How to replace fog lights bulb on a 2006 QX56 Infinti

Video Description
The video above shows how to change the fog light bulb in your 2004 Toyota Camry. Not all models have fog lights - for many Toyotas, it depends on your trim level (XLE) or whether the fog light option was ordered when your Camry was manufactured. Fog lights are typically in the front bumper, below the headlight cluster and are helpful in poor visibility. If one fog light is burnt out on your Camry, we recommend changing both bulbs because the working bulb will be dimmer than the one you replaced and will likely burn out soon anyway.

When you change the foglight on your Camry, be careful not touch the glass part of the bulb with your fingers which causes the bulb to burn out earlier.

Other videos you might find helpful

• 
  Replace reverse light White light when you back up - yup, they burn out and you can replace them with bright LEDs
  2003 Toyota Camry XLE 3.0L V6
  
• How to add transmission fluid If your transmission is running low on fluid, be sure to add some - find out how to do this here!
  2006 Toyota Camry LE 2.4L 4 Cyl.
  
• Complete oil & filter change Sure you can take it in for a $19 lube, but are you OK with a stripped oil pan and cheap parts in return?
  2006 Toyota Camry LE 2.4L 4 Cyl.
  
• Fix leaky hoses The best way to fix leaking hoses is to replace them, but if you don't have time, a stop leak product might work for you
  2006 Toyota Camry LE 2.4L 4 Cyl.
  
• Set the clock to the correct time Is the clock in your car ahead or behind? Learn how to set it here!
  2003 Toyota Camry XLE 3.0L V6
  
• Oil level check Cars burn, leak and otherwise dispense of their oil. Check your level frequently and top up when necessary
  2006 Toyota Camry LE 2.4L 4 Cyl.
  
• See all videos for the 2003 Toyota Camry

Have you checked the bulbs? Fog lights go through bulbs regularly around here.

Perhaps, but your replacement of a headlight bulb would not have "fixed" the other light outages, unless there is a sensor that can tell it was out and therefore, shuts every other light off until it is fixed. A little more likely is the action of moving things to replace the light temporarily "fixed" a bad connection at or near the bulb socket. If it happens again, you will have a clue to the location. It may also be some effect on the headlight relays.

should just be a screw holding the light cover on either at the front or behind bumper then the bulb will just be a bayonet fit

LOOK IN THE OWNERS MANUAL IN THE GLOVE COMPARTMENT,LOOK IN THE BACK INDEX OF MANUAL, LOOK UP BULB REPLACEMENT.IT WILL SHOW YOU HOW TO REPLACE FOG LIGHT BULB.USE LATEX WHEN CHANGING FOG LIGHT BULBS, BECAUSE LIGHT BULBS IS HALOGEN IF TOUCH WITH FINGERS OR HANDS, OILS FROM HANDS WILL CAUSE HALOGEN OVERHEAT AND BLOW OUT.

http://www.elightbulbs.com/2006-Subaru-B9-Tribeca-Replacement-Light-Bulbs under car at fog light unscrew cap pull bulb out do not touch new bulb hold at bottom put back in same way

On the bottom side of the car under the fog light area there will be an inspection cover. it is held in place by two plastic trim clips. they will have what looks like a philips head on the screw. remove both of these then pull out the retainer (they are set up like a dry wall anchor). pull back the cover and unplug the bulb. twist the bulb counter clock wise to remove. install in reverse order.
Good luck!! EJ

Touring Model
Use a wrench to remove the mounting bolt from the underbody through the hole in the splash shield.
Remove the fog light assembly from the bumper by pulling its inner edge first, then the whole assembly out of the bumper.
Remove the electrical connector from the bulb by pushing on the tab and pulling the connector down.
Remove the bulb from the fog light assembly by turning it one quarter turn counterclockwise.
Push the electrical connector onto the new bulb.
Turn on the fog lights to test the new bulb.
Reinstall the fog light assembly into the bumper. Tighten the mounting bolt.
Insert the new bulb into the assembly and turn it one-quarter turn clockwise to lock it in place.
Hope this helps you.

remove headlamp assembly and you can get it from the top pretty easy