Cars & Trucks Logo

Related Topics:

John TePaea Posted on Jan 07, 2017

How to replace spigot bearing on a 95 hyundai excel

4 Related Answers

Anonymous

  • 1 Answer
  • Posted on Nov 08, 2008

SOURCE: will a 95 hyundai gearbox fit into a hyundai excel 98

of course it will you ******** eventually give us time

Ad

Anonymous

  • 132 Answers
  • Posted on Nov 25, 2008

SOURCE: Hyundai excel x3 front wheel

soak good with wd40 first then use a short piece of wood and a hammer to belt them off careful not to hit the axle with the hammer hope this helps glenn..........

Anonymous

  • 1 Answer
  • Posted on Jan 25, 2009

SOURCE: I have a Hyundai excel

do you know somebody to fix my rear brake

Anonymous

  • 3 Answers
  • Posted on Apr 21, 2009

SOURCE: 95 Hyundai Excel, When you accelerating and de-accelerating

you have bad front end components.such as tie rods,cv axles,and possible bad motor mounts

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Can I use unleaded petrol in my 95 hyundai excel?

Yes 1975 is when they started phasing out leaded gasoline in car engines.
0helpful
1answer

Is there a trick to install the throwout bearing in a 2003 hyundai elantra?

Without fitting a new bearing to the release fork it is virtually impossible however, i managed to put one together by cutting an inspection hole just big enough to get your hand inside above the slave cylinder and manually meshing the release fork, bearing and spigot shaft simultaneously
0helpful
1answer

The belt on the airconditioner in the hyundai excel 1997 is making a squealing noise it seems to be coming from the tension pulley

it could be that the bearing in the tensioner has run dry of lubricant,it may be possible to take it off & grease it,some you can & some you cant so it may have to be replaced.......hope this helps.....cheers
2helpful
2answers

How d i change a clutch in a hyundai excel 1994

We start by removing front Constant Volocity Joints then dropping the transmision to access the cluch assembly then we remove the pressure plate then clutch disk is removed be advized since your replacing the cluck replace hardware too e.g. clips and thrust bearing and pilot bearing to complete the job! good luck!
1helpful
1answer

95 Hyundai Excel, When you accelerating and de-accelerating

you have bad front end components.such as tie rods,cv axles,and possible bad motor mounts
0helpful
2answers

I have a Hyundai excel 97, 5 speed manual, the thrush bearing sleeve is gone, can this just be replaced or do I have to get whole new gear box ? Is there any other model of hyundai gear box that I can use...

Should be able to replace the thrust, or clutch release, or throw-out bearing assy only, (all names i've heard it called over the years )but take a good look at clutch assy, just in case it's time & you want to save yourself R&R transmission twice in a short time.
0helpful
1answer

Hyundai excel x3 front wheel bearings hub stuck on cant remove how do i get the hub off in order to replace the wheel bearings

soak good with wd40 first then use a short piece of wood and a hammer to belt them off careful not to hit the axle with the hammer hope this helps glenn..........
0helpful
1answer

Will a 95 hyundai gearbox fit into a hyundai excel 98

of course it will you ******** eventually give us time

Not finding what you are looking for?

39 views

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...