2004 Hyundai Tiburon Logo

Related Topics:

R
Roger Edwards Posted on Mar 04, 2017

2004 hyundi tiburon one low beam nothing else

5 Related Answers

Anonymous

  • 4102 Answers
  • Posted on Aug 05, 2009

SOURCE: misfire at low revs

Hi, this could be down to the fuel line and injectors being dirty as at low revs their is less pressure forcing the fuel through.
My first thing to try would be to buy a fuel cleaner that you pour into the fuel tank these tend to solve the problem your having.
Make sure you buy the correct one ie petrol or diesel follow instructions on the bottle for amounts to use then run the car for a good run usually takes about 4 hours of driving time to fully clear all fuel lines and filters.
I use this in my car once a month as you can pick up small traces of dirt from filling stations this then clogs up over time.
Hopefully this will solve your problem if not then give me a shout back and ill assist you further

Ad

Anonymous

  • 1986 Answers
  • Posted on Oct 06, 2009

SOURCE: HOW DO I ADJUST THE LOW BEAM HEADLIGHTS TO SHINE

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Anonymous

  • 205 Answers
  • Posted on Oct 17, 2009

SOURCE: axel removal on 2004 hyundi santa fe

http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?partName=Drive+Train&pageId=0900c152801a5958&partId=0900c152801a5958
Here is a link to autozone.com that has step by step instructions a diagrams for that

Anonymous

  • 265 Answers
  • Posted on Dec 04, 2009

SOURCE: Which is the high beam which is the low beam

The low beam is always on the outside, and the high beam is always closer to the grill...

Anonymous

  • 54 Answers
  • Posted on Sep 18, 2010

SOURCE: low bean headlights don't work

Check fuse box in engine bay (should be near battery) inside should be the fuse for high beam and low beam.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How do i change low beam headlight on 1996 hyundi excell

Take bulb out from inside engine compartment and change bulb. See your user manual.
0helpful
1answer

2001 tiburon

if equipt with a control module may need to get a new one..try your fuseable links off the battery also..
0helpful
1answer

2004 envoy xuv low beams dont work switched fuses 45 and 46 still nothing any ideas

Other possibilities are; the bulbs themselves, burnt or corroded bulb sockets, or a bad headlight selector switch.
1helpful
1answer

Is there more than one relay switch? I found one for the high beams but not one for the low beams. I changed my dimmer switch and the bulbs but nothing has helped, I have high beams just not low beams and...

The low beam relay is #46 in the underhood fuse panel. check its contact pins before replacing it. If they are corroded, try cleaning them first.
1helpful
2answers

Low bean headlights don't work but high beam does on 2004 Hyundai Tiburon. How do you know what the problem is.

Check fuse box in engine bay (should be near battery) inside should be the fuse for high beam and low beam.
0helpful
1answer

Both low beam lights went out... hi beams are ok. is there a seperate fuse for the low beams?

there are seperate fuses however did you check the bulbs. they could just need replacing. there will be fuses for left and right. should be under the hood.
2helpful
2answers

Which is the high beam which is the low beam on a 2003 Hyundai Tiburon?

The low beam is always on the outside, and the high beam is always closer to the grill...
8helpful
1answer

HOW DO I ADJUST THE LOW BEAM HEADLIGHTS TO SHINE

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.
5helpful
1answer

Adjusting headlights on my 2004 ford taurs

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.
0helpful
1answer

Changing the headlights

This picture shows the rear side of the headlamp assembly. I've circled the access caps to the high & low beam bulbs (they just twist off (counter-clockwise) to access the bulbs. Depending on which engine is in your Tiburon, access is easier if you remove three 10mm mounting bolts to the headlamp assemblies and remove the entire headlamp assemblies (see illustration)
c173c7f.jpg You'll want to disconnect these two connectors .. then remember to reconnect them when you put the assemblies back on.

Hope this helps
Not finding what you are looking for?

107 views

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...