1998 grand caravan. I need to get the bench seat side for the quick release Mechanism

We do not sell and install seats.

Seats for Chrysler ' eBay

www.ebay.com/sch/Seats-for-Chrysler/33701/bn_1358665/i.html
eBayGo to My Vehicles .... 2008-2010 Dodge Grand Caravan-Chrysler Town & Country; Driver Seat Side .... 1959 Chrysler New Yorker Bench Seat Rear Ash Tray.

You can make it release by pulling up on the metal bracket where the cable attaches under the seat at the back in the middle.

On my F150 (2002 model), there is only one release button. My daughter had removed the headrest, and put it on backwards. It was locked in place, so I couldn't get it off until I noticed a little pinhole on the opposite side of the side with the release button. I inserted a paperclip into the pinhole, and it released the locking mechanism on that side so that the headrest could pop right off.

The front bottom connections goes in first. You have to lift the back of the bench up and slide the u-shaped connections under the rods. Once there in, then lower the back of the bench. The back has latches that should spring open and around the rods in the floor opening. You should be able to actually drop the back of the bench and they should "seat", however it is better to place the back of the bench on top of the rods, and using the lever located on the bottom of the bench - open the latches; causing the latches to grab the rod.
Let me know if this helped, or if you have any additional information, problems, or questions. Feel free to contact me at FixYa.com!

You most certainly can!!!!

I did away with my 2nd row bench a long time ago.

The wreaking yard is the best place to find replacements, I even got a pair that matched. :)

On W-Body vehicles, the front seats are secured to the floorpan by two front hook attachments and two rear bolts installed to nuts welded to the floorpan.
The manually operated two-way front adjusters provides only fore and aft movement of the seat. When the seat adjuster handle located on the front seat is pulled up, the seat adjusters unlock, permitting travel of the seat. When the seat is in the desired position and the seat adjuster handle is released, the seat locks in place.
A power operated six-way seat adjuster is available. The adjusters are activated by three 12 volt, reversible, permanent magnet motors with a built-in circuit breaker. The motors are energized by a switch bolted on the seat side panel.
The three motors drive the front seat and rear vertical actuators and a horizontal actuator. When the adjusters reach the limit of travel, torque is absorbed through the rubber mounted grommets located between the motor and the support. An overload relay is provided in the circuit and will open should excessive stall be applied.
The optional 60/40 split bench front seats have seat back head restraints on the driver's and passenger's seat back. The head restraints are designed so they cannot be removed from the seat back without first inserting a small rounded tool inside the head restraint support tube to release the locking tab. The 60/40 split bench seat is equipped with a reclining mechanism on both the driver's and passenger's side. The recliner lever is located on the outboard side of the spring cushion. When the lever is pulled upward, the spring loaded dual linear reclining unit located in the cushion frame is released, allowing the seat back to be pushed rearward or allowing the spring loaded reclining unit to bring the seat back forward.
Bucket seats are equipped with manual reclining mechanisms. An optional six-way power seat adjuster is available. Some bucket seats are equipped with inertia seat back locks. This system allows the seat back to fold forward without requiring the occupant to release a locking lever or access to the rear seat area. During a sudden stop or deceleration, or if the front of the vehicle is nose down, the inertia system of the seat back lock will engage, holding the seat back in its rest position. A release lever is provided to allow manual release of the seat back lock when the vehicle is in the nose down position. The release lever is located at the lower rear outboard corner of the seat back.
Some W-Body vehicles (notably Pontiac coupes) have passenger front seats equipped with an E-Z Entry device. This is actuated, in an unoccupied seat, by completely folding the seat back forward disengaging the adjuster, and sliding the front seat forward to gain access to the rear seat area. To return the seat to its normal position, return the seat back to its rest position, and slide the entire seat rearward, engaging the adjuster.
W-Body rear seats are available in several styles including a rear seat with an integral child restraint device.

On the back side the the bench seat is a black level at the bottom. This lever lock the seat into place

I have a third row seat available from a 1995 Caravan. Contact, [email protected].

Yes...you can. I did this in my 05 Grand Caravan. We found ours at a local junk yard. It cost us 200 and even matched pretty well with the current benches. Just call around to your area junk/salvage people.

on my 2000 dodge grand caravan you can manually release the tailgate by manually lifting the connecting rod between the latch and the tailgate handle. you can access this rod by removing a small cover over an access hole near the latch at the bottom of the tailgate.