Question about Cars & Trucks

1 Answer

Hey there I need the exhaust and Intake(valve) clearance for a komatsu 300-6 please

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Passionate:

    Visited the website for 10 consecutive days.

  • Expert
  • 55 Answers

Note Perform the valve clearance check and adjustment at the engine cold state. 1.Remove all of the ignition coils. 2.Remove the cylinder head cover.
caution Turn the crankshaft always clockwise. 3.Turn the crankshaft clockwise, and align the timing mark on the exhaust camshaft sprocket against the upper face of the cylinder head as shown in Figure. Therefore, No.1 cylinder goes to the compression top dead center. 4.Using a thickness gauge, measure the valve clearance with the arrow shown in Figure. If deviated from the standard value, make note for the valve clearance.
Standard value:

    Intake valve 0.20 ± 0.03 mm (0.008 ± 0.0012 inch)
    Exhaust valve 0.30 ± 0.03 mm (0.012 ± 0.0012 inch)
5.Turn the crankshaft clockwise 360 degrees, and put the timing mark on the exhaust camshaft sprocket in position shown in Figure. Therefore, No. 4 cylinder goes to the compression top dead center. 6.Check the valve clearance with the arrow shown in Figure. In the same procedure as 4.
7.If the valve clearance is deviated from the standard value, remove the camshaft and the valve tappet. For the camshaft removal, refer to Camshaft Removal and Installation . 8.Using a micrometer, measure the thickness of the removed valve tappet. 9.Calculate the thickness of the newly installed valve tappet through the following equation.
A: thickness of newly installed valve tappet
B: thickness of removed valve tappet
C: measured valve clearance
Equation

    Intake valve: A = B + [C - 0.20 mm (0.008 inch)]
    Exhaust valve: A = B + [C - 0.30 mm (0.012 inch)] note The valve tappet ranges 3,000 - 3,690 mm (0.1181 - 0.1453 inch) and has 47 types per 0.015 mm (0.0006 inch). The thickness below a decimal point is stamped on the reverse side of the valve tappet. 10.Install the valve tappet selected through the procedure 9, and put the camshaft in position. For the camshaft installation, refer to Camshaft Removal and Installation .
    11.After installing the timing chain, measure the valve clearance using the procedure 3 to 6. Confirm the clearance is within the standard value.
    caution Completely remove all the old FIPG, which might be remaining among the components. 12.After completely removing the liquid gasket adhering on the timing chain case, cylinder block and cylinder head, degrease them with white gasoline.
    caution The cylinder head cover should be installed within 3 minutes of applying liquid gasket.
13.Apply a 4 mm bead of liquid gasket as illustrated.
Specified sealant:
    THREE BOND 1217G or equivalent
14. Install the cylinder head cover and tighten the tightening bolts using the following procedures.
(1) Temporarily tighten to the following torque in order shown in the illustration.
Tightening torque: 3.0 ± 1.0 N·m (27 ± 8 in-lb)(2) Tighten to the specified torque in order shown in the illustration.
Specified torque: 5.5 ± 0.5 N·m (49 ± 4 in-lb)15.Install the ignition coils.

Posted on Jan 23, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need valve specification on 86 chevy nova


from my 1985/1986 official shop manual:
figure 6A1-39 valve stem and guide clearance
max intake clearance 0.08 mm (0.0031 in)
max exhaust clearance 0.10 mm (0.0039 in)
pg 6A1-17 If clearance is greater than the values given in 6A1-39, then replace the valve and guide

pg 6A1-17
standard overall length
intake 106.88 mm (4.2079 in)
exhaust 106/78 mm (4.2039 in)
do not grind more than 0.5 mm (0.020 in)

Mar 11, 2015 | 1986 Chevrolet Nova

1 Answer

B18b4 valve clearance


Adjust when the engine is completely cold.

B18A
Intake : 0.006" - 0.007" (0.15mm - 0.19mm)
Exhaust: 0.007" - 0.008" (0.17mm - 0.21mm)

B18B
Intake: 0.003" - 0.005" (0.08mm - 0.12mm)
Exhaust: 0.006" - 0.008" (0.16mm - 0.20mm)

B18C
Intake: 0.006" - 0.007" (0.15mm - 0.19mm)
Exhaust: 0.007" - 0.008" (0.17mm - 0.21mm)

Jan 25, 2015 | Cars & Trucks

1 Answer

Please give me the correct tappet clearance of intake and exhaust valve of mitsubishi 4g54 with turbocharger


My initial sweep of the web gives Inlet 0.010 thou, Exhaust 0.008 thou.
You would need to check this because industry norm is to have the greater clearance on the exhaust valve because of the increased heat expansion.

Nov 05, 2013 | 1992 Mitsubishi Pajero

2 Answers

Valve clearance 4g13


make the engine runs for about 30minutes before adjusting the valves,
valve clearances:
intake valve = 0.20mm(0.008 in)
exhaust valve = 0.25mm(0.010 in)
for reference only when the engine is cold,
valve clearances:
intake valve = 0.25mm(0.010 in)
exhaust valve = 0.30mm(0.012 in)
engine specs: mitsubishi 4g13 1.3L (if you have same engine)

Feb 29, 2012 | Mitsubishi Cars & Trucks

2 Answers

I want to set valve clearances on 1997 2.6 petrol holden rodeo. i need valve sequence? how can i tell which is exhast and which is intake?


the valve clearance is intake .006 exhust .010 they must be set with engine cold passenger side is the intake driver side is the exhust send me your e-mail and i will send you the procedure.

Apr 08, 2011 | Isuzu Rodeo Cars & Trucks

3 Answers

Valve clearance 4hj1 isuzu engine


This is the specs for the 4H Diesel engine:
Intake valves clearance cold 0.4mm(.016inches)
Exhaust valve clearance cold 0.4mm(.016inches)

Jan 28, 2011 | 1995 Isuzu Pickup

2 Answers

Procedure of tappet adjustment


make sure engine is warmed up. Put cylinder one at top dead center,remove the valve cover,loosen all adjustment lock nuts,adust intake and exhaust valves on cyl #1 and intake valve on #2 and exhaust valve on #3. now rotate crankshaft 360 degrees clockwise, now adjust intake valves on cyl#3 and cyl #4 and exhaust valves on cyl #2 and cyl #4.now tighten lock nuts and install valve cover. specs are intake valves 25mm clearance and exhaust 28mm clearance, use a feeler gauge,heres a picture to show you where to check clearance.7675a52.gif

Mar 14, 2010 | 1986 Suzuki Samurai

1 Answer

Valve Clearance


valve clearance, with engine hot, intake valves are .005-.006 in, exhaust valves are .011 in, if engine is cold then its intake .009-.011 in and exhaust is .007. hope this helps good luck.

Nov 28, 2009 | 1989 Suzuki Swift

1 Answer

Valve clearance


Hello, For all 615, 616 (4cyl) and 617 (5cyl) through 1985 model year is:
cold intake 0.10mm or .006in
exhaust 0.35mm or .014in
hot intake 0.15mm or .007in
exhaust 0.40mm or .016in
CYA, Gator241

Dec 16, 2008 | 1983 Mercedes-Benz 300-Class

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

22402 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...