If you need further help, reach me via phone at https://www.6ya.com/expert/daniel_4061c3d97c12c4c7

0helpful
1answer

I have a 08 uplander i just put a throttle body on and now i have a code p2070 intake manifold tuning valve stuck open how to i fix it

sounds like you have to do a cable adjustment.
if you have two people one of the easiest ways to do this is have someone inside the drivers sine press the gas pedal all the way to the floor.
Loosen up all the hold down cable connectors near the throttle body.
Re position cable tauntness so the valve body is open full and not a pinch more.
Tighten everything in place then release gas pedal.
you should have enough play in the cable for the sensors to register zero.
now clear the code should be no more problem, works on just about any car that has fuel injection.
appriciate a rating, Gary
0helpful
1answer

My 2008 Chevy uplander engine light on and the code shows for cam shaft sensor and intake manifold what I do

The intake code means its leaking from the intake,bad gaskets, or a vacuum leak. check for bad gaskets on intake manifold. You can tell by putting a bit of oil around the maifold. if it is leaking the engine will flair up. To check this, External leak-- Coolant seeps through the broken intake manifold gasket to the outside of the engine. If its bad enough you will see coolant dripping from gasket. Coolant seeps through the damaged gasket to the inside of the engine, mixing with motor oil. If you suspect an internal leak, check your oil dipstick. Or if you have a substance under oil filler cap that looks like a milkshake, Oil is mixing with coolant. this means intake gaskets are bad, Now for the camshaft sensor, If you have a manifold leak. this could be giving you a false camshaft reading! Because, If sensor is bad vehicle will not start unless theres a wire problem. Symtoms of a bad sensor are--- engine sputtering, poor acceleration, stalling/inability to start. HopeI helped you out! Good-Day!
0helpful
1answer

My 2008 Chevy uplander intake manifold is open what dose it mean

Be more specific. What do you mean by "open"? Does the manifold gasket leak, is the manifold cracked, is the air filter or air filter hose not connected? What are the symptoms, and who told you it was open?
0helpful
1answer

Where is the location of a vent valve solenoid on a 2006 chevy uplander minivan

There are two. One is the Canister Vent Solenoid located above the gas tank and it has to be dropped to change. The other is the Vent Purge Valve and it is located under the hood to the right on the intake manifold close to your brake fluid reservoir.
9helpful
2answers

P2004

intake manifold runner stuck open. 2008 dodge avenger 2.4 how can i fix it....
Not finding what you are looking for?

2,512 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...