Question about Mercedes-Benz E-Class

Open Question

I am looking for a workshop manual to set the timing of my mercededes e280 1995 or 1996 not sure it is a twin cam

Got the car with head and cam in the boot of the car

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Third cylinder head can't get the car to run right push on the gas & the car stumbles there is no power check eng. says cam sensor bad changed it problem continues does this mean this head is bad


no
it means that the cam shft timing is not correct and is retarded
get the workshop manual as there are specific ways to set the timing in relation to the cam shaft advance mechanism

Mar 10, 2018 | Cars & Trucks

1 Answer

Need help with timing marks , I'm not sure if volvo uses top dead center to set timing marks, because my are way off


all engines are set on TDC
you did not mention the engine or if it is chain or belt so this is for chain.2.8L
crank key is in line with lh cam shaft center
LH key is vertical
RH key is facing down to the left in the 8o'clock position
for belt drive engines the crankshaft mark is 12 o'clock and both cam shafts are at12 o'clock on the head and two other marks facing2oclock on the lh cam and 10 o'clock on the rh cam
It is complicated to explain but it is in the workshop manual as to how to set it up correctly

Jul 26, 2017 | Volvo Cars & Trucks

2 Answers

Cyl head gasket replacement on a Nissan Duke HR16 vvti engine 2015


best advice is to get a workshop manual for the engine
next
heads can generally be removed in car
next set the valve timing before removing the belt. check and record the position of the cam timing marks
don't move the crank after the head is pulled

Oct 02, 2016 | Cars & Trucks

1 Answer

2002 cavalier head torque spectson head bolts, and cams bolts


Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
Chevy Cavalier 1995 2005 Factory Service Workshop repair manual

Jul 30, 2016 | Cars & Trucks

1 Answer

The timing mark I would like to get


Valve timing or ignition timing?

There is a mark on the crankshaft pulley and marks on the engine block.

For valve timing you need the workshop manual, especially with twin overhead cams.

Jun 09, 2016 | Cars & Trucks

2 Answers

How do I find out if my 1999 Lanos is a twin cam or single?


you can read it in the manual, or if your familiar with the engine parts remove the cylinder head cover, you'll seethe valves and cams, then you'll know if its single or twin... but i think its a twin cam... if im not mistaken...

Mar 31, 2011 | 1999 Daewoo Lanos

1 Answer

I have a 1999 chrysler 2.7 twin cam,timing belt off,resetting the timing,which way i point the timing marks?


take the rocker cover off and look at the cams for the timing marks ,might be a falt on the back of the cam that has to be level with the head ,also turn engine over by hand before trying to start,remove no1 plug and make sure piston is at the top

Apr 11, 2010 | 1999 Chrysler Sebring

1 Answer

I am in need of the torque settings on a 92 cresida twin over head cam 3L for the harmonic balancer, timing belt tensioner and cam pullies.


if you call auto zone they will be able to give you the torque specs. and the pattern... or you can go to the library and look in the chilton or haynes manuals...

Mar 19, 2010 | 1992 Toyota Cressida

3 Answers

How to set the twin cam ,on a renault megane 1400cc after a snapped cam belt ,i had the head repaired at a shop,have all the timing tools to refit the belt and cam,s , BUT HOW TO FIT THE CAMS IN THE RIGHT...


a renault ,real euro car this one ,no problem here at all ,bring the pistons to TDC the bring back a bit so no piston is at the top ,mark it whilst its at the top with a thin white paint mark on the sprocket ,then back it down a bit .fit head because i sure the head bolts are under the cams ,then fit cams and make sure the inlet and exhaust valves are closed on no1 .no4 should be open with the cam lobes pointing down ,now look for the timing marks,they could be a lug on the cam pointing at something or a slot on the back of the camshaft that has to horizontal with the head ,or even a hole in the front pulley that aligns with a hole indent in the head that has an 8mm bolt push in to hold gear wheel in place -then when you find the marks bring the bottom sprocket back to the mark ,the actual mark is on the flywheel as i remember a special tool with a spring loaded pin to locate flywheel is used ,the fit the belt ,seem to remember a white line here on the belt that aligns with the cams a well ?? look iam old and i forget things ,then make sure you turn engine over twice on bottom pulley with a ratchet to ensure valves clear before starting -

Jan 02, 2010 | 1997 Toyota RAV4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

85111 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...