Question about 1998 Subaru Legacy

Open Question

How to disable an 1998 Subaru legacys hill holder syste!

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Rebgagnon
  • 382 Answers

SOURCE: will 1999 subaru engine fit in 1997 subaru legacy?

Yes as long as the Motors are the same. You might need to have the computer out of doner car. Doors are suppose to fit 96 to 99.

Posted on Feb 01, 2009

Ad
Rebgagnon
  • 382 Answers

SOURCE: How difficult is it to change the rear struts on a

Removing and replacing is not the problem, easy job. Changing the springs is the only problem. Make sure you are very careful when removing springs. Better to have a parts store do it for you. If you do decide to change yourself just make sure clamps are tight and take your time to follow directions exactly. Be careful, good luck and have a great day.

Posted on Jul 08, 2009

Rebgagnon
  • 382 Answers

SOURCE: is 1998 subaru legacy a 16 pin OBD2 or do i need

Yes it is OBDII. Just a regular scanner is all you need. They run around $30 at most parts stores.

Posted on Jul 12, 2009

centralvalle
  • 386 Answers

SOURCE: Steering wheel clicks on 1998 Subaru Legacy Outback wagon

steering column bearing sounds like a worn out steering column... jack the front wheels off the ground both sides relieve load on steering wheel to see if it lessens the amount of feel and noise, if it does it shoud be the column bearing, replace bearings or complete column,,, also try with the wheels off the ground and safely supported to manualy steer the wheels by hand and see if you feel in roughness or hear any noises,should some minor resistance but be smooth in it movement if everything suspension and steering component wise is in good working condition... please rate my help.. thanks...

Posted on Aug 05, 2009

  • 4 Answers

SOURCE: 1998 Subaru Legacy Outback with Factory issued Car

the easiest way will be to take it 2 a subaru dealer or an auto electriction and get them 2 remove the alarm..but you could dissconnect and un bolt the external alarm siren..

Posted on Sep 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1992 subaru legacy (manual transmission) accelerating problems


Manual transmission subarus have a 'hill holder' feature that is part of the braking system; when you stop on a slight incline, engage the clutch, and step on the brake at the same time, you can take your foot off the brake and the car will not roll backwards. When you go to accelerate and release the clutch the hill holder disengages and allows normal operation.
I suspect that this feature was somehow altered when your brake service was performed. It's activated via a cable that is tied to your clutch cable; the hill holder cable toggles a switch on a mechanism that applies brake fluid to one (or two, depending on model year) brake calipers. I'd start here. If you google hill holder you should find some diagrams of what I'm speaking.
I had a 1995 Legacy with this feature; I disabled when it began malfunctioning. Took 20 minutes as the bolt is in a difficult location but immediately noticed it was much easier to depress the clutch pedal.
Oh yes, my malfunction was so bad (and improperly diagnosed by the local brake 'specialists') that the brakes would lock up while driving and I couldn't move the car! I destroyed my left front brake caliper before figuring out the culprit on my own.

Hope it's an easy fix whatever it is!

Jan 24, 2013 | Subaru Legacy Cars & Trucks

1 Answer

How do i remove a stereo from a 98 subaru legacy


to start you have to pull out your cup holder and unscrew two screws with are holding it in place .then you can pop out the upper an then the lower trim panel .under the lower panel you will see four screws holding the radio .Take em out ad disconnect the antenna lead and electrical connectors.

Feb 13, 2010 | 1998 Subaru Legacy

1 Answer

1998 Subaru Legacy Outback--Rough Idle


I have the same problem!Running on three.I have checked compression,wires,plugs.Changed injecters,plugs.
3 mech.cant figuire it out???

Nov 21, 2009 | 1998 Subaru Legacy

1 Answer

I need the valve adjustment on subaru push rod engine


engine cold.
use firing order 1324

use timing marks put each cyl on tdc

inl = 0.08inch
exh = 0.010

adjust with locknut screw syst

good luck

Nov 09, 2009 | 1992 Subaru Legacy

1 Answer

1998 Subaru Legacy Outback with Factory issued Car alarm malfunction. Alarm will go on by itself, even when it has not been set. I want to permanately disable it!


the easiest way will be to take it 2 a subaru dealer or an auto electriction and get them 2 remove the alarm..but you could dissconnect and un bolt the external alarm siren..

Aug 30, 2009 | Subaru Legacy Cars & Trucks

2 Answers

Hold light on console


The hold light is probably for a fault in the HILL HOLDER SYSTEM

This system holds the Forester on a hill without using the brake pedal, as long as you keep the clutch depressed. It's very useful when towing.

I will check my workshop manual as soon as I have some free time and try to get a definitive answer for you.

Regards,
Andy, Derbyshire UK

Nov 30, 2008 | 1998 Subaru Forester

1 Answer

Windshield of subaru legacy 1998


VYRON, the best place to buy the windshield price wise would be an auto salvage yard. Many have an internet database they can check to look for your windshield at other salvage yards, so you don't have to run around to different places looking, they will locate it for u. good luck, let me know how u make out. countrycurt0

Sep 19, 2008 | 1998 Subaru Legacy

Not finding what you are looking for?
1998 Subaru Legacy Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

Marvin
Marvin

Level 3 Expert

85161 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...