2001 Saturn l200 what tools need to remove - 2001 Saturn L-Series

SOURCE: I am getting poor gas milage on my 2001 saturn

These are the most common causes for bad mileage.
Tire pressure is a huge factor (Tire should be set at the factory recommendation or 1-2 psi above, but never below - Tire should also be a Low Rolling Resistance Tire)
Oil level (you said it's OK, so I assume it's not above the full mark)
Running extra accessories (A/C, etc)
Dirty Air Filter
bad Ignition timing
engine running hotter than normal
fuel injectors may be stuck partially open
bad fuel pressure regulator
faulty emission control device (this usually triggers a check engine light)

SOURCE: Where is the fuel pump located on a 2001 Saturn

you have to remove the gas tank you have to remove the exhaust pipes to get to the gas tank the best way to get to it is to put the car on a lift once you remove the tank you will see it on top it is one piece connected to the fuel gauge and the entire thing is inserted on the top side it is hard to get to because there is no access panel under the back seat like in japanese cars it is a pretty costly item too, good luck

SOURCE: how to replac timing chain on 2001 saturn L200

timing a 2001 saturn engine l 100

SOURCE: what is the spark plug

Sir, The gap is0.045 in this info is for the2.2 L4 engine. The Saturn part number for the plugs is25325361.

Duane Wong

• 6826 Answers
• Posted on Jan 29, 2011

SOURCE: I need to replace the fuel pump on my 2001 Saturn

Fuel Pump REMOVAL & INSTALLATION 1.9L Engine To prevent excessive fuel spillage, whenever the tank is removed from the vehicle it should be no more than 1?2 full. Removal of the fuel pump module assembly requires the removal of the fuel tank.

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Properly relieve the fuel system pressure.
3. Remove or disconnect the following:
   • Negative battery cable
   • Fuel feed and return lines from the filter/pressure regulator
   • Fuel pump vapor line from the fuel tank vent pipe
   • Fuel pump module retaining ring with service tool SA9156E. A 1?2 inch breaker bar will loosen the lockring
   NOTE: To prevent bending of the sending unit float arm, lift the pump module up slightly to disengage the orientation tabs in the tank. Rotate the module 90 degrees clockwise until the fuel lines are facing the 1 o'clock position.
   • Fuel pump module from the fuel tank until the bottom of the pump module is close to the fuel tank opening
   • Tilt the pump module approximately 45 degrees to the right hand side of the tank and lift the pump from the fuel tank
   • Fuel pump to tank seal and discard it
   To install:
   
4. Install or connect the following:
   • Fuel pump module into the fuel tank by orientating the float to face the right side and tilting the module approximately 45 degrees
   • Fuel pump into the tank and rotate the assembly 90 degrees counterclockwise to align the module tabs with the slots in the tank
   NOTE: The fuel pump retaining ring cannot be properly installed if the flange locator tabs are not aligned with the slots in the fuel tank.
   • Retaining lockring with tool SA9156E
   • Vapor line to the fuel tank vent pipe
   • Fuel feed and return lines to the filter/pressure regulator
   • Fuel feed, return and EVAP canister purge line in the fuel tank retaining clip
   • Fuel tank
   • Negative battery cable
5. Start the vehicle and check for leaks, repair if necessary.

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Properly relieve the fuel system pressure.
3. Remove or disconnect the following:
   • Negative battery cable
   • Fuel tank
   • Fuel lines from the fuel pump module cover
   • Fuel pump module retaining ring with a Sending Unit Wrench, J43827
   • Pull the retaining clip toward the float arm and lift up
   • Fuel pump straight up from the fuel tank
   • Fuel pump tank seal and discard the seal
   • Fuel feed line from the bottom of the fuel pump cover with Clamp Pliers J43914
   • Fuel pump electrical connector Fig. 1: Remove the fuel pump cover lockring-2.2L and 3.0L engines
     
   To install:
   
4. Install or connect the following:
   • Fuel pump feed line to the cover
   • Fuel pump electrical connector
   • Fuel pump to the new seal
   • Fuel pump cover lockring with tool J-43827
   • Fuel lines and wiring harness
   • Fuel tank
   • Negative battery cable
5. Start the vehicle and check for leaks, repair if necessary.