Question about 2000 Land Rover Discovery
Trying to jumpstart a dead battery on a 2000 range rover but each time I connect jumper cables alarm goes off and wont allow me to jump start. I dont have a remote to shut it off. how do I overide alarm so I could jumpstart
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
This car is in super lock mode... when you press remote 2times to lock or when you lock with remote and try to unlock using key manually.
there is a 4 digit number to open the door, its like opening a safe, starting from the left(key in car door) it goes L/R/L/R. so if number code is 1234..... left 1, right 2, left 3, right 4.
or if this too troublesome you can ask landrover dealer to remove the KEYCODE.
Posted on Jan 19, 2009
SOURCE: My P38 Range Rover wont start
Bring your vehicle to an auto parts or battery store. Ask if they could perform a 'Load Check' on your battery. This not only checks the voltage, but also the amps, as if it were under the load of turning your engine.
It takes a few seconds and the results are pass or fail. Fail means it's time for a new battery. Pass means we need to look elsewhere.
Comment back the results.
Hope you find this to be very helpful
Posted on Sep 21, 2009
Unfortunately, there is a trick to replacing the battery.
1) Open the Driver side door.
2) Open the Bonnet and take the battery cover off.
3) Use your remote to lock and unlock the car (keeping the driver side door open)
4) Pull the Negative Lead from the battery first, followed by the Positive Lead.
5) Change or replace with charged battery.
6) Closed down Bonnet.
7) Your windows, sunroof, and key FOB will not work... so follow the next steps.
7a) Insert your key, with door closed into the exterior lock on driver's side.
7b) While turning the key to lock the door, hold down the "lock" button on your remote for 5 seconds while in "lick" position
7c) Your remote will reset, and you should be able to use your remote now
7d) While driving, roll each window down twice. On your third attempt, you should only have to touch the window button, and the window will have reset
Enjoy your Rover!
Posted on Jul 04, 2010
There are few possibilities that are to be checked.:----
Engine cranks normally, but it does not fire: If you know that you have spark and fuel, the next step is to check for compression. For this, you will need a mechanic's grade compression tester that will screw into a spark plug hole. You will need to remove the spark plugs and use the compression tester to test the compression on each cylinder. If the compression is very low on all cylinders, that is a sure sign that the timing belt (or timing chain depending on the engine) has failed and will have to be replaced. ------------- This troubleshooting will let you know the problem.Thanks.
You turn the key to start and hear the starter motor crank the engine, but when you release the key, the cranking stops and there is silence. This means that the battery and starting motor are working properly, but the engine is not firing. If you continue cranking the engine over in this way, the battery will eventually run down and will need to be recharged, but the battery and starter are not the cause of your problem.
There are a number of causes for this type of no-start condition, the most common being that you are simply out of gas. Assuming that you have fuel in the tank, you will need to go through a series of tests to determine what is causing the problem. The testing procedure is as follows:--- Spark:---------An easy way to test for spark is with an inexpensive spark tester. This is a device that is readily available at most auto supply stores. You use it by simply holding it next to a spark plug wire. If you see the neon lamp flashing while someone cranks the engine, then you have spark and should move on to checking for fuel. If there is no spark, or a very weak spark, you will have to replace the spark plug or the coil pack.It has to be checked. Fuel:
First step here is to listen for the fuel pump running inside the gas tank. When you turn the key to run, you should easily hear the pump come on, run for a few seconds to build fuel pressure, then turn off. If you do not hear it, it could mean that the fuel pump or circuitry is bad. (Fuel pump failure is a common problem). Fuel injected cars are very sensitive to proper fuel pressure. If the pressure is off, even by a few pounds, it will cause noticeable performance problems, or a no-start condition. To check for proper fuel pressure, you will need a fuel pressure gauge that is suitable for your type of system.Or you can also get the fuel pressure tested at local car garage,If fuel pressure is low then its a fuel pump and fuel filter related problem. Compression:
If you know that you have spark and fuel, the next step is to check for compression. For this, you will need a mechanic's grade compression tester that will screw into a spark plug hole. You will need to remove the spark plugs and use the compression tester to test the compression on each cylinder. If the compression is very low on all cylinders, that is a sure sign that the timing belt (or timing chain depending on the engine) has failed and will have to be replaced.
This troubleshooting will let you know the problem.Thanks.
Posted on Dec 08, 2010
Testimonial: "Thank you very much for such a quick and detailed response. I will try your suggestions and see how I get on. Thanks again."
Tips for a great answer:
Mar 02, 2015 | 2000 Ford Windstar
May 14, 2014 | 1988 Cadillac Eldorado
Mar 01, 2011 | 1991 Honda Accord
Jul 06, 2010 | Mercedes-Benz C230 Cars & Trucks
Oct 28, 2009 | 2006 Kia Sedona
Oct 03, 2009 | 1993 Chevrolet K1500
Mar 25, 2009 | 1995 Plymouth Grand Voyager
Jan 04, 2009 | 1992 Saab 9000
Dec 10, 2008 | 1993 Mitsubishi Galant
58 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: