Question about 2011 Chrysler 200

1 Answer

Low beam headlight adjustment on 2011 Chrysler 200

Need help to adjust low beam illumniation on 2011 Chrysler 200

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 182 Answers

How to Adjust Car Headlights Level your car. Start by removing any excess weight from the trunk of the car. Also, ensure that the tire pressure in all tires is at the manufacturer's recommended levels. If possible, have somebody sit in the driver's seat, and that the gas tank is half-full. As well as this, check that your headlight aim adjustment wheel (if fitted) is at the zero position. Position your car. On level ground, park 10 to 15 feet (3.0 to 4.6 m) from a dark wall or garage door, with the front of the car aimed at the wall. A paved parking lot or level driveway is best Turn the headlights on. Do not use your high beams or fog lights. Mark the horizontal and vertical center lines of the headlight beams with masking tape to make two T's on the wall or garage door.Make sure the lights are level. Place a carpenter's level between the two marked center lines to see if they are even. If they are not even, use a tape measure to measure how far up the wall the lower mark is and lower the other center line marker to the same height. These center lines should be no higher than 3.5 feet (1.1 m) from the ground.Back your car exactly 25 feet (7.6 m) from the wall or garage door. Don't estimate the distance! Use a tape measure to make sure you are the proper distance away from the wall. Turn off the headlights. Remove the trim ring from around the headlights and locate the adjusting screws. These screws are typically found adjacent to the headlight, though some manufacturers put the screws in the engine compartment, behind the the headlights. The horizontal adjuster and the vertical adjuster should be marked.

  • Always defer to the specs in the owner's manual-Adjust each headlight separately. Block one with a sweatshirt or other object while adjusting and testing the other, since the light-bleed can make it difficult to distinguish one from the other. Have a helper sit in the driver's seat while you do the adjustments, to turn the lights on and off while you make the proper adjustments

Posted on Sep 30, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I adjust the passenger side low beam headlight on a 2011 Mazda cx 7


here's your answer for the low beam..

https://www.justanswer.com/mazda/58sx8-mazda-adjust-headlights-low-beam-needs-higher.html
just make sure to have the vehicle somewhere where the headlights reflect off wall/garage door with the vehicle about 15-20 feet away so you don't go too high if that's the direction you want to go. and end up blinding oncoming traffic.
hope this helps you.

Feb 04, 2018 | Mazda Cars & Trucks

1 Answer

07 Chrysler 200 low beam headlights won't come but high beams and fog lights work just fine. Please Help!


your headlights are most likely the halogen type, when these headlights burnt out, it is almost always the dims that go first, then the high beams. replace.

May 23, 2017 | Chrysler Cars & Trucks

1 Answer

Low beam headlight illumination


I would first replace the bulbs and have them adjusted.

Sep 30, 2016 | 2011 Chrysler 200

2 Answers

Driver side headlight goes dim on high beam while passenger side is bright


bad connection or bad earth check all connection or bulb

Jan 24, 2016 | Cars & Trucks

3 Answers

How to adjust halogen headlights (too low now)


there example of how to do it i would been more acurate but you didnot mention the year make and model hope it help you

Apr 08, 2015 | Cars & Trucks

1 Answer

I have a 2003 kia spectra. Can the headlights be adjusted. On low and high beams they seem to be set to low. I feel they should shine out futher to be able to see more while driving at night


the headlights can be adjusted but you can't adjust the high & low beam separately, you can only adjust the light as a unit unless you have a separate high & low beam lights ( twin lights) ......hope this helps......cheers.

Sep 05, 2011 | 2003 Kia Spectra

1 Answer

I need to replace and then adjust the headlights on my 2000 Chrysler 300M. How do I replace the headlights, then adjust them.


Park your vehicle on level ground with the headlights near a garage door or wall. A good distance is 2-3 feet away from the wall or door. The location must be perfectly level and flat at a distance of 10 to 25 feet away from the door or wall.
Switch on the low headlight beams and mark the horizontal and vertical centerlines of each headlight beams on the wall using masking tape. This will mark the center of each beam with a +. The marking will tell you where exactly the headlight beams should be centered from a distance.

Move the vehicle back about 10 to 25 feet away from the garage door or the wall.

Keep the headlights on the low beam setting.
Use the markings you made on the wall or garage door to, check where the light shines and see if the centerlines still match up with the masking tape marks. If the centerlines of the two beams do not align with the tape marks, you can adjust one or both sides as needed.

Make the necessary adjustments with the lights still on while watching the light beams on the wall and your marks.
Turning the top adjusting screws in a clockwise direction will raise the beam while counterclockwise turn will lower it.

Turning the side adjuster screws will adjust the lights to the left or right.

Continue the adjustments until the center of the light beams are aligned with the tape marks. Then adjust the vertical alignment of both beams slightly below the marks on the wall. This will assure that the lights are tilted slightly downward so they won’t blind approaching motorist.

The will align bot lights, the high and low sine both are connected to the same headlight!!

Nov 18, 2009 | 2000 Chrysler 300M

1 Answer

Chrysler town country 1996 headlight adjustment.how do i do that.they are to low and to high


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 29, 2009 | 1999 Dodge Caravan

2 Answers

How do I adjust the headlights to see further down the road on my 2004 Chrysler Pacifica?


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 12, 2009 | 2004 Chrysler Pacifica

2 Answers

Adjust the headlights on 2005 Sebring, Touring Sedan


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall. Also mark where the center of the bulbs would be (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall. For horizontal, aim the hot spot directly at the line you marked for the center of your bulbs

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Aug 10, 2009 | Chrysler Sebring Cars & Trucks

Not finding what you are looking for?
2011 Chrysler 200 Logo

2,390 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...