Where is the power door locks relay for a 1995 Pontiac Bonneville with keyless entry

Do they work with the key fob, do you have one of those? They lock when put into gear an unlock when put into park because the BCM - body control module does that .

Door Lock System Components
The power door lock system consists of the following components:
• Driver door lock switch
• Front Passenger door lock switch
• Body Control Module (BCM)
• Relays: Driver Door Unlock -- on vehicles with RFA, Door Unlock, and Door Lock
• Door Lock fuse 15A
Door Lock System Controls
The power door lock system can be controlled by any of the following:
• A power door lock switch activation
• A keyless entry command -- if equipped with keyless entry


Driver and Passenger Door Lock Operation
When any of the door lock switches is pressed to the lock position, the BCM door lock/unlock signal circuit changes from an idle voltage of ~3.4 volts to 0.0 volts generating a lock command. The BCM then applies battery positive voltage to the Door Lock Relay, which in turn applies battery positive voltage to the Door Lock Actuator lock circuit of all the Door Lock Actuators. Since the Door Lock Actuator unlock circuits are held to ground through the resting Door Unlock Relay(s), the actuators execute the lock command, locking the doors.
The lock function can also be accomplished by the BCM having received a keyless entry door lock command, if the vehicle is equipped with keyless entry.


Driver and Passenger Door Unlock Operation

When any of the door lock switches is pressed to the unlock position, the BCM door lock/unlock signal circuit changes from an idle voltage of ~3.4 volts to ~1.7 volts generating an unlock command. The BCM then applies battery positive voltage to the Door Unlock Relay and the Driver Door Unlock Relay when equipped with keyless entry, the relay(s) in turn apply battery positive voltage to the Door Lock Actuator unlock circuit of all the Door Lock Actuators. Since the Door Lock Actuator lock circuits are held to ground through the resting Door Lock Relay, the actuators execute the unlock command, unlocking the doors.
The unlock function can also be accomplished by the BCM having received a keyless entry door unlock command, if the vehicle is equipped with keyless entry. Keyless entry personalization allows the driver door to be unlocked individually before unlocking the passenger doors. When this feature is active, the BCM will require a repeated unlock command to unlock the passenger doors.


Automatic Door Lock/Unlock
The automatic door lock/unlock function is a Vehicle Personalization feature with the following four programmable modes of operation:
The automatic door lock feature is disabled.
All of the doors lock when the vehicle is shifted out of Park with the ignition ON.
All of the doors lock when the vehicle is shifted out of Park with the ignition ON, and all of the doors Unlock when the vehicle is shifted into Park.
All of the doors lock when the vehicle is shifted out of Park with the ignition ON, and only the driver door Unlocks when the vehicle is shifted into Park.
For information on programming the automatic door locks, refer to Vehicle Personalization in Personalization.

Time for a new key fob ? Does it work good for locking the doors ?
Module Controlled Functions The multifunction modules consist of the following:

• generic electronic module (GEM)/central timer module (CTM)
• remote anti-theft personality (RAP) module (15K602)

The remote anti-theft personality (RAP) module controls the keyless entry, and computer operated locks systems.
The GEM/CTM controls the following features:

• wiper/washer (front/rear)
• warning chime
• battery saver
• illuminated entry and courtesy lamps
• driver one touch down power window (GEM only)
• accessory delay
• 4 wheel drive (GEM only)
• For keyless entry concerns, refer to Section 501-14B .
• Keyless Entry The keyless entry system components consist of the following:
  
  • keyless entry remote transmitter (15K601)
  • remote anti-theft personality (RAP) module (15K602)
  • driver unlock relay (if equipped with two step unlocking)
  • all unlock relay
  • all lock relay
  • keyless entry keypad (14A626)
  The electronic door lock system has three main components: the remote anti-theft personality (RAP) module, attached to the rear left hand quarter panel, the three-button (hand held) keyless entry remote transmitter (15K601), and the keyless entry keypad (14A626) on the driver side door.
  The door locks are controlled by the RAP module through three external relays: the driver unlock relay (if equipped with two step unlocking), the all unlock relay, and the all lock relay. These relays are located in the relay box on the LH rear quarter panel.
  The keyless entry remote transmitter initiates the following electronic door lock system functions:
  
  • Unlocks the driver door (if equipped with two step unlocking).
  • Unlocks all doors.
  • Locks all doors.
  • Enables the panic alarm.
  • Issues the interior lamps on (when unlocking) and off (when locking) commands to the generic electronic module (GEM).
  • Sounds the horn (13832) once when LOCK on keyless entry remote transmitter is pressed twice, and doors are closed.
  • Sounds the horn twice when LOCK on the keyless entry remote transmitter is pressed twice, and any door or the liftgate window is ajar.
  • Allows up to four keyless entry remote transmitters to be programmed.
  • The order that the transmitters are programmed into the module will set the memory seat to the corresponding position when the driver door is unlocked with the transmitter.
  NOTE: The remote entry features will not function when the ignition switch (11572) is in the RUN or ACC position.
  The keyless entry remote transmitters are reprogrammable and must be set at the same time.
  To confirm that the doors have been locked and that the anti-theft system has armed, press the LOCK button again, within five seconds of the first press. The horn will sound once if the doors have locked and all doors are closed.
  
• Inspection and Verification
  
  1. Verify the customer concern by operating the electronic door lock control system.
  1. Visually inspect for obvious signs of mechanical and electrical damage; refer to the following chart:
     
     Visual Inspection Chart Mechanical Electrical
     • Binding latches
     • Fuse(s) 20 (7.5A), 9 (20A), 18 (10A), 1 (60A), and 25 (7.5A)
     • Relays
     • Wiring harness
     • Loose or corroded connections
     • Keyless entry keypad
     • Remote transmitter
     • Door open warning lamp switch
  1. If the concern remains after the inspection, connect the scan tool to the data link connector (DLC) located beneath the instrument panel and select the vehicle to be tested from the scan tool menu. If scan tool does not communicate with the vehicle:
     • check that the program card is properly installed.
     • check the connections to the vehicle.
     • check the ignition switch position.
  1. If scan tool still does not communicate with the vehicle, refer to the scan tool manual.
  1. Perform the DATA LINK DIAGNOSTIC TEST. If the scan tool responds with:
     • CKT914, CKT915 or CKT70 = ALL ECUS NO RESP/NOT EQUIP, refer to Section 418-00 .
     • NO RESP/NOT EQUIP for RAP, go to Pinpoint Test A.
     • NO RESP/NOT EQUIP for GEM/CTM, go to Pinpoint Test G.
     • SYSTEM PASSED, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs and perform self-test diagnostics for the RAP.
  1. If the DTCs retrieved are related to the concern, go to RAP Diagnostic Trouble Code (DTC) Index or GEM/CTM Diagnostic Trouble Code (DTC) Index to continue diagnostics.
  1. If no DTCs related to the concern are retrieved, proceed to Symptom Chart to continue diagnostics. Taking your vehicle to a qualified repair shop mite be your best bet , one that has a scanner that can read these code
  2. RAP Module Diagnostic Trouble Code (DTC) Index
     RAP Module Diagnostic Trouble Code (DTC) Index DTC Description DTC Caused By Action B1309 Power Door Lock Circuit Short to Ground RAP GO to Pinpoint Test C . B1341 Power Door Unlock Circuit Short to Ground RAP GO to Pinpoint Test C . B1485 Brake Pedal Input Circuit Short to Battery RAP GO to Pinpoint Test D . B1526 Keyless Entry Keypad Switch Circuit Short to Ground RAP GO to Pinpoint Test B . B1629 PRNDL Reverse Input Short to Battery RAP GO to Pinpoint Test E . B1845 Ignition Tamper Circuit Failure RAP Invalid DTC. Ignore this DTC. B2425 Keyless Entry Out of Synchronization RAP GO to Pinpoint Test C . B1334 Decklid Ajar Rear Door Circuit Short to Ground RAP REFER to Section 417-02 .

The Lock's lock from the door switches ? If they do it's not a fuse problem . Which of these does your vehicle have ?
Keyless Entry System Description and Operation (with Accessory 2 Way Remote)
Keyless Entry System Description and Operation (without Accessory 2 Way remote)

The keyless entry system is a vehicle entry device. The keyless entry system is used in conjunction with the body control module (BCM) to remotely activate certain vehicle features. Keyless entry will lock/unlock the doors/liftgate when a corresponding button on the keyless entry transmitter is pressed. This is accomplished by the transmitter sending a radio frequency to the remote control door lock receiver (RCDLR). The RCDLR interprets the signal and activates the requested function via a serial data message to the BCM. A low transmitter or vehicle battery or radio frequency (RF) interference from aftermarket devices, such as 2-way radios, power inverters, computers, etc., may cause a system malfunction. High RF traffic areas may also cause interference that could lead to a malfunction. Keyless entry allows you to operate the following components:
• Door locks
• Liftgate lock
• Vehicle locator/Panic alarm
• Illuminated entry lamps
• Remote vehicle start
The keyless entry system has the following components:
• Keyless entry transmitters
• Keyless entry antenna
• 2 Way Advanced Remote Start RCDLR
• BCM

Your best bet , take it to a GM dealer .

This may be a bad rear integrated control module. or connection or wiring to it.
REAR INTEGRATION MODULE (RIM)
The CTD system is an internal function of the rear integration module (RIM) which utilizes class 2 serial data and various switch input information to perform CTD functions. When the RIM detects an unauthorized entry, the RIM sends a message via the serial data circuit to the DIM to activate the horns and exterior lamps. The RIM has 5 basic modes. Disarmed, standby, delayed, armed, and alarm for operating the CTD system. The 5 modes transition from one step to the next in the following order:

When in the disarmed mode, ignition is OFF and any door is open the RIM commands the instrument cluster to flash the SECURITY indicator via the class 2 serial data circuit. The RIM has the CTD system in a disarmed mode until the following conditions are detected:

Ignition key turned to the OFF position
Any door open
Doors locked by either the power door lock switch or the LOCK button on the keyless entry transmitter

The RIM enters the standby mode when the above conditions are detected. In standby mode the RIM commands the instrument cluster to illuminate the SECURITY indicator via the class 2 serial data circuit. If all the doors are closed and the LOCK button on the keyless entry transmitter is used, the RIM enters the delayed mode.
When the last door is closed, the RIM enters the delayed mode for 30 seconds . In delayed mode the RIM commands the instrument cluster to illuminate the SECURITY indicator on steady via the class 2 serial data circuit.
After 30 seconds , the RIM enters the armed mode. In armed mode the RIM commands the instrument cluster to turn off the SECURITY indicator via the class 2 serial data circuit. Any forced entry activates the alarm mode.

.

Viper Keyless Entry Systems

https://www.viper.com/car/keylessentry/

Viper is the industry leader in keyless entry systems. Add the convenience of keylessentry to virtually any vehicle - even vehicles without power door locks!

Alarms, Remote Car Starters, Keyless Entry & Locks - JC ...

www.jcwhitney.com > Audio, Video & Electronics

20 out of 32 products in Alarms, Remote Car Starters, Keyless Entry & Locks ..... ofKeyless Entry & Car Alarms allow you to lock and unlock power door locks.
How to program your keyless entry keypad - Ford Ownerhttps://owner.ford.com/.../locks.../how-to-program...Ford Motor CompanyDiscover how to lock and unlock your doors and how to program memory settings that will adjust seats & mirrors for each driver.SecuriCode™ Keyless Entry Keypad - Ford Ownerowner.ford.com/.../locks.../securicode-keyless-entr...Ford Motor CompanyLearn how to set a 5 digit SecuriCode on the Ford keyless entry keypad. ... Sign out. Register/Sign In · Your Vehicle. Service & Maintenance. Service & .... vehicle's SecuriCode keypad to lock and unlock your doors without having to use a key. ... Thekeypad will go into an anti-scan mode if you enter the wrong code seven ...How Programming Your Keyless Entry Can Make ... - Ford Life

The keyless entry system is controlled by the (GEM) - generic electronic module .
Keyless Entry The electronic door lock system has two main components:

• generic electronic module (GEM)(14B204)
• keyless entry remote transmitter (15K601)
• NOTE: Battery power and ground must be remove before disconnecting the GEM connectors to avoid setting false codes.
  Power Locks Operation The power locks feature allows the customer to lock and unlock the doors via momentary switches located on the driver and passenger door. When the GEM detects a momentary press of the driver or passenger lock button, the GEM will supply power to the driver or passenger lock actuators for approximately 250 ms from relays internal to the GEM. When the GEM detects a momentary press of the driver or passenger unlock button, the GEM will supply power to the driver or passenger unlock actuators for approximately 250 ms from relays internal to the GEM.
  Remote Keyless Entry Door Locks Operation The remote entry feature allows the customer to unlock the driver door, unlock all doors, and lock all doors using a valid remote transmitter as long as the ignition switch is not in RUN or START. The driver door is unlocked whenever the GEM detects a valid remote transmitter unlock transmission. All the doors are unlocked when the GEM detects a second valid remote transmitter unlock transmission within three seconds of the first transmission. All the doors are locked when the GEM detects a valid remote transmitter lock transmission. If the GEM detects a second valid remote transmitter lock transmission within three seconds of the first transmission, the doors will lock again, the horn will sound for 20 ms and the parking lamps will flash for 200 ms to indicate the doors are locked. If the GEM detects the driver or passenger door is ajar during the second lock transmission, the doors are locked again and the horn is sounded twice. If the GEM detects a valid remote transmitter lock transmission within three seconds of detecting a valid remote transmitter unlock transmission, the GEM will lock all the doors
• • The doors do not lock/unlock using the remote transmitter
  • Ignition switch.
  • GEM.
  • Remote transmitter.
  • Remote transmitter batteries.
  • GO to Pinpoint Test C .
  You followed the program instructions to the letter ? Programming -Keyless Entry Remote Transmitter NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
  NOTE: All previous transmitter identification codes (TIC's) will be erased when programming mode is entered.
  NOTE: To program (or reprogram) the keyless entry remote transmitters into the generic electronic module (GEM)(14B204), perform the following steps.
  
  1. Turn the ignition from OFF to RUN eight times within 10 seconds, ending in RUN. If the GEM has successfully entered program mode, it will lock and unlock all the doors.
  1. NOTE: The first TIC must be entered within 7.5 seconds of entering the program mode and additional TICs must be entered within 7.5 seconds of the first TIC. The programming mode is exited whenever the timing constraints are not met.
     Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait for several seconds and press the button again.
  1. Turn the ignition switch to the OFF position, or wait up to five minutes after step 1, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the GEM will lock and unlock all the doors one last time.
  1. Take an have the vehicle checked for DTC'S

B1396 Power Door Lock Circuit Short to Battery GEM GO to Pinpoint Test B . B1397 Power Door Unlock Circuit Short to Battery GEM

all these functions go through the anti-theft module, replace it.

Double press and hold the entry button to reset all doors to open. The key fob as set itself to driver door only by the sounds of it.
Take the battery out and leave a few minutes, then insert and pair. ( driver door open )

To activate the autolock feature, use the following steps:

1. Enter the five-digit permanent entry code into keyless entry keypad (14A626) .

1. Press and hold the 7/8 button on the keyless entry keypad within five seconds of entering the code.

1. Press and then release the 3/4 button within five seconds of pressing and holding the 7/8 button.

1. Release the 7/8 button on keyless entry keypad within five seconds of releasing the 3/4 button. To deactivate the autolock, repeat the above sequence.
   

95 bonny--1-turn ign switch off 2-using a fused jumper wire jumper data link connector #8 blk/wht wire to #4 blk wire (look under dash for dlc)
3-press unlock button on 1 transmitter doors should lock and unlock
4-repeat step 3 if doing more than 1 remote
5-remove fused jumper

for the 1993 car same way except jumper term a blk/wht
term g ppl/wht
have fun