Cars & Trucks Logo

Related Topics:

How do you do timing on v6 mazda tribute aj engine petrol

5 Related Answers

Anonymous

  • 491 Answers
  • Posted on Jan 25, 2009

SOURCE: does a 2005 mazda tribute 2.3 having timing belt or chain

a belt

Ad

Anonymous

  • 275 Answers
  • Posted on Jan 20, 2010

SOURCE: 2003 Mazda Tribute will start, idle rough for a

check the fuel filter air filter and vacuume lines if they all good make sure the spark plugs are making a bright blue spark

Anonymous

  • 60 Answers
  • Posted on May 22, 2010

SOURCE: 2004 Mazda Tribute V6 will not stay running

Try this, it's cheap, easy and it won't take long...and it will probably help...

I have a 2001 Tribute and ithas had this problem since about 1 year after buying it new. My motherin law also has one and it has the exact same problem. You can crankthe car2_bing.gifcold (sometime even warm) and it will die unless you keep the gas pedal pressed in. I suspect that this is a widespread problem with theTribute. Forget about the Mazda dealer helping. There is a very simpleand cheap solution:

1. Locate the idle air controlvalve...looking at your engine from the front of the car2_bing.gif, the valve islocated on top of the air intake towards the far right corner of theengine (next to the plastic cover on top of the engine). The valve ismetal, looks like a small metal cylinder is attached to it, and isbolted on with two bolts. It also has wires plugged into it. You can goto google images2_bing.gif and type "Mazda tribute idle air control valve" to see what it looks like.

2. With engine off, unplug the wires from the valve.

3. Remove the two bolts and take valve off of air intake.

4.Inside the metal part you removed, you will see two chambers with ashaft going through them that can extend back and forth. The shaft hasa spring on it, and a plug that can open or plug a hole between the twocavities. This is the idle control valve.

5. Take a flat headscrew driver and pry the shaft back and forth a few times to free itup. There will probably be some dirt/grime on the shaft.

6. Takecarburetor cleaner and spray it in the valve cavities. Allow it to soakfor a minute and drain it out. Repeat if needed to clean it out.

7. Blow in it to dry it out.

8. Take WD40 and spray it in the cavities. Drain excess out
.
9. Take the screwdriver and work the shaft back and forth a few more times. The shaft should move freely.

10. Bolt the valve back onto the engine air intake and plug the wires back up to it.

Startthe engine. If this was the problem, and the engine was stalling justbefore doing this procedure, then it should start right up and idlefine. If it was stalling sporadically when started, it should not anymore. I have to do this procedure with my car every 6 - 12 months. Whenthis problem first occurred with my car it took it to the dealerseveral times. Of course it would not do it at the dealer, and theyclaimed ignorance as to the cause. I suspect this is a cash cow forMazda.

ZJLimited

ZJ Limited

  • 17989 Answers
  • Posted on Dec 10, 2010

SOURCE: need a pic of firing

For 2004 Mazda Tribute 4WD 3.0 liter DOHC V-6 check...

zjlimited_61.gif


Hope this helps (remember to rate thsi asnwer) TY for using Fixya.

Anonymous

  • 4803 Answers
  • Posted on Dec 18, 2010

SOURCE: wheres the spark plugs on

They are under the ignition coils on each side of the engine. The left bank (front of engine compartment)can be relaced by removing the plastic cover then removing the connectors and bolts from the 3 ignition coils. The right bank (rear of engine compartment requires removal of the upper intake plenum to acess the coils.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

2002 Mazda Tribute. How to replace thermostat Housing please?

I need help replacing my thermostat on my 2004 Mazda

JustAnswer https://www.justanswer.com > Mazda Repair
Dec 2, 2015 - The thermostat housing is bolted with 3 bolts to the end of the head closest to the drivers side fender. Thanks for letting me assist you. I ...

1 answer · Top answer: Welcome, I'm Chris and independent contractor that helps customers here. The best way to flush ...

Thermostat replacement Mazda Tribute 2001 - 2011

Haynes Manuals https://haynes.com > en-au > tips-tutorials > mazda-tri...
Free advice from Haynes' master mechanics. Full repair guide available for this vehicle. Save time and money with the experts at Haynes.

Need to replace thermostat in my 2005 mazda tribute 2.3.

JustAnswer https://www.justanswer.com > Mazda Repair
Oct 20, 2022 - 1. Drain the engine coolant. 2. Remove the accessory drive belt tensioner. 3. Remove the thermostat and thermostat housing assembly. ^ Loosen ...

1 answer · Top answer: Good Afternoon, my name is ***** ***** ill be helping you, so sorry to hear about the issues ...

How to change MAZDA TRIBUTE Thermostat

AUTODOC UK https://club.autodoc.co.uk > ... > Thermostat > MAZDA
Illustrated step-by-step manuals and video tutorials on replacing MAZDA TRIBUTE Thermostat will tell you how to carry out DIY replacement of parts and ...

Mazda Tribute Thermostat Housing Pipe Water Outlet V6 ...

Parts Factory https://partsfactoryaus.com.au > product > mazda-tribute-...
Nov 22, 2023 - Mazda Tribute Thermostat Housing with a Replacement Warranty of 3 Years. Our Video Tutorials allow people to save Thermostat replacement cost.
Review by Jay · ‎ A$95.00 · ‎ In stock ..
0helpful
1answer

What's your question? my mazda tribute v6 petrol was serviced and the engine was washed. but since then I'm having a problem of back firing, and it can't even rave. what could be the problem?

Hello Prosper, It sounds like you have wet spark plug wires. You can let it sit overnight and see if that dries it out or you can spray some water displacing solvent like WD40 on it it help eliminate the water.
0helpful
1answer

WHAT IS A PVC HOSE IN MAZDA MPV

The PCV is a valve and a hose, that sucks engine ring bypass gasses and reburns them. if it plugs up the engine leaks oil.

if the hose cracks it sucks air and the AFR goes lean and bucks.

jerks.

only on engines (unstated) that use a MAF sensor.

engine that use a MAP sensor ,race too fast with full power and no jerk with air leaks.

next time post engine type. as we can not guess this.



the list.....



2.0 L FS-DE I4 (99-02)

2.3 L L3-VE I4 (02-05)

2.5 L GY-DE V6 (99-01)

2.5 L AJ V6 (99-02)

3.0 L AJ V6 (02-06)

2.0 L RF MZR common rail turbodiesel









WHAT ENGINE PLEASE.

if unsure, (why fix any engine,if unsure>)but in the USA

the hood EPA sticker states this clearly.

no engine , no country, no joy,
1helpful
1answer

Mazda tribute v6 engine no

The engine number is recorded on the original factory invoice from Mazda to the dealer who received the Tribute from the factory. This is true in Canada for sure and I imagine it would be common for all Mazdas.
0helpful
1answer

2001 mazda tribute v6 probumes

Is it the seat belt warning?

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

0helpful
1answer

Does 2001 Mazda Tribute V6 engine have a serpentine belt

Yes, but it uses a timing chain for the valves
8helpful
2answers

DOES THE V6 MODEL HAVE A TIMING CHAIN OR BELT?

A 2002 Mazda MPV 3.0 V6 has a timing chain

Please rate me if you are staisfied with the answer.
9helpful
1answer

Mazda tribute firing order. I have miss fire in the # 5 but I dont have the order.

You didn't post your engine size so please pick the applicable diagram:

2001 Mazda Tribute DX 2WD
3.0 liter DOHC V-6

27a11e1.gif

2001 Mazda Tribute DX 4WD
2.0 liter DOHC L4

f205155.gif
2wd or 4wd...it is still the same for the V6.
Not finding what you are looking for?

115 views

Ask a Question

Usually answered in minutes!

Top Mazda Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...