Help size of serpentine on a cherokee 93 with the intake and power steering pump of a 2000 original 5060975 to long bought good year 4060922 to short by like 3 to 4 inches any one knows the size to use

That is strange because they are unrelated.

The power steering works using a pump that has a pulley and is turned by the Serpentine belt. Where you put the fluid, did it look like this?

https://www.carparts.com/power-steering-pump/jeep/grand-cherokee/2003

https://www.google.com/search?q=2003+jeep+grand+cherokee+power+steering+pump

The Brake Master Cylinder has a similar reservoir and also has a brake booster that uses vacuum power from the engine to give you a mechanical advantage. Both are shown here

https://www.ebay.com/b/Brake-Master-Cylinders-Parts-for-Jeep-Grand-Cherokee-for-2003/33566/bn_87327012

..

An auto parts supplier can advise you.

You can, t bypass power steering you will never control the car , just by a new or second hand pump.

Make sure the serpentine belt is tight. If it is you may have gotten a bad pump

Below is the master help link provided to go through belt routing diagram:---Timing belt, drive belt, serpentine belt, accessory belt, fan belt, engine belt routing diagrams for all types of car models?
Click the link below: ----

http://carbeltrouting.blogspot.in/2012/02/timing-beltdrive-beltserpentine.html
----------This will help. Thanks.

Click of the following direct, Free Link. It has several Serpentine Diagrams, including the one for your 1989 Jeep Cherokee 4.0L In-Line 6-Cylinders based upon your Engine Options (AC/No AC, Power Steering/No Power Steering, etc.). The Link Page ALSO has the 2.5L In-Line 4-Cylinder Serpentine Belt Diagrams with their various engine options.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1989/make/jeep/model/cherokee/1989_jeep_cherokee_drive_belt_routing_diagram.htm

are you sure those intakes are inter changeable?
if you still have the 98 intake and your 93 block ,sit there and look for any differences in holes or hole locations.
another way to check is when it is running remove the oil fill cap and see if it stalls or picks up speed.

For the 1991 DODGE DYNASTY - V6 3.3L 201ci GAS FI N R , review this informacion:

Belt Routing Diagram
- Multiple Accessory, w/o A.C. (Mfg. After 2/27/91)
- Multiple Accessory, w/A.C. (Mfg. After 2/27/91)
- Multiple Accessory, w/o A.C. (Mfg. Before 2/27/91)
- Multiple Accessory, w/A.C. (Mfg. Before 2/27/91)



Remove the serpentine belt by using a breakover bar, rachet or serpentine belt removal tool with the correct size socket for the pulley mounting bolt. Rotate tensioner arm to release tension. Remove the belt.

Hope helped with this (remember rated this help) Good luck.

Around the outside of power steering pulley,under idler,over a/c comp,around alternator,over fan pulley, around crank pulley, over water pump. The backside of the belt contacts the idler, fan and water pump.

You can bypass both the AC compressor and the middle serpentine idler pulley with a 6PK1790. The middle pulley is bypassed by running the belt straight line from the upper rear serpentine idler straight to the power steering pulley, then over the water pump (the smooth pulley powered by the back side of the belt) and down to the engine drive pulley (harmonic balancer), bypassing the AC compressor) This works fine. On 9.5 models, the same basic idea, but a slightly different sized belt.