What is the procedure for replacing the pressure hose on the power steering pump for a 2004 pontiac montana?

SOURCE: high pressure power steering hose on a 1995 surburban

PUMP R&R PROCEDURE at Bottom


Do I need to pull the power steering pump off of the 1995 surbuban 350 engine in order to replace the high pressure hose?<-You Ask.

NO Not on the 95 and If you do need or want to REMOVE the PUMP it Comes off Without the Removal of P/S Pump Pulley. Now if you are replacing the P/S Unit Yhere is A Special tool fo pull off Pulley .
Ist a Universal tool for Ford & GM just P/S Pump Pulley Removal Tool Auto Zone has en for $40.00 or rent it from them.

POWRE STEERING PUMP R&R

Removal/Installation Notes

1. Disconnect hoses at power steering pump, then plug pump ports and hoses to prevent dirt entry.
2. Loosen pump adjusting bolt and remove pump drive belt.
3. Remove pump to support bracket retaining bolts, then the pump.
4. Reverse procedure to install.

SOURCE: My power steering pressure hose has a leak.

i pERSONALY WOULD REPLACE IT MYSELF EVEN WITHOUT MY 30yrs Of Experience in this Field. I have Enclosed Instructions for you to use. PLEASE dont Forget to RATE me As MOST folks DONT remember to that is how WE Get our Ratings such as GURU THANK YOU and Good Luck On The Job, Dont PAY a dime If YOU CAN > D I Y

REMOVAL PROCEDURE

1. Remove the power steering pressure hose (2) from the power steering pump (1).
2. Raise the vehicle on a hoist. Refer to Vehicle Lifting.
3. Remove the front exhaust pipe, automatic transmission only. Refer to Intermediate Pipe Replacement in Exhaust System
4. Remove the power steering pressure hose (1) from the power steering gear (3).
5. Remove the power steering hose retainer (2).
6. Remove the power steering pressure hose (1) from the vehicle
   1. Install the power steering pressure hose (1) to the vehicle
   2. Install the power steering hose retainers (2). NOTICE: Refer to Fastener Notice in Service Precautions.
   3. Install the power steering pressure hose (1) to the power steering gear (3). Tighten the fitting to 27 Nm (20 ft. lbs.).
   4. Install the front exhaust pipe, if removed. Refer to Intermediate Pipe Replacement in Exhaust System.
   5. Lower the vehicle.
      1. Install the power steering pressure hose (2) to the power steering pump (1). Tighten the fitting to 27 Nm (20 ft. lbs.).
      2. Bleed the power steering system. Refer to Bleeding Power Steering System in Service and Repair of Steering.

SOURCE: How do you replace power steering hoses on 1999 Alero with 3.4l

disconnect battery make sure your radio is turn off first so you want lose radio code. you have to reprogram it again before it plays. you need to remove drive belt . alternator and air filter. to get your arm to it.have to remove the lower transmission mount its going to be in your way.remove power steering fluid with a siphoner or large syringe. good luck.

Brandon Johnson

• 253 Answers
• Posted on Aug 09, 2009

SOURCE: Power steering pump replacement for Subaru Outback

REMOVAL

1. Remove ground terminal from battery.
2. Remove pulley belt cover bracket.

1. Loosen lock bolt and slider bolt and remove power steering pump drive V-belt.
2. Disconnect connector from power steering pump switch.

1. Disconnect pipe C and suction hose from oil pump. CAUTION:

• Do not allow fluid from the hose end to come into contact with pulley belt.
• To prevent foreign matter from entering the hose and pipe, cover the open ends of them with a clean cloth.

1. Remove bolts which install power steering pump bracket.

1. Place oil pump bracket in a vise, remove two bolts from the front side of oil pump. CAUTION: Do not place oil pump bracket directly in the vise; use soft pads and hold oil pump lightly to protect the pump.

1. Remove socket from oil pump.
2. Remove bolt from the rear side of oil pump.

SOURCE: How to replace high pressure hose on steering,

Found a diagram online myself..