SOURCE: replace rear seat belt in 1993 Toyota Corolla
OK. On the front edge of the seat bottom cushion, pull up hard, both sides. This will dislodge the 2 clamps that holds the seat cushion to the floor. Pull the seat cushion out & set it aside. You will now see the female latches bolted to the area where the rear of the seat cushion meets the rear seat back bottom. Remove the bolts (14 mm I think).
SOURCE: driver side power seat 2001 Chevy Tahoe
as long as nothing is stuck in track and you hear no noise when using switches, look for broken wire at connector or in harness. ck fuse first of course, if blown, something may be stuck in track causing it to stop and blowing fuse
SOURCE: Fold down rear seats
THE SEAT RELEASES ARE IN THE TRUNK IN THE AREA WHERE THE SPEAKERS ARE NEAR THE EDGE OF THE TRUNK OPENING.
SOURCE: TAKE OUT REAR SEAT ON 2002 JAGUAR X TYPE")
I had the same issue today with a 2004 jag.
1. Once I had the locksmith open the door. We proceeded to remove the back seat. Not an easy task, but this is the only way.
A. remove the plastic kick plate on floor leading to back seat. This will allow you to pull out the padded liner that is not part of the seat but cushions each side. It will not completely come out, but expose a star nut that must be turned loose with six more later on.
b. The front of the back seat is held down by two copper u shaped wires, that must be popped up and out of a white piece of plastic, Once this is done you can lift up the seat portion and remove it from the car. You will now see six star bolts that must be removed. After you take them out the round bar holding the upper portion of the seat can be removed or popped out enough so that you can seperate or spread the back portion of the seat from each other in sections. Once this is done you will be able to pull out a section far enough out to gain access to the trunk.
It takes about 15 minutes once you understand what your doing, and about an hour if you have never done it. The trick is allowing the lock smith to open the car. The alarm will sound off for about 2 minutes then stop. Unless you have the rear center console removalbe panel and arm rest, then the only course is exactly what I did, removing the back seat. They charged me 150.00 dollars with me doing most of the work. Not much I could say, as I was the *** that locked my keys in the trunk. Best bet for a Jag is to carry another key with electronic trunk opener mounted underneath the car in a key lock box. Well worth the investment, as most people end up getting their car towed.
It is poor feature on a Jag that the only way you can get in a locked trunk is through the back seat, but this is how it is done.
Believe me, it is the only way other than having it towed to the Jag dealer so he can figure out. Thier is a way to jump a wire under the passenger side dash, but you may end up shorting out the whole electrical system, I dont think it is worth the risk, unless the person doing it, has previous experince. Hope this helps, and happy tearing out your back seat. You can do it, the first time is always a little tough.
Dsaldo vermont
SOURCE: My 2000 mitsubishi galant trunk
Sorry my friend, I think you won't find one....The best way is to fold back the carpet and locate the end of the broken cable, and then take a pair of pliers and pull the cable from there...
When it comes to replacing the cable it would be easier to remove the front and rear seats enabling better access to the cable....Then fold back more of the carpet.
There is usually a ten millimeter nut holding down the lever.... Remove that and then remove the trunk locking mechanism....That will mean removing two additional ten mil bolts
With those removed unhook the cable from the lock....It will have a small round ball at the cable end. This can easily be removed via the slot provided.
Tape the new cable to the end of the old one....Unhook any outer cable retaining clips you find, so the the cable cannot be caught anywhere.Refit in the cable into the trunk lock mechanism, this so that the cable cannot be pulled all the way through, if you should pull too far....gently pull the cable through
Refit the lever to the floor and then refit the trunk mechanism....The rear cushion is released by pulling upwards and fitted back by locating the retaining tongues into their slots....To remove the front seat, move all the way forward to remove the bolts at the rear of the rails and then slide it back to get the front ones removed....
Sorry I couldn't help any other way....Regards Johngee10
836 views
Usually answered in minutes!
×