Van wont start, and i replace the starter. you can hear the fuel pump when you turn the key, and it has sparks

im going to say the starter is shot

If the Starter isn't turning the engine over, but you hear a clicking sound, you may have a bad Starter.
If the Starter is turning the engine over, but you are getting no Spark, you may have a failed Camshaft or Crankshaft Position Sensor, or your Timing Belt may have jumped or broken(common on the neons).
If the Starter is turning the engine over, but you are getting Spark, you may have a failed fuel pump, fuel pump relay, or fuel pressure regulator.

Before you start replacing sensor, double check the Timing belt to ensure it hasn't broken or jumped, and check to see if you are getting a spark or not.

I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

You say its not the not the starter,alterrnater or Battery. What do you have to base this on?
What happens when you turn the key?
How much fuel do you have?
Do you have an imobiliser?

remove starter and have it tested at your local part store

need to narrow the field a little,1st check battery connections,turn headlights on @ turn key to start, if lights dim,,starter drawing amps,could be bad starter, is fuel pump humming when key on? if not check fuses under hood for fuel pump relay if ticks when key turned on it's good. it's either a spark or fuel issue, hope this helps!!

Start with fuel system. Listen for fuel pump humm at fuel tank No humm check wiring to pump for power. Then check for spark at plugs and wires. Remove wire from coil and hold near engine and see arch when you crank. No arch. Replace ignition Modular inside distributor cap or cap or rotor

you need to have some to stand back by the side of the van while you turn the key to listen if you can hear the fuel pump if not check out the fuel pump really first before replacing the fuel pump if its in the tank give these websites a try www.alldatadiy.com and www.autozone.com.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your van wish you the best Michigan Man.

after you put gas in it did you prime the system?

when the gas runs out it drains the fuel lines, so after you put gas in the tank you will need to prime the system. To do this turn the key on to run but don't crank the starter and count to three, then key off and out. Do that three to four times and that should take care of getting gas to the engine.

Make sure you can hear the fuel pump turn on when you turn the key on. Sometimes when you run low on gas it can overheat the fuel pump causing it to fail.

Check to see if the fuel pump is kicking in,
when you turn the key on without starting the van you should hear it kick on for about 2 seconds,

It could be...
A clogged fuel filter...
Blown fuse for the pump..or bad pump relay..
No gas
Bad fuel pump

if the starter is revving very slowly it is the battery, charge battery. if not, It can be three things happing. 1 no spark 2 no fuel 3 no crank signal or the car computer is bad- you will need to unplug one of the spark wires and remove the spark plug and put the spark plug in the spark plug wire boot, and touch the spark plug on any metal on the car and have some start the car. donot touch the spark plug itself and see if there is a spark. if spark is bright, then it is not spark plug and wires but if no or spark is not bright, check the spark plug wires by applying a little bit of water on the spark plug wire and take a 12v test light, connect the clap to ground and and have some one to crank the vehicle, touch allover the spark plug wires with the tip of the test light, if you see spark, replace the wires and change the plugs.. they are not good. if spark is present, check for fuel by removing any one of the spark plugs and see if it is wet. if wet fuel pump is ok but if not go look for the fuel pump fuse and relay. is fuse blown, replace, check the relay resistor with a volt meter. it should be around 40 to 80 ohm. if everything is good from this point check the fuel pump itself by disconnecting the connector to the pump and apply 12v and ground using jumper wires or some wires to the fuel pump if you donot hear the pump,replace pump. if you, the crank signal or computer may be the problem