How do i remove the power window motor driver door

if no door or window switches work in entire car start by checking FUSES , then by spraying compressed air into the switches on the drivers door panel whilst moving switches back and forth. then spray some WD40 or electronic componet cleaner into edges of switches whist moving switches hoping they come back to life. then pulling open drivers door rubber harness cover where it enters car. look for wires in the loom that are cracked and broken. this is likely.as wires bend each time door is opened. then remove drivers door panel and test then remove loom connector from door frame and use OHM /volt meter to find broken wires or switches in drivers door problems in drivers door. check for voltage at window motor first. . buy whole new door panel with wiring harness and switches at Pick n pull. if that does not work ..buy a haynes manual and look at wiring schematics. NEVER GIVE UP. NEVER BUY NEW PARTS.

You have to remove the inner door panel to
access the window regulator

You remove the regulator & then the motor from it

You Tube Video will provide a visual of several
similar window motor replacement jobs

Go there-- enter your car,question ,details,etc--- then move
around the site to watch various things

For all types of power window problem and power windows not working,i suggest you to go through the help links given below.Click the link to go through its procedure to troubleshoot the problem :------

driver side power window problem?
http://technoanswers.blogspot.com/2011/06/driver-side-window-problem-on-mercury.html

-----------

Driver side power window wont go up?
http://howtobyme.blogspot.com/2011/10/driver-side-power-window-wont-go-up-on.html

---------

Power window problem
http://repairhelpcenter.blogspot.com/2012/01/pontiac-grand-am-power-window-not.html
------------

rear door or window will not open ?
http://technoanswers.blogspot.com/2011/06/rear-door-or-window-will-not-open-on.html
--------------
How to remove door panel, door window motor and regulator ?
http://technoanswers.blogspot.com/2011/05/how-to-remove-door-panel-door-window.html

--------

Power windows not working after car wash?

http://howtobyme.blogspot.com/2011/11/power-windows-not-working-after-car.html
---------power locks, power window and power mirror not working?
http://howtobyme.blogspot.com/2011/09/power-locks-power-window-and-power.html

All power windows not working?
http://howtobyme.blogspot.com/2011/09/all-power-windows-not-working-on-2003.html
------------
How to remove window motor and regulator on Volkswagen Car?
http://howtobyme.blogspot.com/2011/09/how-to-remove-window-motor-and.html
-------------Complete Diagnosis & Testing Power Windows?

http://repairhelpcenter.blogspot.in/2012/02/diagnosis-testing-power-windows.html

------------

How to replace power window motor in car?
http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-power-window-motor-in.html
----------
HOW TO REPLACE A POWER WINDOW SWITCH
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-power-window-switch.html
------------
How to Replace a Window Motor
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-window-motor.html
----------
HOW TO REPLACE A WINDOW REGULATOR WITH MOTOR
http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-window-regulator-with.html
---------
HOW TO REPLACE WINDOW RUN CHANNEL SEALS
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-window-run-channel-seals.html
-------
HOW TO REPLACE A WINDOW REGULATOR
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-window-regulator.html

-----------This will help.Thanks.

Good directions with pictures on removing the door panel from Muth Signal mirrors
http://www.muthco.com/support/manuals/
Search on the page for the MY range and type under the Ford section.

The motor is easy to remove with a hole saw, if this is the motor that is causing the issue.
http://www.f150online.com/forums/electrical-systems/237795-removing-window-motor.html

Best to remove the door panel, and apply power directly to the pigtail on the motor, 1 direction is up, reverse polarity is down.
This is what the pigtail looks like on the motor in the door

rmove all screws on door panel, and any trim. Pull firmly on bottom of panel to remove, to test the motor all you need is a test light, if you have power and ground with key on the motor is bad

no it will not. you can even take the guide rails out from the door and remove the motor.

I would check all the fuses first, then the switch, then the motor, before I replaced the window operator. The panel should pop right off after removing a couple screws behind the handles, maybe a couple along the bottom behind little buttons. Your car looks new, I can't believe the motor has quit already.

Did you check for power at the switches. Are you sure the fuses are ok. Sometimes the wires break because of opening the door. You will have to inspect the harness and maybe have to remove the door panel. Most likely its a driver door wiring issue or the fuse.

Ive yet seen a jeep window come off track. sounds like your window regulator is broke but hopefully im wrong. anyways, remove all the screws some have cover over them, just remove the cover and youll see some sort of screw. Then pull out and try not to breake the plastic clips that pop into door. its pretty easy once you just look at if for a min. let me know if you have anymore questions about this

You need power window regulator as the cable of the regulator is out its place ,

1. Remove the gusset cover.
2. Pull up the inner door handle cover toward you to remove the upper hook. Pull down it to remove the lower hook. Remove the inner door handle cover.
3. Remove the power window switch assembly.
4. Using a trim panel remover, remove the clips of the trim panel.
5. Remove the speaker.
6. Using a spatula, remove the door sealer.
7. Remove the outer mirror assembly.
8. Remove the front end of the door weatherstrip and gusset.
9. Remove the stabilizers.
10. Remove the rear end of the door weatherstrip (inner and outer).
11. Operate the power windows switch so the bolts from the regular assembly are visible through the service holes. Remove the mounting nuts.
12. Take out the door glass. CAUTIONDo not turn the regulator in closing direction after removal of the glass. Otherwise gear may be disengaged.
13. Loosen the nuts to remove the rear sash.
14. Disconnect the power window motor wiring harness.
15. Loosen the four bolts and two nuts to pull out the regulator assembly.
16. Remove the screws to remove the motor from the regulator assembly.
17. Installation is the reverse order of removal.

Good luck...