Question about 2001 Subaru Outback

Open Question

We have a 2001 Subaru Outback with a Cool Start 34TX remote start. the car will start run for lees than a minute will do the same 2 more times before it stops altogether. Is there a solution? Thanks

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 132 Answers

SOURCE: subaru 2000 outback cooling fan never stops

Replace the cooling fan sensor.

Posted on Mar 26, 2009

Ad
emissionwiz
  • 85160 Answers

SOURCE: odometer light burned out 2001 subaru outback

U will need to pull the instrument cluster out and replace the light bulb for the odometer display.

Posted on Apr 27, 2009

subytech1
  • 251 Answers

SOURCE: Power steering pump replacement for Subaru Outback

REMOVAL

  1. Remove ground terminal from battery.
  2. Remove pulley belt cover bracket.



  1. Loosen lock bolt and slider bolt and remove power steering pump drive V-belt.
  2. Disconnect connector from power steering pump switch.



  1. Disconnect pipe C and suction hose from oil pump. CAUTION:
    • Do not allow fluid from the hose end to come into contact with pulley belt.
    • To prevent foreign matter from entering the hose and pipe, cover the open ends of them with a clean cloth.



  1. Remove bolts which install power steering pump bracket.



  1. Place oil pump bracket in a vise, remove two bolts from the front side of oil pump. CAUTION: Do not place oil pump bracket directly in the vise; use soft pads and hold oil pump lightly to protect the pump.



  1. Remove socket from oil pump.
  2. Remove bolt from the rear side of oil pump.

Posted on Aug 09, 2009

  • 1986 Answers

SOURCE: check engine light on in 2001 subaru outback - car

If the light was flashing when it came on, then it means your engine is misfiring.

A solid light can mean anything from a loose/faulty gas cap to a transmission issue.

This light comes on when the computer detects a fault of some sort in its diagnostic tests. If it keeps detecting this issue, the light will remain on. If the light turns off, then it has detected that the issue may no longer be present.

In order to find out what the exact reason was for your light, You need to have your car computer scanned to retrieve the code that the computer would have stored when the light triggered. Most garages will do this free of charge. The code will tell you what may have caused the light to initially turn on.

Posted on Oct 22, 2009

Testimonial: "thanka "

techbuster
  • 5081 Answers

SOURCE: how do u put timing belt for 2001 subaru outback

This is not your average timing belt replacement due to being a double overhead cam that is also an interferance fit.First remove cooling fans.2-Loosen drive belts and remove.3-Remove crank pully.4-Remove timing covers.You will see 4 cam sprockets.Theses sprockets contain single and double referance marks.You will be using the double referance marks.Rotate engine until the double referance marks are facing each other.This is to be done the same way that the American autos timing Chain systems are done but you will have 2 small double lines to line up not dots.The next step is the most important step and is of utmost imortance.THE CAMSHAFT HAVE TO BE LOCKED IN PLACE--FAILURE TO DO SO CAN RESULT IN BENT VALVES.The cam sprocket holders can be bought or rented.You can make your own as well by making 2 wedges with bolt through the middle.Slip in between sprockets and tighten enough to hold sprockets.Do not use excessive torque while tightening wedges sprockets are not made of steel but rather a composite material.Next you will have to remove the tenioner.The tensioner has to be retracted and pin istalled to hold in retracted position.The tension device has to be retracted with care or will be damaged.You can not exceed 50 pounds pressure on the plunger.The simplest method is to reract while still in vehicle, it takes 15 minutes to properly retract the plunger.By pulling up on the tensioner by hand with about 18 pounds of force --50 will be exerted at the plunger.When fully retracted insert pin to hold in reracted position.Next check to make sure that cam wedges are holding and no sprocket are trying to move,when satisfied remove one of the rollers at the bottom on the side where you left hand would be standing in front.Pull off belt.Replacement belt will have referance marksone line will go to crank sprocket face up others will line up with other sprocket marks.Reinstall roller followed by tensioner then pull pin you have holding tenioner retracted.Remove wedges.Reinstall covers fans belts.Do not be intimitaded by this replacement.Everything is very easy to get to.Be sure cams are locked and that damage is not done to tensioner and it is straight forward.

Posted on Nov 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 subaru outback key will not release,car will not start,car in park


Press the brake, wiggle the steering wheel back and forth, and turn the key,sometimes the pin that locks the steering wheel gets stuck if the car is shut off with the wheels in a bind. I hope this is helpful.

Mar 30, 2015 | 2001 Subaru Outback

1 Answer

Why does our 2002 subaru outback sometimes refuse to start and other times starts right up?


Get a $10 MAF CRC cleaner to clean MAF sensor and throttle body, start here first since it's cheap.

Aug 12, 2014 | 2002 Subaru Outback

1 Answer

When I first start driving my 2001 Outback it steers easily. As the car warms up it becomes harder to steer?


rack and pinion leaking internally. Fluid gets hot/warm, gets thinner, then starts to bypass seals and such in the rack/pinion or pump.

Dec 16, 2013 | 2001 Subaru Outback

1 Answer

Low fuel pressure light 2001 subaru outback


Hi have you changed your fuel filter lately? That would be where i would start first, other causes could be fuel pump or blocked fuel lines, but i would start with a new fuel filter as thats the easiest, cheapest option

Apr 14, 2012 | 2001 Subaru Outback

Not finding what you are looking for?
2001 Subaru Outback Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...