Question about 1999 Ford Expedition

Open Question

How do you chance a 1999 exprodition eddie bauer neutral safety switch step by step please

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 92 Answers

SOURCE: 1999 expedition 5.4L eddy bauer

check fuses,check power and ground at blower motor.if the blower has only one speed it will mean a resistor is shot.an easy test if blower is not working at all is to turn blower on hi and tap on the bottom of blower motor with hammer if the blower motor kicks in then you know the motor is the problem.if the motor still does not work,the wiring to the switch and the switch will need to be tested,if the wiring and switch are ok,then replace the blower motor.

Posted on Nov 01, 2008

Ad
  • 393 Answers

SOURCE: 1999 ford expedition eddie bauer running board lights

check the door pin switch

Posted on Dec 18, 2008

emissionwiz
  • 85206 Answers

SOURCE: 1999 ford explorer will not shift into reverse?

this is always caused by a failed/worn out reverse clutch pack, you must remove the trans and have it overhauled to correct this failure.

Posted on Apr 18, 2009

canbruce75
  • 1776 Answers

SOURCE: removing neutral safety switch

Check out the autozone website at autozone.com and register your vehicle. It is free and will give you access to an online repair manual for the vehicle. The steps for removing the neutral safety switch can be found there. Hope this helped. Best wishes.

Posted on Aug 03, 2009

jbass706
  • 167 Answers

SOURCE: Location of Shift Solenoid in 1999 Ford Expedition Eddie Bauer?

They are round "cans" with wires attached. You should have SSA, SSB, SSC, Torque converter and Pressure Control solenoids. They control pressures and have no mechanical linkage.

Posted on Oct 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Ford Expedition EL Eddie Bauer.. Console Gear shift. Where EXACTLY is the neutral safety switch located, or does it even have one?


https://www.google.ca/url?sa=t&source=web&rct=j&url=http://www.hillerford.com/v2/resource_library/2008/2008_vehicle_info/2008_expedition.pdf&ved=0CB0QFjABahUKEwiLr_P3xoDIAhXOB5IKHaxbAes&usg=AFQjCNH6m9hQKLrNeNUVsgJrbD02luR1MQ

Sep 18, 2015 | 2008 Ford Expedition El

1 Answer

1999 ford explorer eddie bauer lights


do it with the dash dimmer knob

Sep 14, 2014 | 1999 Ford Explorer

1 Answer

How do i change a neutral safety switch on a 1999 ford expedition eddie bauer 5.4 liter 2 wheel drive


neutral safety switch is attached on the outside of trans. remove the electrical connections. remove the shift cable/linkage arm that is attached to the trans shift rod. remove any other screws or bolt that hold the neutral safety switch. the switch should now slips off the shift rod. attach new part and reinstall.

Aug 28, 2014 | 1999 Ford Expedition

1 Answer

How do i find the location neutral switch on a 1999 Ford expedition eddie bauer 5.5 liter 2 wheel drive


It's on the side of the transmission under the drivers door. The shift cable runs to the control arm it is under.

Aug 28, 2014 | 1999 Ford Expedition

1 Answer

I have a 1995 F-150 Eddie Bauer custom edition truck. It's engine is a 351 Clevland w/ 5 speed automatic transmission and is also 4x4 that can be changed into 4 wheel drive from inside the truck on...


I have a 1999 Eddie Bauer Edition Expedition that has a fob on it that if you remove it will not allow the vehicle to start. Sometimes, my dad bumps it with his knee and the next time he tries to start it it will not start unless it is reconnected by inserting it properly into its receptacle. I'm no sure if you have this set up, though, for the security system.

If it's a neutral safety switch, you might try jiggling the shifter clockwise and counterclockwise while trying to start the vehicle.

Some mechanics with guts would put a screwdriver on the 2 solenoid contacts to bypass the other circuitry in the car to at least make it turn over with the ignition on so that it will start. I'm not sure if that's a route that you want to take though. Maybe, try to get AAA to tow it up to 100 mi. under their plan.

Nov 04, 2011 | 1995 Ford F150 Styleside Regular Cab

1 Answer

My 99 Eddie Bauer Expedition blows cold air when


the heater is a long plastic box and the mixer door is inside of the box. The stepping motor controls the door.

Apr 15, 2017 | 1999 Ford Expedition

1 Answer

1994 bronco eddie bauer. I have no brake lights


I think there are 2 switchs on that brake pedal. You are right tho about the brake switch causing your problem.
If you fix your brake light problem your other problem will be fixed also.. check to see if the wires at the brake pedal switch are energized. I am betting on a ground problem.

Dec 22, 2009 | 1994 Ford Bronco

Not finding what you are looking for?
1999 Ford Expedition Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...