Which is 2014 Outback ignition switch and starter control fuse number and in which of the two panels is it located. Engine will not start.

Hello Michael Blell,

I went through all my favorite sources for repair information... with no luck

TYPICALLY BBB Industries has an excellent library of TECHNICAL SERVICE BULLETINS & wiring diagrams...
but when I pulled up 2014 I was surprised to see nothing for 2014

Try these sites below
(not even Haynes or Chilton gave any good clues).

Topic 2014 subaru outback 2 5i wiring diagram

http://www.agrozj.com/2014/2014-subaru-wiring-diagram

2014 Subaru Wiring Diagram

Before you do any thing check for loose or bad connections. Also check you ground connection to engine. Check Fuses, relay and for a Fusible Link open circuit. Now let me explain what a Fusible Link does. They are short lengths of small gauge wire installed between the Battery and the Ignition Switch, or the Battery and the Fuse Panel. They'll melt and open the circuit before damage occurs in the rest of the circuit. I hope this was helpful you.

( one question i have is every time the ignition fuse blows do i need to replace the starter relay? ) NO ! You have a dead short to ground on one of the circuits that fuse feeds. Do you know how to find a short circuit ? Video's on youtube show how. The fuse that blows ,is it IGN - A 40 amp. located in the under hood fuse/ relay center ? That fuse feeds B+ voltage to the ignition switch ,which powers up other thing's ,fuse's etc.. Not just the starter relay ! I see five other fuse's that get power from that fuse when ignition switch is in the start or run position . In the I/P fuse panel the gauges fuse #4 10amp , air bag fuse #10 10amp , turn b/u fuse #16 20amp. , Plus trans fuse #20 10 amp ! Pull out these fuse an try to start the van. if the ignition fuse doesn't blow the problem is in one of these other fuse circuits. There is one more fuse that get's B+ power from the ignition switch and ign A fuse ,crank fuse fuse #8 10amp. this powers the control side of the starter relay .
You can find a free wiring diagram here http://www.bbbind.com/free_tsb.html Enter vehicle info. year , make , model and engine . Under system click engine , under subsystem click starting. Click the search button then the blue link.
If you pull those fuse's i mention and it still blows the fuse look for a shorted ignition switch or wiring from ignition to the starter relay , not the relay itself. Park neutral safety switch . Isolate the circuit , pull the relay out of it's socket ,pull the crank fuse #8 in the I/P fuse box. with a ohm meter check to see if that part of the circuit is shorted to ground. Do you know how to do that ? Do you have a volt ohm meter ? You can buy one cheap at parts store .

check the starter and ignition fuse. starter fuse is located in the fuse box in your engine bay, ignition fuse is located in the kick panel which is right under your steering wheel.

the neutral switch is located in the left side of the transmission and its connected to the shift cable.

When you go to start the engine you are actually sending power from the ignition switch through a 20 amp fuse [crank fuse] then through the Park/Nuetral safety start switch and finally to the starter relay [located at the center rear of the engine compartment] This relay then sends a more powerful current flow down to the starter solenoid located on top of the the starter which then closes and allows full battery voltage from the large battery cable to energize and spin the starter. I don't think I've ever had to replace a starter relay on these but have replaced a large number of starters with bad solenoids and bad Park/nuetral switches. The "crank" fuse could also be bad but that is also pretty rare.

go to the link bleow and follow it to the Ford web site, there you can download a free owners manual, all fuse box info u need is in the manual.

http://www.edmunds.com/ownership/howto/articles/120189/article.html

relays are normally in the fuse panel on the left side of dash by knee.

Fuses and Circuit Breakers Location and Values
NOTE: The headlamp switch (11654) has an integral 20-amp circuit breaker.

• The combination instrument panel fuse and circuit breaker panel contains most of the fuses and circuit breakers used in the system.
• The fuses and circuit breakers are color-coded by amp rating.
• The locations and values of the fuses and circuit breakers not contained in the panels are shown in the following chart.

Circuit Circuit Protection and Rating Location Headlamps and High Beam Indicator 20 Amp. CB Integral with Lighting Switch Heated Back Window 16 GA Fuse Link Engine Compartment Power Windows, Power Seat, Power Door Locks 20 Amp. CB Starter Motor Relay Load Circuit Fuse Link In Harness Engine Compartment Lamp Fuse Link In Harness Convertible Top 25 Amp. CB Lower Instrument Panel-Reinforcement



Cavity Number Fuse Rating Color Circuit Protected A 40 Amp Orange

• Ignition Switch

B 40 Amp Orange

• Ignition Switch

C 40 Amp Orange

• Ignition Switch

D 50 Amp Red

• Headlamp Switch
• Instrument Panel Fuses 4, 8 and 16
• Instrument Panel Circuit Breaker 12

E 20 Amp Light Green

• PCM
• Fuel Pump
• HO2S (3.8L)
• Canister Purge Solenoid
• EVR Solenoid
• Ignition Control Module (3.8L)
• IAC Solenoid
• Fuel Injector
• Automatic Transmission
• Camshaft Position Sensor (3.8L)
• MAF Sensor

F 40 Amp Orange

• Heated Back Window

G 20 Amp Yellow

• Fuel Pump

H 60 Amp Blue

• Fan Control

J — — Not Used K 10 Amp Blue

• Anti-Lock Brake Control Module

L 20 Amp Red

• Fan Control Monitor (PCM)

M 25 Amp Yellow

• Horn
• Foglamps
• Daytime Running Lights Control Module

N 25 Amp Clear

• Fuses 5 and 9

P 20 Amp Clear

• Radio Amplifier

Q 20 Amp Yellow

• Generator

S 30 Amp Yellow

• Convertible Top Motor

T 60 Amp —

• ABS

2003 Excusion, V10, 2wd, Eddie Bauer

I had a hardtimefinding this informaton, hope it helps.

fuses
Fuse link
cartridge
2A Grey Grey — — —
3A Violet Violet — — —
4A Pink Pink — — —
5A Tan Tan — — —
7.5A Brown Brown — — —
10A Red Red — — —
15A Blue Blue — — —
20A Yellow Yellow Yellow Blue Blue
25A Natural Natural — — —
30A Green Green Green Pink Pink
40A — — Orange Green Green
50A — — Red Red Red
60A — — Blue — Yellow
70A — — Tan — Brown
80A — — Natural — Black
Passenger compartment fuse panel / power distribution box
The fuse panel is located below and to the left of the steering wheel by
the brake pedal. Remove the panel cover to access the fuses.
Roadside Emergencies
To remove the fuse panel cover,
turn the panel fasteners
counterclockwise.
To remove a fuse use the fuse puller
tool provided on the fuse panel
cover.

The fuses are coded as follows.
Roadside Emergencies
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse Panel
Description
1 15A* Adjustable pedals
2 20A* Power point -floor console
3 20A* Power point – 3rd row
4 20A* Power point -instrument panel
20A* Power point -right rear quarter
6 20A* Trailer tow turn/stop relay
7 30A* High beam headlamps / Flash to pass
8 — Not used
9 20A* Heated mirrors
10A* A/C clutch
11 20A* Radio (main)
12 20A* Cigar lighter / OBD II
13 5A* Power mirrors/switches
14 15A* Daytime running lamps
10A* Driver’s seat module memory
16 15A* Rear seat controller
17 15A* Exterior lamps
18 20A* Turn lamps/Brake on-off switch (high)
19 10A* Body security module/4x4 module
— Not used
21 25A* Rear wiper motor
22 20A* Engine control
23 20A* Engine control
24 15A* Air suspension
10A* 4-Wheel Anti-Lock Brake System
(4WABS) module
26 10A* Airbags
27 15A* Ignition switch Run feed
28 10A* EATC module module/Front blower relay
coil
29 10A* Customer access
Roadside Emergencies
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse Panel
Description
30 15A* Highbeam headlamps
31 15A* Clutch interlock switch
32 5A* Radio (start)
33 15A* Front wiper
34 10A* Brake on-off switch
35 10A* Instrument cluster
36 10A* PCM Keep-Alive
37 15A* Horn
38 20A* Trailer tow park lamps and backup lamps
39 — Not used
40 20A* Fuel pump
41 10A* Instrument cluster
42 15A* Delayed accessory
43 10A* Fog lamps
44 10A* PATS module, transceiver
45 10A* Ignition switch Run/ Start feed
46 10A* Left-hand lowbeam
47 10A* Right-hand lowbeam
48 10A* Rear wiper motor
101 30A** Trailer tow electric brake
102 30A** Door locks/Body security module
103 50A** Ignition switch
104 40A** Heated backlite
105 30A** Injector driver module
106 30A** Front wiper main
107 40A** Front blower motor
108 40A** Auxiliary blower motor
109 30A** Heated seats
110 50A** Ignition switch
111 30A** 4WD/Shift on the fly
112 30A** Left-hand power seats

Roadside Emergencies
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse Panel
Description
113 30A** Starter motor
114 30A** Right-hand power seats
115 20A** Trailer tow battery charge
116 30A** Ignition switch
601 30A CB Door window motors
602 60A** 4-Wheel Anti-Lock Brake System
(4WABS) module
210 — Not used
211 — Not used
212 — Not used
301 — Front blower motor relay
302 — Powertrain (EEC) relay
303 — Injector driver module relay (Diesel
only)
304 — Heated backlite relay
305 — Trailer tow battery charge relay
306 — Delayed accessory relay
307 — Starter relay
* Mini Fuses ** Maxi Fuses

i know this worked with my 99 navigator 32 valve used a viper car starter.

Lincoln

Navigator

1997-2003

Remote Starter Wiring Colors and Notes

Function
Vehicle Color
Location

Start:
RED/LT. BLUE
IGNITION SWITCH HARNESS **

Ignition #1:
D BLUE/GREEN
IGNITION SWITCH HARNESS

Ignition #2:
GRAY/YELLOW
IGNITION SWITCH HARNESS

Ignition #3:
RED/BLACK
IGNITION SWITCH HARNESS***

Accessory:
BLACK/LT. GREEN
IGNITION SWITCH HARNESS

Brake Light:
L GREEN (+)
AT SWITCH ABOVE BRAKE PEDAL

Tach Signal:
WHITE/PINK
AT POWERTRAIN CONTROL MODULE *

Parking Lights:
BROWN (+)
AT HEADLIGHT SWITCH

Headlights:
RED/YELLOW (+)
AT HEADLIGHT SWITCH

OEM Alarm Disarm:
D GREEN/PURPLE (-)
DRIVER KICK PANEL

OEM Alarm Arm:
N/A


Diesel Glow Plug:



Clutch Bypass Wire:



Notes:
* Powertrain Control Module (PCM) Located On Passenger Side Of Engine Compartment On Passenger Wheelwell. This Wire Can Also Be Found At the Firewall Harness On the Driver's Side of Vehicle. ** This Vehicle Is Equipped With Ford's PATS Anti-Theft System. Use Universal Alarm Bypass Module part # 2x402 where X can be any number. *** Must power ign3 using a relay. Tap relay coil to ign3 connection of remote start along with bypass module. No diode isolation is required.