1975 chevy c-20 truck power steering mounts

The pump will bolt to the bracket, then you will have two bracket bolts to the water pump and another bracket bolt to a bracket attached to one of the exhaust manifold bolts.

remove the nuts holding the mounts .jack up the engine .or better to hire an engine lift.

5) Install the rear A/C mountingbracket. Tighten the rear A/C mounting bracket bolts to 35 Nm (26lb-ft).6) Install the A/C compressor. 7) Install the power steering pump. 8) Connect the negative battery cable.
If this helps, please say so! Thanks! :-)

Yes there is complete guide available for power steering pump and bracket positions mounting.Its will all details and diagram and lot more details.Please click on link below.Check the details http://technoanswers.blogspot.com/2011/03/1989-dodge-dakota-2wd-4cylinder-25.html ------------------ In this link is complete guide for steering and suspension of 1989 Dodge Dakota 2wd - 4cylinder 2.5------------------ This should help. Thanks.Helpmech.

Belt Installation, Aerostar 4.0L Engine





Item Part Number Description 1 8620 Drive Belt 2 N606068 Bolt 3 10300 Generator 4 10153 Generator Mounting Bracket 5 8509 Water Pump Pulley 6 6B209 Drive Belt Tensioner 7 N800199 Screw 8 8678 Belt Idler Pulley 9 N802096 Screw 10 19703 A/C Compressor 11 2882 A/C Compressor Mounting Bracket 12 3C718 Brace 13 N806020 Bolt 14 3A674 Power Steering Pump 15 3A733 Power Steering Pump Pulley 16 N800199 Screw 17 N606572 Bolt 18 N620481 Nut 19 8501 Water Pump 20 6312 Crankshaft Pulley A - Belt Tension Check (See Specifications) B - Tighten to 40-55 Nm
(30-41 Lb-Ft) C - Tighten to 24-30 Nm
(18-23 Lb-Ft) D - Tighten to 21-29 Nm
(15-21 Lb-Ft) E - Tighten to 40-50 Nm
(30-37 Lb-Ft)

Belt Installation, Ranger and Explorer 4.0L Engine





Item Part Number Description 1 8620 Drive Belt 2 10300 Generator 3 8678 Belt Idler Pulley 4 19703 A/C Compressor 5 3A733 Power Steering Pump Pulley 6 8501 Water Pump 7 6312 Crankshaft Pulley 8 6B209 Drive Belt Tensioner 9 N806020 Bolt 10 2882 A/C Compressor Mounting Bracket 11 3A674 Power Steering Pump 12 N606572-S2 Bolt 13 N800199-S8M Bolt 14 N620481-S2 Nut 15 3C718 Brace 16 N606068 Bolt 17 10153 Generator Mounting Bracket 18 8509 Water Pump Pulley 19 N605805-S2 Bolt A - Belt Tension Check (See Specifications) B - Tighten to 21-29 Nm
(15-21 Lb-Ft) C - Tighten to 40-55 Nm
(30-41 Lb-Ft)

Belt Installation, Ranger 2.3L Engine





Item Part Number Description 1 8678 Belt Idler Pulley 2 10300 Generator 3 8509 Water Pump Pulley 4 3A733 Power Steering Pump Pulley 5 2E884 A/C Clutch Pulley 6 6312 Crankshaft Pulley

Belt Installation, Aerostar 3.0L Engine





Item Part Number Description 1 10300 Generator 2 3F671 Belt Idler Pulley 3 3A733 Power Steering Pump Pulley 4 6B209 Drive Belt Tensioner 5 6312 Crankshaft Pulley 6 8509 Water Pump Pulley 7 19703 A/C Compressor

1. Remove serpentine belt

2. loosen power steering pressure and return hoses

3. Remove nut from pressure line mounting on alternator bracket

4. remove power steering pump mounting bolts.

5. Lift pump assembly from engine mounting and remove hoses.

6. Reverse order to install. Fill and bleed system.

NOTE: A new or rebuilt power steering pump will most likely not come with a pulley attached. You will need a power steering pulley remover/installer tool to transfer the pully from the old pump to the new one.

POWER STEERING PUMPS FOR THE 400 AND 350 CHEVY ENGINES ARE HELD IN PLACE IN A BRACKET AND BRACE MOUTED TO THE ENGINE.CHECK AROUND ON LINE ON INTERNET LOOK UP POWER STEERING PUMP MOUNTING BRACKETS FOR 400 CHEVY ENGINE.YOU NEED THE MOUNTING BRACKET IN ORDER TO INSTALL POWER STEERING PUMP.

Removal & Installation

2.0L Engine

1. Disconnect the negative battery cable.
2. Remove air intake resonators.
3. Remove the air cleaner-to-throttle body tube and the mass airflow sensor.
4. Unplug the connectors and remove the cables from the alternator.
5. Raise and support the vehicle.
6. Release the drive belt tensioner and remove the drive belt from around the alternator.
   NOTE It is not necessary to remove the drive belt from the engine.
   
7. Remove the alternator mounting bracket bolts and remove the mounting bracket.
8. Lower the vehicle.
9. Remove the power steering pressure hose bracket retaining nut and bolt and remove the bracket with the hose from the engine lifting eye.
10. Remove the alternator mounting bolts and remove the alternator from the vehicle.
12. To install:
    
    1. Place the alternator into position and install the mounting bolts finger tight.
    2. Install the power steering hose bracket and tighten the retaining nut and bolt to 70-106 inch lbs. (8-12 Nm).
    3. Raise and support the vehicle.
    4. Install the alternator mounting bracket and retaining bolts and tighten to 15-22 ft. lbs. (20-30 Nm).
    5. Release the drive belt tensioner and install the drive belt pulley over the alternator pulley.
    6. Lower the vehicle.
    7. Tighten the alternator mounting bolts to 15-22 ft. lbs. (20-30 Nm).
    8. Install the alternator connectors and the cables. Tighten the terminal nut to 80-97 inch lbs. (9-11 Nm).
    9. Install the air cleaner-to-throttle body tube, mass airflow sensor, and the air intake resonators.
    10. Connect the negative battery cable. To install:
        
        1. Place the alternator into position and install the mounting bolts finger tight.
        2. Install the power steering hose bracket and tighten the retaining nut and bolt to 70-106 inch lbs. (8-12 Nm).
        3. Raise and support the vehicle.
        4. Install the alternator mounting bracket and retaining bolts and tighten to 15-22 ft. lbs. (20-30 Nm).
        5. Release the drive belt tensioner and install the drive belt pulley over the alternator pulley.
        6. Lower the vehicle.
        7. Tighten the alternator mounting bolts to 15-22 ft. lbs. (20-30 Nm).
        8. Install the alternator connectors and the cables. Tighten the terminal nut to 80-97 inch lbs. (9-11 Nm).
        9. Install the air cleaner-to-throttle body tube, mass airflow sensor, and the air intake resonators.
        10. Connect the negative battery cable.
        
        
        

Here are some. Hope it helps =D

Timing Marks

Diagram

TORQUE SPECIFICATIONS
Application Ft. Lbs. (N.m)
A/C Compressor Bracket Bolt 37 (50)
Alternator Bracket Adjuster Bolt 16 (22)
Alternator Bracket Bolt 33 (45)
Balance Shaft Pulley Bolt 22 (30)
Camshaft Pulley Bolt
2.2L DOHC 37 (51)
2.2L SOHC & 2.3L 27 (37)
Crankshaft Pulley Bolt 184 (250)
Power Steering Belt Adjuster Nut 11 (15)
Power Steering Pump Bracket Bolt 33 (45)
Power Steering Pump Mounting Bolt 16 (22)
Shift Cable Bracket Bolt 16 (22)
Timing Belt Tension Adjuster 33 (45)
INCH Lbs. (N.m)
Timing Belt Cover Bolt 108 (12)
Valve Cover Nut 90 (10)
Water Pump Bolt 108 (12)

BELT, REPLACE

1. Release belt tension and remove belt from power steering and alternator pulleys. Twist belt to get between tensioner and front cover and between power steering pulley and engine mount bracket.
2. Raise and support vehicle.
3. Turn wheel to the extreme right and remove right side splash shield.
4. Remove belt from crankshaft and A/C compressor pulleys. Twist belt to get between idler pulley and engine mount bracket.
5. Lower vehicle.
6. Twisting new belt to get past the front cover, install belt around power steering pump pulley, Fig. 15. Allow belt to hang free.
7. Twist belt to get between tensioner and front cover, wrap belt around alternator.
8. Remove belt from power steering pulley and set aside.
9. Raise and support vehicle, then twist belt to get between tensioner and front cover, wrap belt around crankshaft and A/C compressor pulleys.
10. Install right side splash shield and lower vehicle.
11. Position belt around power steering pulley and release tensioner.