Torque specs for cylinder head bolts on a 2008 gmc canyon 3.7 5 cyl.

limited info generic answer if looking for all specs then buy a repair manual multi sites online can download or hardcopy -

2003 Cadillac CTS V6-3.2L VIN N - Justanswer

http://ww2.justanswer.com > uploads > joecamel90
PDF
Apr 16, 2010 - Tighten the cylinder head bolts to 25 Nm (18 ft. Tighten the cylinder head bolts to 90 degrees using the J 36660-A. Tighten the cylinder head ...
6 pages

What Is the Torque for the Heads - 2CarPros

https://www.2carpros.com > ... > Cylinder Head > Torque
Jun 29, 2010 - MEMBER; 2003 CADILLAC CTS; 6 CYL; 2WD; AUTOMATIC; 100,000 MILES. I am repairing the heads of this car. whats the torque I need to apply?

Complete Torque Specs List ' Cadillac CTS-V Forum

https://www.ctsvowners.com > threads > complete-torqu...
Jul 1, 2013 - Cylinder Head Core Hole Plug: 15 lb ft. Drive Belt Idler Pulley Bolt: 37 lb ft. Drive Belt Tensioner Bolts: 37 lb ft. Engine Block Coolant ...
Torque Specs??? - Cadillac CTS-V Forum
Apr 4, 2012
Torque Specifications ' Cadillac CTS-V Forum
Mar 8, 2012
Engine bolt torque specs, other - Cadillac CTS-V Forum
Nov 24, 2015
Factory head bolts reused ' Cadillac CTS-V Forum
Sept 11, 2014
More results from www.ctsvowners.com

Question edited to remove chaos :>D
Question moved to sub category.

https://www.google.com/search?q=2015+Mercedes+Benz+OM651+CDI+4+cyl+2.1+diesel%2C+cylinder+head+bolt+torque

..

Follow these steps:
1. Tighten the cylinder head bolts to 44 ft-lbs (60 N-m)
2. Rotate the cylinder head bolts another 95 degrees
3. Now tighten them an additional 95 degrees
4. You are done!

Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:

1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
2. Step 2: Bolts 1-10 verify torque without loosening
3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)

well it's at alldata.com and at suzuki pitstop plus dot com.
here ill do that for you....
4 banger no displacement stated, now that is a challenge.


now the words..... USA car... 2.0L vin Z

Cylinder head bolts. Tighten the cylinder head bolts gradually and in the sequence shown. Tighten the cylinder head bolts to 18 ft. lbs. (25 Nm) and turn the bolts another 3 turns of 90 degrees using the angular torque gauge KM-470-B.

Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

cylinder head the torque is : step 1 55 ft-lb, step 2 65 ft-lb, step 3 85 ft-lb. Rocker arm stud nut or bolt is 17 to 23 ft-lb. and valve cover bolt 72 to 108 in-lb.

Cylinder head bolts are done in 3 steps. Step 1 - 20 ft.-lbs
Step 2 - 50 ft.-lbs
Step 3: Tighten an additional
90 degrees.
Lifter guide plate bolts 18 ft-lbs
Rocker arm shaft bolts 40 ft-lbs
Hope this helps.

Step 1 14 ft.lbs
Step 2 29 ft.lbs
Step 3 36 ft.lbs
Step 4 loosen 3 revolution and torque in sequence, one bolt at a time, and torque to next step.
Step 5 short bolts 15-32 ft.lbs
long bolts 30-36 ft.lbs
Step 6 additional 175-185 degrees.