Cars & Trucks Logo

Related Topics:

Anonymous Posted on Nov 25, 2016

2008 GMC Canyon engine air filter replacement

1 Answer

SeabeeMechanic

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • GMC Master 1,367 Answers
  • Posted on Dec 17, 2016
 SeabeeMechanic
GMC Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Apr 22, 2013
Answers
1367
Questions
1
Helped
412581
Points
3754

5 Related Answers

Anonymous

  • 10 Answers
  • Posted on May 27, 2008

SOURCE: 2004 GMC truck

MAY BE A VACUME LINE IS NOT HOOKED UP RIGHT

Ad

scott carlson

  • 60 Answers
  • Posted on Mar 01, 2009

SOURCE: Engine Air Filter

The engine air filter is located in the box behind the battery. This box should have 4 metal clips that pop off and you and pick up the top of the box and underneath is the filter.

Anonymous

  • 1 Answer
  • Posted on Jun 12, 2009

SOURCE: replace passenger side mirror, power

Open the door. Look for a cheap piece of plastic near where the mirror is located. Carefully pry the plastic off. There are 3 bolts. There is a wire harness connector. Unbolt the mirror and unclip the harness. Installation is reverse of removal. Easy job.

Anonymous

  • 1 Answer
  • Posted on Apr 23, 2011

SOURCE: can you change a 2005

yes, the filter is on the frame rail on the left side (driver side)at about the back of the drivers seat

Anonymous

  • 134 Answers
  • Posted on Jun 06, 2011

SOURCE: How do I change the

Looking under the hood, there is a black box on the right with 6 or 8 torx head screws. You will need (I think)T-25 Torx bit and atleast a 6" extension. It still needs to be finnagled out after being unscrewed. It's not too difficult of a task, but may take 20mins or so if you've never done it before.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Got a 2008 gmc canyon had 4x4 light blinking all the time replaced solenoid on transfer case light on 2 wheel press 4x4 it blinks and returns back to 2 wheel 4x4 will not engage

I recommend check outhttps://big-manuals.com/products/gmc-canyon-service-repair-manual-2004-2008
for Wiring, schematic, electrical diagrams, torq setting, error/fault codes, full assembly/dissemble, service instructions and a lot more are basic contents of these online books they here on this website
Must check it out
0helpful
1answer

Why does my GMC Canyon 2008 Blower fan only works on 2?

I had a problem on my 2006 sierra, the fan wouldn't work on 5. gm had a curtisy recall, they had to replace a resistor, at no charge, last week. Ask your dealer about any recall for this with your vehicle.
0helpful
2answers

What is causing low idle on my 2004 gmc canyon

Check air filter ,inspect if there is air leak .clean the throttle body
0helpful
1answer

Where do i find the evap system on a 2008 gmc canyon

the evap system is the vapor control of gasoline in the fuel tank it runs the whole length of the truck involving a vapor canister and vent control valves and purge valves of course hoses also.
3helpful
2answers

GMC Canyon, computer shot.. cost?

You can to the Salvage Yard for a new computer, but your going to have to get it reprogram to your ignition keys, so the Passlock will start the engine. Before you go through all of that. recheck every thing, it could be your crank sensor or your ICM faulty causing your engine to shut down. Keep me posted and let me know what DTC codes you have. Note: a faulty fuel pump or dirty fuel filter will not set a DTC code. You may have a dirty fuel filter or faulty fuel pump or faulty fuel pump wire harness or fuel pump relay.
0helpful
1answer

I have po300 and po506 on my canyon code cleared and resets after a while

From http://www.obd-codes.com/trouble_codes/
The P0300 is a misfire and P0506 indicates low RPM at idle.

A misfire can be caused by poor ignition (spark plug, plug wire, coil, ignition module/engine control module).
OR
Poor air/fuel (air filter, fuel injector, fuel pressure, fuel filter, fuel pump, bad gas, or engine control module).

Check your maintenance requirements and see if any of these items are due for replacement first.
0helpful
1answer

I want to replace the air filter

open hood black box passenger side undo clips replace air filter
0helpful
1answer

2005 gmc canyon

air flow metering valve
0helpful
2answers

2004 GMC truck

MAY BE A VACUME LINE IS NOT HOOKED UP RIGHT
Not finding what you are looking for?

113 views

Ask a Question

Usually answered in minutes!

Top GMC Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...