1998 Mercedes-Benz CLK Logo
Anonymous Posted on Jul 20, 2009

CLK 280 MBZ brake left lamp on indicator is being displayed

I have a 2007 CLK 280 MBZ.When I start the car I get themessage "brake left lamp is on:. I looked at the manual and dont know what to do with this and how to turn it off. It is not a warning signal.Plz help

2 Answers

ROB

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Vice President:

An expert whose answer got voted for 100 times.

  • Master 858 Answers
  • Posted on Jul 20, 2009
ROB
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Vice President:

An expert whose answer got voted for 100 times.

Joined: Jul 17, 2009
Answers
858
Questions
0
Helped
328754
Points
2471

Its a warning that the light is stuck on
it could be caused by the earth or grounding is faulty may just need to remove bulb 7 put it bak in it may fix it & the warning should dissapear

Paula Hamilton

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Vice President:

An expert whose answer got voted for 100 times.

  • Mercedes-Benz Master 894 Answers
  • Posted on Jan 10, 2013
Paula Hamilton
Mercedes-Benz Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Vice President:

An expert whose answer got voted for 100 times.

Joined: Mar 13, 2012
Answers
894
Questions
1
Helped
226738
Points
2652

My advice is to get someone to press the brake with ignision switched on,you have a look if there is no light then change the bulb job done,
if the light is permently on try changing the bulb before you start looking for bad earths.
best of luck.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

What is the cylinder firing order for 2006 Mercedes 280 clk

I couldn't find clk 280 in my US database.
I did find 3.0L/2996 cc
The firing order for v6, 143625, 2006 model year. I figured no matter what model had this engine, the firing order would be the same, correct?
1helpful
2answers

Eng code p0355 and p0305 2007 mbz ml350 eng runs rough but after restarting runs ok.

p0355 indicates that engine misfire is present.

p0305 indicates that the misfire is in the cylinder number 5

Have the spark plug tested/replaced and test the cylinder number 5 spark plug coil.
0helpful
1answer
0helpful
1answer

Rattling sound on acceleration and idle,passed smog recently. Have 2003 MBZ clk320

have the following checked:

1. ignition timing
2. valve lifters / tappets
3. rod bearings
0helpful
1answer

2007 Jeep Grand Cherokee right taillight only one NOT working.

When you are using the keyless entry you are flashing the turn signals... which are also the brake lamp filiment.
The park lamps on that side of the car simply dont work.
There is probably an open somewhere in the wire to that lamp. The lamps are fed through the wiring harness on the drivers side. Your break in the line is somewhere between the left and right in the rear. You can try to find it or run a jumper from left to right under the rug and save some pain. Your call.
2helpful
1answer

Changed pads on merc 280 clk and brake pad warning light is still on have not change wires is there reset or must i replace wires

If the brake sensors are rubbed through than you need to change the sensors in order for the light to go out.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

0helpful
1answer

When braking the dash lamp comes on and sounds and the display says either indicator faulty or left brake faulty

This indicates that your brake pads are worn bad enough for the warning light to come on. You need to have new pads put on the front before they dig into the rotors and have to have them turned as well. I would do this asap.
Sincerely,
Shastalaker7
0helpful
1answer

320 clk -98 what is the selusion when Bas-ESP-ABS is showing on my display? even the autodrive function is not working. Jesse

ABS--BAS

Most likely cause is the 'stop lamp switch'
It is a electric switch located on the brake pedal inside the car, about half way up on the brake pedal.
Pretty cheap too, I think the switch is only like $25 bucks.
2 connectors on the switch and then it turns out.
hope that helps

1helpful
1answer

Recall Isuzu i-280

2006 ISUZU I-280 EXTERIOR LIGHTING:BRAKE LIGHTS:SWITCH Recall Date: 04/27/2006 Summary: CERTAIN PICKUP TRUCKS MAY EXPERIENCE THE PERMANENT LOSS OF BRAKE LAMP FUNCTION OR BRAKE LAMPS THAT ARE ILLUMINATED AT ALL TIMES. THE CENTER HIGH-MOUNTED STOP LAMP (CHMSL) IS AFFECTED IN BOTH INSTANCES. ALSO, IF EQUIPPED, THE CRUISE CONTROL WILL BECOME INOPERATIVE. ANY TRAILER BRAKE LAMPS WHICH ARE CONNECTED TO THE VEHICLE'S BRAKE LAMP WIRING WILL MIMIC THE VEHICLE'S BRAKE LAMPS WHEN EITHER CONDITION OCCURS. Consequence: A FOLLOWING DRIVER MAY NOT KNOW WHEN THE BRAKES HAVE BEEN APPLIED, AND A REAR-END CRASH COULD OCCUR WITHOUT PRIOR WARNING. Remedy: DEALERS WILL REPLACE THE BRAKE LAMP SWITCH ASSEMBLY. THE RECALL BEGAN ON DECEMBER 5, 2006. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438; GMC AT 1-866-996-9463 OR ISUZU AT 1-800-255-6727. Potential Units Affected: 404733 Notes: ISUZU I-280 06030
Not finding what you are looking for?

225 views

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

xxxxxx xxx

Level 3 Expert

5117 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...