Cars & Trucks Logo

Related Topics:

N
Nikolao Faasala Posted on Dec 15, 2016

I need help with timing mark for camshaft and crankshaft on 2004 dodge ram 1500 5.7 hemi

5 Related Answers

Anonymous

  • 2920 Answers
  • Posted on Jan 26, 2009

SOURCE: Dodge Ram 1500 can it have a plow?

if you do it do it at the dealer that you got it from so it wont void the warranty. that way you keep it in place and they can also tell you the specifications as to what you need to do ,if anything to the front of the truck

Ad

Dave Leoni

  • 66 Answers
  • Posted on Jun 03, 2009

SOURCE: Need diagram to install serpentine belt on 2004

There should be a diagram under the hood on the fan shroud or radiator support. If not, let me know and I see if I can find one. For the most part, if the pulleys it rides on are grooved, the belt ribs ride on it, it the pulley is smooth, the back side rides on it. From a picture of the alternator I have, from the passenger side coming up, over the alternator, then down and under the belt tensioner (smooth pulley), then up and over A/C compressor, then down and around P/S pump, up and around water pump, down around crankshaft pulley.

emissionwiz

Marvin

  • 85242 Answers
  • Posted on Jul 01, 2009

SOURCE: When is it time to tune-up a 2004 Dodge Ram 1500

1st tune (spark plugs) is 100,000 miles air and fuel filters every 30,000 miles

Anonymous

  • 1129 Answers
  • Posted on Sep 12, 2009

SOURCE: 2004 ram 1500 with 5.7 hemi using 1 quart every 3,000 miles

Slide a large piece of cardboard under the truck after driving for ten minutes note in which area directly above the spot on the cardboard the oil is coming from then get under the vehicle with a drop light to look for the origin of the leak, if no leak is detected then it may be the engine is burning oil this could either be valve stem seals or broke or worn oil rings.

Anonymous

  • 249 Answers
  • Posted on Jan 05, 2010

SOURCE: replace timing chain on 03 dodge ram 1500 with 5.7 hemi

i have an 02 and i purchased a repair manual from autozone

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer
1helpful
1answer

How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter

Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


26002143-2qxw3km0vcnqu3setvnduoab-2-1.gif
0helpful
1answer

2004 Dodge Ram 1500. Camshaft position sensor location please?

Old question resurrected by Mark Duncan! :>D Mark, post as a new post please. That section is for asking the OP for further information on HIS problem.

Question edited for clarity.
Question moved to sub category.

Camshaft Sensor Location

https://www.google.com/search?q=2004+Dodge+Ram+1500.+Camshaft+position+sensor+location

..
0helpful
1answer
3helpful
1answer

Replace timing chain on 03 dodge ram 1500 with 5.7 hemi

i have an 02 and i purchased a repair manual from autozone
0helpful
1answer

2004 dodge ram hemi wont always start up

this is your camshaft pos. sensor
2helpful
1answer

2004 Durango 5.7 timing gear alignment

  1. If tensioner assembly is being replaced, install tensioner and mounting bolts. Torque bolts to 28 Nm (250 in. lbs.) .
  2. Retract tensioner if required. CAUTION: The camshaft pin and the slot in the cam sprocket must be clocked at 12:00. The crankshaft keyway must be clocked at 2:00. The crankshaft sprocket must be installed so that the dots and or paint marking is at 6:00.
  3. Place both camshaft sprocket and crankshaft sprocket on the bench with timing marks on exact imaginary center line through both camshaft and crankshaft bores.
CAUTION: The timing chain must be installed with the single plated link aligned with the dot and or paint marking on the camshaft sprocket. The crankshaft sprocket is aligned with the dot and or paint marking on the sprocket between two plated timing chain links.
b04dbf8.jpg
Not finding what you are looking for?

388 views

Ask a Question

Usually answered in minutes!

Top Dodge Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...